Removed text is struck through; added text is highlighted.
Syvecs S7Plus general-purpose ECU shown as a family reference; vehicle-specific kit and adaptor may differ. Manufacturer photograph, reproduced with permission. Image source.
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as McLaren MP4-12C, with product code S7Plus-M838T-MP4. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs McLaren MP4-12C installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
Sources
Syvecs McLaren MP4-12C product listing and applicationManufacturer kit installation and pinout manualSyvecs plug-in kit support index
M838T kit ECU connector schedulesFrom Syvecs M838T kit manual, version 1.2, pages 5–7, which lists MP4-12C, 570 and 650S. These are the S7Plus ECU's three connectors, not the original vehicle loom pins. Match the adapter, configuration, source connector view and electrical limits to the actual car.Connector A — 34 wayPinSyvecs I/OKit function / source noteA1PWR CTR OUTMain relayA2H-Bridge1 / SlaveOut1DBW1A3H-Bridge2 / SlaveOut2DBW1A4H-Bridge3 / SlaveOut3DBW2A5H-Bridge4 / SlaveOut4DBW2A6H-Bridge5 / SlaveOut5Thermostat ×2A7H-Bridge6 / SlaveOut6Starter low sideA8H-Bridge7 / SlaveOut7Wastegate 1A9H-Bridge8 / SlaveOut8Wastegate 2A10FUEL1Primary injector 1A11FUEL2Primary injector 2A12FUEL3Primary injector 3A13FUEL4Primary injector 4A14FUEL5Primary injector 5A15FUEL6Primary injector 6A16FUEL7Primary injector 7A17FUEL8Primary injector 8A18FUEL9—A19FUEL10Fuel pump ×2A20FUEL11EvapA21FUEL12Dump valve ×2A22FUEL13VVT1 intakeA23FUEL14VVT2 intakeA24FUEL15VVT1 exhaustA25FUEL16VVT2 exhaustA26IGN1IGN1 & 4A27IGN2IGN5 & 8A28IGN3IGN2 & 3A29IGN4IGN6 & 7A30IGN5Radiator fan 1A31IGN6Radiator fan 2A32PWRGNDIntake sound generator groundA33PWRGNDGroundA34PWRGNDGroundConnector B — 26 wayPinSyvecs I/OKit function / source noteB1PWRGNDPower groundB2CAN 2LCAN 2B3CAN 2HCAN 2B4KNOCK—B5KNOCK 2—B6PVBATConstant 12 VB7IVBAT12 VB8LAM1ALSU 4.9 connector pin 6B9LAM1BLSU 4.9 connector pin 1B10LAM1CLSU 4.9 connector pin 5B11LAM1DLSU 4.9 connector pin 2B12LAM1HEATERLSU 4.9 connector pin 3B13IVBAT12 VB14LAM2ASource repeats LSU 4.9 pin 6; confirm with SyvecsB15LAM2BSource repeats LSU 4.9 pin 1; confirm with SyvecsB16LAM2CSource repeats LSU 4.9 pin 5; confirm with SyvecsB17LAM2DSource repeats LSU 4.9 pin 2; confirm with SyvecsB18LAM2HEATERSource repeats LSU 4.9 pin 3; confirm with SyvecsB19IVBAT12 V; starter relay high sideB20KLINEAlternator LINB21RS232RXSource says set as CAN L for throttle body with CAN bridgeB22RS232TXSource says set as CAN H for throttle body with CAN bridgeB23LANRX−Cat5 pin 2B24LANRX+Cat5 pin 1B25LANTX−Cat5 pin 6B26LANTX+Cat5 pin 3Connector C — 34 wayPinSyvecs I/OKit function / source noteC1KNOCKGNDKnock groundC2ANGNDB sensor groundsC3ANGNDSensor groundC4ANGNDSensor groundC55V OUTB 5 VC65V OUTA 5 VC75V OUT—C8CAN L—C9CAN H—C10AN01Crank sensorC11AN02VVT1 intakeC12AN03VVT2 intakeC13AN04VVT1 exhaustC14AN05VVT2 exhaustC15AN06MAP manifoldC16AN07TPS2AC17AN08TPS2BC18AN09PPS1C19AN10PPS2C20AN11TPS1AC21AN12TPS1BC22AN13ACT1C23AN14Park neutral switchC24AN15Coolant temperatureC25AN16Intake sound signalC26EGT1−—C27EGT1+—C28PWR CTR IN12 V ignitionC29AN S1 / Slave An01Fuel pressureC30AN S2 / Slave An02Fuel temperatureC31AN S3 / Slave An03—C32AN S4 / Slave An04Oil pressure switchC33AN S5 / Slave An05MAP1C34AN S6 / Slave An06MAP2The manual repeats lambda-1 software labels and LSU pin numbers for the LAM2A–D section. Confirm second-sensor wiring with Syvecs. The manufacturer does not publish the OEM car connector pinout in this schedule.
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 1: Syvecs McLaren MP4-12C Plug-in ECUSyvecs S7Plus general-purpose ECU shown as a family reference; vehicle-specific kit and adaptor may differ. Manufacturer photograph, reproduced with permission. Image source.
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as McLaren MP4-12C, with product code S7Plus-M838T-MP4. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs McLaren MP4-12C installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
Revision 2: Syvecs McLaren MP4-12C Plug-in ECUSyvecs S7Plus general-purpose ECU shown as a family reference; vehicle-specific kit and adaptor may differ. Manufacturer photograph, reproduced with permission. Image source.
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as McLaren MP4-12C, with product code S7Plus-M838T-MP4. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs McLaren MP4-12C installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
From Syvecs M838T kit manual, version 1.2, pages 5–7, which lists MP4-12C, 570 and 650S. These are the S7Plus ECU's three connectors, not the original vehicle loom pins. Match the adapter, configuration, source connector view and electrical limits to the actual car.
Connector A — 34 way
Pin
Syvecs I/O
Kit function / source note
A1
PWR CTR OUT
Main relay
A2
H-Bridge1 / SlaveOut1
DBW1
A3
H-Bridge2 / SlaveOut2
DBW1
A4
H-Bridge3 / SlaveOut3
DBW2
A5
H-Bridge4 / SlaveOut4
DBW2
A6
H-Bridge5 / SlaveOut5
Thermostat ×2
A7
H-Bridge6 / SlaveOut6
Starter low side
A8
H-Bridge7 / SlaveOut7
Wastegate 1
A9
H-Bridge8 / SlaveOut8
Wastegate 2
A10
FUEL1
Primary injector 1
A11
FUEL2
Primary injector 2
A12
FUEL3
Primary injector 3
A13
FUEL4
Primary injector 4
A14
FUEL5
Primary injector 5
A15
FUEL6
Primary injector 6
A16
FUEL7
Primary injector 7
A17
FUEL8
Primary injector 8
A18
FUEL9
—
A19
FUEL10
Fuel pump ×2
A20
FUEL11
Evap
A21
FUEL12
Dump valve ×2
A22
FUEL13
VVT1 intake
A23
FUEL14
VVT2 intake
A24
FUEL15
VVT1 exhaust
A25
FUEL16
VVT2 exhaust
A26
IGN1
IGN1 & 4
A27
IGN2
IGN5 & 8
A28
IGN3
IGN2 & 3
A29
IGN4
IGN6 & 7
A30
IGN5
Radiator fan 1
A31
IGN6
Radiator fan 2
A32
PWRGND
Intake sound generator ground
A33
PWRGND
Ground
A34
PWRGND
Ground
Connector B — 26 way
Pin
Syvecs I/O
Kit function / source note
B1
PWRGND
Power ground
B2
CAN 2L
CAN 2
B3
CAN 2H
CAN 2
B4
KNOCK
—
B5
KNOCK 2
—
B6
PVBAT
Constant 12 V
B7
IVBAT
12 V
B8
LAM1A
LSU 4.9 connector pin 6
B9
LAM1B
LSU 4.9 connector pin 1
B10
LAM1C
LSU 4.9 connector pin 5
B11
LAM1D
LSU 4.9 connector pin 2
B12
LAM1HEATER
LSU 4.9 connector pin 3
B13
IVBAT
12 V
B14
LAM2A
Source repeats LSU 4.9 pin 6; confirm with Syvecs
B15
LAM2B
Source repeats LSU 4.9 pin 1; confirm with Syvecs
B16
LAM2C
Source repeats LSU 4.9 pin 5; confirm with Syvecs
B17
LAM2D
Source repeats LSU 4.9 pin 2; confirm with Syvecs
B18
LAM2HEATER
Source repeats LSU 4.9 pin 3; confirm with Syvecs
B19
IVBAT
12 V; starter relay high side
B20
KLINE
Alternator LIN
B21
RS232RX
Source says set as CAN L for throttle body with CAN bridge
B22
RS232TX
Source says set as CAN H for throttle body with CAN bridge
B23
LANRX−
Cat5 pin 2
B24
LANRX+
Cat5 pin 1
B25
LANTX−
Cat5 pin 6
B26
LANTX+
Cat5 pin 3
Connector C — 34 way
Pin
Syvecs I/O
Kit function / source note
C1
KNOCKGND
Knock ground
C2
ANGND
B sensor grounds
C3
ANGND
Sensor ground
C4
ANGND
Sensor ground
C5
5V OUT
B 5 V
C6
5V OUT
A 5 V
C7
5V OUT
—
C8
CAN L
—
C9
CAN H
—
C10
AN01
Crank sensor
C11
AN02
VVT1 intake
C12
AN03
VVT2 intake
C13
AN04
VVT1 exhaust
C14
AN05
VVT2 exhaust
C15
AN06
MAP manifold
C16
AN07
TPS2A
C17
AN08
TPS2B
C18
AN09
PPS1
C19
AN10
PPS2
C20
AN11
TPS1A
C21
AN12
TPS1B
C22
AN13
ACT1
C23
AN14
Park neutral switch
C24
AN15
Coolant temperature
C25
AN16
Intake sound signal
C26
EGT1−
—
C27
EGT1+
—
C28
PWR CTR IN
12 V ignition
C29
AN S1 / Slave An01
Fuel pressure
C30
AN S2 / Slave An02
Fuel temperature
C31
AN S3 / Slave An03
—
C32
AN S4 / Slave An04
Oil pressure switch
C33
AN S5 / Slave An05
MAP1
C34
AN S6 / Slave An06
MAP2
The manual repeats lambda-1 software labels and LSU pin numbers for the LAM2A–D section. Confirm second-sensor wiring with Syvecs. The manufacturer does not publish the OEM car connector pinout in this schedule.