Removed text is struck through; added text is highlighted.
Syvecs S7Plus general-purpose ECU shown as a family reference; vehicle-specific kit and adaptor may differ. Manufacturer photograph, reproduced with permission. Image source.
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Toyota Supra 1998-2000 VVTi S7Plus, with product code S7Plus-TSUPRA-1. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs Toyota Supra 1998-2000 VVTi S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
Sources
Syvecs Toyota Supra 1998-2000 VVTi S7Plus product listing and applicationManufacturer kit installation and pinout manualSyvecs plug-in kit support index
S7Plus ECU-to-car connector scheduleThese 94 assignments are transcribed from the Syvecs Supra 1998–2000 S7Plus kit manual, version 1.2. The left column is the S7Plus ECU cavity; the other columns preserve its signal and the car pin or note given by Syvecs. Empty source fields are not proof that a cavity or vehicle wire is unused. Verify transmission, loom, hardware and connector orientation against Syvecs before wiring.Source ambiguity: the table uses car pin G1 for both C10 (AN01) and C25 (AN16), with different functions. The manual's boost FAQ also refers to an S6Plus, so confirm the intended pin and kit configuration rather than resolving these by assumption.S7Plus pinSyvecs signalCar pin and note in sourceA1PWR CTR OUTA2H‐Bridge1 / SlaveOut17D | DBWA3H‐Bridge2 / SlaveOut28D | DBWA4H‐Bridge3 / SlaveOut31F | S1 Auto SolenoidA5H‐Bridge4 / SlaveOut42F | S2 Auto SolenoidA6H‐Bridge5 / SlaveOut53F | SD Auto SolenoidA7H‐Bridge6 / SlaveOut66F | S4 Auto SolenoidA8H‐Bridge7 / SlaveOut7VSV ‐ Intake ControlA9H‐Bridge8 / SlaveOut8VSV ‐ Exhaust ControlA10FUEL1E5 | Injector1A11FUEL2E6 | Injector2A12FUEL3D1 | Injector3A13FUEL4D2 | Injector4A14FUEL5D3 | Injector5A15FUEL6D4 | Injector6A16FUEL7VSV ‐ Exhaust BypassA17FUEL8C6 | Knock LightA18PWM1 /*FUEL9G20 | Tacho ‐ Needs 12v PullupA19PWM2 / *FUEL10G13 | A/C ClutchA20PWM3 / *FUEL11D15 | Boost SolenoidA21PWM4 / *FUEL12A22PWM5D17 | VVTA23PWM615F | SLT ‐ Needs FlybackA24PWM713F | SLU ‐ Needs FlybackA25PWM814F | SLN ‐ Needs FlybackA26IGN1D11 | Ignition 1A27IGN2D12 | Ignition 2A28IGN3D13 | Ignition 3A29IGN4C5 | Fuel PumpA30IGN5Ignition 5A31IGN6Ignition 6A32PWRGNDD19 | DBW Clutch GroundA33PWRGNDD21A34PWRGNDD31B1PWRGNDE1B2CAN2LB3CAN2HB4KNOCKExternal Knock LoomB5KNOCK 2External Knock LoomB6PVBATB7IVBATC16,C8, D20 | 12vB8LAM1ANernst CellB9LAM1BIon PumpB10LAM1CCal Trim ResistorB11LAM1DVirtual GroundB12LAM1HEATERB13IVBATD18, F7, F8, F9 | VVTI + / Auto Solenoids 12vB14LAM2ANernst CellB15LAM2BIon PumpB16LAM2CCal Trim ResistorB17LAM2DVirtual GroundB18LAM2HEATERB19IVBATLambda 12vB20KLINEB21RS232RXB22RS232TXB23LANRX‐B24LANRX+B25LANTX‐B26LANTX+C1KNOCKGNDExternal LoomC2ANGNDD22, E18C3ANGND10F, 11F | Auto Box sensor GroundsC4ANGNDC55V OUTE2C65V OUTC75V OUTC8CAN LC9CAN HC10AN01D10 | G1C11AN02D23 | NEC12AN03G18 | RR ABSC13AN04C14AN05H7 | FR ABSC15AN06H8 | FL ABSC16AN075F | AT SpeedC17AN08E24 | TPS2C18AN09E15 | PPS1C19AN10E23 | TPS1C20AN11E9 | MAPC21AN12E16 | PPS2C22AN13E14 | Coolent TempC23AN14E22 | Air tempC24AN15Cal SwitchC25AN16G1 | A/CC26EGT1-C27EGT1+C28PWR CTR INC29AN S1 / Slave An01G16 | R SwitchC30AN S2 / Slave An02G4 | Up SwitchC31AN S3 / Slave An03G14 | Down SwitchC32AN S4 / Slave An04G7 | Manual ModeC33AN S5 / Slave An05F17 | Auto Trans TempC34AN S6 / Slave An06G27 | N And R Switch
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 1: Syvecs Toyota Supra 1998-2000 VVTi S7Plus Plug-in ECUSyvecs S7Plus general-purpose ECU shown as a family reference; vehicle-specific kit and adaptor may differ. Manufacturer photograph, reproduced with permission. Image source.
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Toyota Supra 1998-2000 VVTi S7Plus, with product code S7Plus-TSUPRA-1. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs Toyota Supra 1998-2000 VVTi S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
Revision 2: Syvecs Toyota Supra 1998-2000 VVTi S7Plus Plug-in ECUSyvecs S7Plus general-purpose ECU shown as a family reference; vehicle-specific kit and adaptor may differ. Manufacturer photograph, reproduced with permission. Image source.
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Toyota Supra 1998-2000 VVTi S7Plus, with product code S7Plus-TSUPRA-1. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs Toyota Supra 1998-2000 VVTi S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
These 94 assignments are transcribed from the Syvecs Supra 1998–2000 S7Plus kit manual, version 1.2. The left column is the S7Plus ECU cavity; the other columns preserve its signal and the car pin or note given by Syvecs. Empty source fields are not proof that a cavity or vehicle wire is unused. Verify transmission, loom, hardware and connector orientation against Syvecs before wiring.
Source ambiguity: the table uses car pin G1 for both C10 (AN01) and C25 (AN16), with different functions. The manual's boost FAQ also refers to an S6Plus, so confirm the intended pin and kit configuration rather than resolving these by assumption.