Removed text is struck through; added text is highlighted.
Syvecs S7Plus general-purpose ECU shown as a family reference; vehicle-specific kit and adaptor may differ. Manufacturer photograph, reproduced with permission. Image source.
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Nissan R35 GTR 2009-2019 S7Plus, with product code S7Plus-NGTR. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs Nissan R35 GTR 2009-2019 S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
Sources
Syvecs Nissan R35 GTR 2009-2019 S7Plus product listing and applicationManufacturer kit installation and pinout manualSyvecs plug-in kit support index
R35 kit ECU connector schedulesThe Syvecs R35GTR kit manual, pages 10–12, documents the S7Plus ECU connector assignments below. These are ECU pins, not the original Nissan harness pinout. The manufacturer states the 2020-onward kit uses a different vehicle connector; verify the precise adapter and model year before using these assignments.Connector A — 34 wayPinSyvecs I/OKit function / source noteA1PWR CTR OUTThrottle and main relayA2H-Bridge1 / SlaveOut1DBWA3H-Bridge2 / SlaveOut2DBWA4H-Bridge3 / SlaveOut3DBWA5H-Bridge4 / SlaveOut4DBWA6H-Bridge5 / SlaveOut5Boost solenoidA7H-Bridge6 / SlaveOut6Fuel pump 2A8H-Bridge7 / SlaveOut7EvapA9H-Bridge8 / SlaveOut8—A10FUEL1Primary injector 1A11FUEL2Primary injector 2A12FUEL3Primary injector 3A13FUEL4Primary injector 4A14FUEL5Primary injector 5A15FUEL6Primary injector 6A16FUEL7Secondary injector 1 or spareA17FUEL8Secondary injector 2 or spareA18PWM1 / *FUEL9Secondary injector 3 or spareA19PWM2 / *FUEL10Secondary injector 4 or spareA20PWM3 / *FUEL11Fuel pump controller – 5 V pull-upA21PWM4 / *FUEL12Secondary injector 5 or spareA22PWM5Secondary injector 6 or spareA23PWM6TachoA24PWM7VVT1A25PWM8VVT2A26IGN1Ignition 1A27IGN2Ignition 2A28IGN3Ignition 3A29IGN4Ignition 4A30IGN5Ignition 5A31IGN6Ignition 6A32PWRGNDPower groundA33PWRGNDPower groundA34PWRGNDPower groundConnector B — 26 wayPinSyvecs I/OKit function / source noteB1PWRGNDPower groundB2CAN2L—B3CAN2H—B4KNOCK—B5KNOCK 2—B6PVBATConstant 12 VB7IVBAT12 VB8LAM1A2.2 V per sourceB9LAM1B—B10LAM1C—B11LAM1D—B12LAM1HEATERLambda heaterB13IVBAT12 VB14LAM2A2.2 V per sourceB15LAM2B1.8 V per sourceB16LAM2C—B17LAM2D—B18LAM2HEATERLambda heaterB19IVBAT12 VB20KLINE—B21RS232RX—B22RS232TX—B23LANRX−Cat5 pin 2B24LANRX+Cat5 pin 1B25LANTX−Cat5 pin 6B26LANTX+Cat5 pin 3Connector C — 34 wayPinSyvecs I/OKit function / source noteC1KNOCKGND—C2ANGNDSensor groundC3ANGNDSensor groundC4ANGNDSensor groundC55V OUT—C65V OUT—C75V OUT—C8CAN L—C9CAN H—C10AN01TPS1AC11AN02TPS1BC12AN03TPS2AC13AN04TPS2BC14AN05Cam position sensorC15AN06Crank position sensorC16AN07Cam 2 position sensorC17AN08Oil temperatureC18AN09MAP absolute sensorC19AN10PPS1C20AN11PPS2C21AN12Brake switchC22AN13Fuel temperatureC23AN14Air charge temperatureC24AN15Coolant temperatureC25AN16Cruise control switchC26EGT1−—C27EGT1+—C28PWR CTR INIgnition switchC29AN S1 / Slave An01Secondary air injection (flex fuel)C30AN S2 / Slave An02MAF1 / spare inputC31AN S3 / Slave An03MAF2 / spare inputC32AN S4 / Slave An04—C33AN S5 / Slave An05Pre-throttle MAP1 / spare inputC34AN S6 / Slave An06Pre-throttle MAP2 / spare inputThe source repeats lambda-1 software labels for the LAM2A–D section. Confirm the second lambda channel with Syvecs rather than assuming the wiring is identical.
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 1: Syvecs Nissan R35 GTR 2009-2019 S7Plus Plug-in ECUSyvecs S7Plus general-purpose ECU shown as a family reference; vehicle-specific kit and adaptor may differ. Manufacturer photograph, reproduced with permission. Image source.
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Nissan R35 GTR 2009-2019 S7Plus, with product code S7Plus-NGTR. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs Nissan R35 GTR 2009-2019 S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
Revision 2: Syvecs Nissan R35 GTR 2009-2019 S7Plus Plug-in ECUSyvecs S7Plus general-purpose ECU shown as a family reference; vehicle-specific kit and adaptor may differ. Manufacturer photograph, reproduced with permission. Image source.
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Nissan R35 GTR 2009-2019 S7Plus, with product code S7Plus-NGTR. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs Nissan R35 GTR 2009-2019 S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
The Syvecs R35GTR kit manual, pages 10–12, documents the S7Plus ECU connector assignments below. These are ECU pins, not the original Nissan harness pinout. The manufacturer states the 2020-onward kit uses a different vehicle connector; verify the precise adapter and model year before using these assignments.
Connector A — 34 way
Pin
Syvecs I/O
Kit function / source note
A1
PWR CTR OUT
Throttle and main relay
A2
H-Bridge1 / SlaveOut1
DBW
A3
H-Bridge2 / SlaveOut2
DBW
A4
H-Bridge3 / SlaveOut3
DBW
A5
H-Bridge4 / SlaveOut4
DBW
A6
H-Bridge5 / SlaveOut5
Boost solenoid
A7
H-Bridge6 / SlaveOut6
Fuel pump 2
A8
H-Bridge7 / SlaveOut7
Evap
A9
H-Bridge8 / SlaveOut8
—
A10
FUEL1
Primary injector 1
A11
FUEL2
Primary injector 2
A12
FUEL3
Primary injector 3
A13
FUEL4
Primary injector 4
A14
FUEL5
Primary injector 5
A15
FUEL6
Primary injector 6
A16
FUEL7
Secondary injector 1 or spare
A17
FUEL8
Secondary injector 2 or spare
A18
PWM1 / *FUEL9
Secondary injector 3 or spare
A19
PWM2 / *FUEL10
Secondary injector 4 or spare
A20
PWM3 / *FUEL11
Fuel pump controller – 5 V pull-up
A21
PWM4 / *FUEL12
Secondary injector 5 or spare
A22
PWM5
Secondary injector 6 or spare
A23
PWM6
Tacho
A24
PWM7
VVT1
A25
PWM8
VVT2
A26
IGN1
Ignition 1
A27
IGN2
Ignition 2
A28
IGN3
Ignition 3
A29
IGN4
Ignition 4
A30
IGN5
Ignition 5
A31
IGN6
Ignition 6
A32
PWRGND
Power ground
A33
PWRGND
Power ground
A34
PWRGND
Power ground
Connector B — 26 way
Pin
Syvecs I/O
Kit function / source note
B1
PWRGND
Power ground
B2
CAN2L
—
B3
CAN2H
—
B4
KNOCK
—
B5
KNOCK 2
—
B6
PVBAT
Constant 12 V
B7
IVBAT
12 V
B8
LAM1A
2.2 V per source
B9
LAM1B
—
B10
LAM1C
—
B11
LAM1D
—
B12
LAM1HEATER
Lambda heater
B13
IVBAT
12 V
B14
LAM2A
2.2 V per source
B15
LAM2B
1.8 V per source
B16
LAM2C
—
B17
LAM2D
—
B18
LAM2HEATER
Lambda heater
B19
IVBAT
12 V
B20
KLINE
—
B21
RS232RX
—
B22
RS232TX
—
B23
LANRX−
Cat5 pin 2
B24
LANRX+
Cat5 pin 1
B25
LANTX−
Cat5 pin 6
B26
LANTX+
Cat5 pin 3
Connector C — 34 way
Pin
Syvecs I/O
Kit function / source note
C1
KNOCKGND
—
C2
ANGND
Sensor ground
C3
ANGND
Sensor ground
C4
ANGND
Sensor ground
C5
5V OUT
—
C6
5V OUT
—
C7
5V OUT
—
C8
CAN L
—
C9
CAN H
—
C10
AN01
TPS1A
C11
AN02
TPS1B
C12
AN03
TPS2A
C13
AN04
TPS2B
C14
AN05
Cam position sensor
C15
AN06
Crank position sensor
C16
AN07
Cam 2 position sensor
C17
AN08
Oil temperature
C18
AN09
MAP absolute sensor
C19
AN10
PPS1
C20
AN11
PPS2
C21
AN12
Brake switch
C22
AN13
Fuel temperature
C23
AN14
Air charge temperature
C24
AN15
Coolant temperature
C25
AN16
Cruise control switch
C26
EGT1−
—
C27
EGT1+
—
C28
PWR CTR IN
Ignition switch
C29
AN S1 / Slave An01
Secondary air injection (flex fuel)
C30
AN S2 / Slave An02
MAF1 / spare input
C31
AN S3 / Slave An03
MAF2 / spare input
C32
AN S4 / Slave An04
—
C33
AN S5 / Slave An05
Pre-throttle MAP1 / spare input
C34
AN S6 / Slave An06
Pre-throttle MAP2 / spare input
The source repeats lambda-1 software labels for the LAM2A–D section. Confirm the second lambda channel with Syvecs rather than assuming the wiring is identical.