Page organisation in this revision
- Page type
- Reference hub
- Subject
- Engine ECU
- Parent
- Syvecs Standalone ECUs
- Applies to
- No ECU-specific applicability
- Tool groups
- None
- Manufacturers
- None
Changes from revision 1 to revision 2
Removed text is struck through; added text is highlighted.
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Toyota GR Yaris, with product code SGDI-Yaris. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs Toyota GR Yaris installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
Sources
Syvecs Toyota GR Yaris product listing and applicationManufacturer kit installation and pinout manualSyvecs plug-in kit support index
26-way additional I/O headerThe Syvecs application manual documents the rear additional I/O header. This is not the OEM vehicle connector pinout. Verify hardware revision, connector view, current limits and configuration; a pin labelled available may be assigned to an existing device.Rev1 hardware, 2022–2023PinSyvecs functionSource note1Ground—2K-type −—3K-type +—4GDI4−—5GDI4+—6DensoHtr1 / Slave1Out1Spare output if OEM Denso is not used7Vbat12 V bench supply or NTK lambda heater output8Fuel11Spare output9RS232 RX—10Lam1vNTK L2H2 gray wire11Lam1iNTK L2H2 white wire12LamGndNTK L2H2 black wire13Vbat-–Source describes 12 V bench supply or NTK heater output; confirm label14Out3 / Slave1Out3Spare output15RS232 TX—16CAN2LExpansion / dashboard CAN low17CAN2HExpansion / dashboard CAN high18CAN3LExpansion / dashboard CAN low19CAN3HExpansion / dashboard CAN high20Out4 / Slave1Out4Spare output21H-Bridge5—22H-Bridge6—23LAN RX−Orange/white24LAN RX+White/orange25LAN TX−Green/white26LAN TX+White/greenRev2 hardware, purchases from 2024 onwardsPinSyvecs functionSource note1Ground—2K-type −—3K-type +—4GDI4−—5GDI4+—6Out1 / Slave1Out1Spare output if OEM Denso is not used7Vbat12 V bench supply or NTK lambda heater output8Fuel11Spare output9RS232 RX—10Lam1vNTK L2H2 gray wire11Lam1iNTK L2H2 white wire12LamGndNTK L2H2 black wire13Vbat-–Source describes 12 V bench supply or NTK heater output; confirm label145 V regulated supply—15RS232 TX—16CAN2LExpansion / dashboard CAN low17CAN2HExpansion / dashboard CAN high18CAN3LExpansion / dashboard CAN low19CAN3HExpansion / dashboard CAN high20Out4 / Slave1Out4Spare output21AN01Input22S1AN05 / Slave1AN05Input23LAN RX−Orange/white24LAN RX+White/orange25LAN TX−Green/white26LAN TX+White/greenPin 13 is written “Vbat-–” while the same sentence describes a 12 V supply or heater output. Confirm the polarity with Syvecs for the actual hardware before connecting it. The source does not provide the full OEM vehicle main-connector schedule here.
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 1: Syvecs Toyota GR Yaris Plug-in ECU
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Toyota GR Yaris, with product code SGDI-Yaris. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs Toyota GR Yaris installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
Sources
Revision 2: Syvecs Toyota GR Yaris Plug-in ECU
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Toyota GR Yaris, with product code SGDI-Yaris. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs Toyota GR Yaris installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
Sources
26-way additional I/O header
The Syvecs application manual documents the rear additional I/O header. This is not the OEM vehicle connector pinout. Verify hardware revision, connector view, current limits and configuration; a pin labelled available may be assigned to an existing device.
Rev1 hardware, 2022–2023
| Pin | Syvecs function | Source note |
|---|
| 1 | Ground | — |
| 2 | K-type − | — |
| 3 | K-type + | — |
| 4 | GDI4− | — |
| 5 | GDI4+ | — |
| 6 | DensoHtr1 / Slave1Out1 | Spare output if OEM Denso is not used |
| 7 | Vbat | 12 V bench supply or NTK lambda heater output |
| 8 | Fuel11 | Spare output |
| 9 | RS232 RX | — |
| 10 | Lam1v | NTK L2H2 gray wire |
| 11 | Lam1i | NTK L2H2 white wire |
| 12 | LamGnd | NTK L2H2 black wire |
| 13 | Vbat-– | Source describes 12 V bench supply or NTK heater output; confirm label |
| 14 | Out3 / Slave1Out3 | Spare output |
| 15 | RS232 TX | — |
| 16 | CAN2L | Expansion / dashboard CAN low |
| 17 | CAN2H | Expansion / dashboard CAN high |
| 18 | CAN3L | Expansion / dashboard CAN low |
| 19 | CAN3H | Expansion / dashboard CAN high |
| 20 | Out4 / Slave1Out4 | Spare output |
| 21 | H-Bridge5 | — |
| 22 | H-Bridge6 | — |
| 23 | LAN RX− | Orange/white |
| 24 | LAN RX+ | White/orange |
| 25 | LAN TX− | Green/white |
| 26 | LAN TX+ | White/green |
Rev2 hardware, purchases from 2024 onwards
| Pin | Syvecs function | Source note |
|---|
| 1 | Ground | — |
| 2 | K-type − | — |
| 3 | K-type + | — |
| 4 | GDI4− | — |
| 5 | GDI4+ | — |
| 6 | Out1 / Slave1Out1 | Spare output if OEM Denso is not used |
| 7 | Vbat | 12 V bench supply or NTK lambda heater output |
| 8 | Fuel11 | Spare output |
| 9 | RS232 RX | — |
| 10 | Lam1v | NTK L2H2 gray wire |
| 11 | Lam1i | NTK L2H2 white wire |
| 12 | LamGnd | NTK L2H2 black wire |
| 13 | Vbat-– | Source describes 12 V bench supply or NTK heater output; confirm label |
| 14 | 5 V regulated supply | — |
| 15 | RS232 TX | — |
| 16 | CAN2L | Expansion / dashboard CAN low |
| 17 | CAN2H | Expansion / dashboard CAN high |
| 18 | CAN3L | Expansion / dashboard CAN low |
| 19 | CAN3H | Expansion / dashboard CAN high |
| 20 | Out4 / Slave1Out4 | Spare output |
| 21 | AN01 | Input |
| 22 | S1AN05 / Slave1AN05 | Input |
| 23 | LAN RX− | Orange/white |
| 24 | LAN RX+ | White/orange |
| 25 | LAN TX− | Green/white |
| 26 | LAN TX+ | White/green |
Pin 13 is written “Vbat-–” while the same sentence describes a 12 V supply or heater output. Confirm the polarity with Syvecs for the actual hardware before connecting it. The source does not provide the full OEM vehicle main-connector schedule here.