Removed text is struck through; added text is highlighted.
Syvecs S7Plus general-purpose ECU shown as a family reference; vehicle-specific kit and adaptor may differ. Manufacturer photograph, reproduced with permission. Image source.
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Mitsubishi Evo X Manual SST S7Plus, with product code S7Plus-EVOX. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs Mitsubishi Evo X Manual SST S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
Sources
Syvecs Mitsubishi Evo X Manual SST S7Plus product listing and applicationManufacturer kit installation and pinout manualSyvecs plug-in kit support index
Manufacturer ECU connector schedulesFrom the Syvecs Mitsubishi Evo X installation guide, revision 1.2. The tables list ECU-side pins and the manufacturer's vehicle-specific notes, not the complete original vehicle connectors. A dash denotes a blank field in the source, not proof of an unused circuit. Confirm the ECU, harness revision and connector orientation against the manufacturer document.Connector AECU pinSyvecs descriptionFunctionApplication notesA1PWR CTR OUTMAIN RELAY OUTPUTMain RelayA2H‐Bridge1 / SlaveOut1H‐Bridge1DBW+A3H‐Bridge2 / SlaveOut2H‐Bridge2DBW‐A4H‐Bridge3 / SlaveOut3H‐Bridge3—A5H‐Bridge4 / SlaveOut4H‐Bridge4—A6H‐Bridge5 / SlaveOut5H‐Bridge5Evap SolenoidA7H‐Bridge6 / SlaveOut6H‐Bridge6Evap Emission SolenoidA8H‐Bridge7 / SlaveOut7H‐Bridge7Spray BarsA9H‐Bridge8 / SlaveOut8H‐Bridge8—A10FUEL1INJECTOR or PWM OUTPUTPrimary Injector 1A11FUEL2INJECTOR or PWM OUTPUTPrimary Injector 2A12FUEL3INJECTOR or PWM OUTPUTPrimary Injector 3A13FUEL4INJECTOR or PWM OUTPUTPrimary Injector 4A14FUEL5INJECTOR or PWM OUTPUTWastegate SolenoidA15FUEL6INJECTOR or PWM OUTPUTWastegate Solenoid 2A16FUEL7INJECTOR or PWM OUTPUTAirCon Comp RelayA17FUEL8INJECTOR or PWM OUTPUTThrottle RelayA18PWM1 /*FUEL9PWM OUTPUTFuel Pump RelayA19PWM2 / *FUEL10PWM OUTPUTAlternator ControlA20PWM3 / *FUEL11PWM OUTPUTFuel Pump Relay 2A21PWM4 / *FUEL12PWM OUTPUT—A22PWM5PWM OUTPUT—A23PWM6PWM OUTPUT—A24PWM7PWM OUTPUTVVT IntakeA25PWM8PWM OUTPUTVVT ExhaustA26IGN1CYL 1 IGNITION OUTPUTIgnition 1A27IGN2CYL 2 IGNITION OUTPUTIgnition 2A28IGN3CYL 3 IGNITION OUTPUTIgnition 3A29IGN4CYL 4 IGNITION OUTPUTIgnition 4A30IGN5CYL 5 IGNITION OUTPUT—A31IGN6CYL 6 IGNITION OUTPUT—A32PWRGNDPOWER GROUNDThrottle Ground and Cruise GroundA33PWRGNDPOWER GROUNDThrottle GroundA34PWRGNDPOWER GROUNDECM GroundConnector BECU pinSyvecs descriptionFunctionApplication notesB1PWRGNDPOWER GROUNDGroundB2CAN2L——B3CAN2H——B4KNOCKKNOCK—B5KNOCK2KNOCK2—B6PVBAT——B7IVBAT——B8LAM1ALamv / LamD1+/ LamLun1Grey NTKB9LAM1BLami / LamD1‐ /LamIP1White NTKB10LAM1CLamLIA1—B11LAM1DLamGND / LamLVM1Black NTKB12LAM1HEATERLAMBDA HEATERBlue NTKB13IVBAT—Yellow NTKB14LAM2ALamv / LamD1+/ LamLun1—B15LAM2BLami / LamD1‐ /LamIP1—B16LAM2CLamLIA1—B17LAM2DLamGND / LamLVM1—B18LAM2HEATERLAMBDA HEATER—B19IVBAT—Power SupplyB20KLINEKline—B21RS232RXRS232RX—B22RS232TXRS232TX—B23LANRX‐Cat5 Pin2—B24LANRX+Cat5 Pin1—B25LANTX‐Cat5 Pin6—B26LANTX+Cat5 Pin3—Connector CECU pinSyvecs descriptionFunctionApplication notesC1KNOCK GROUNDKNOCK GROUND—C2ANGNDSENSOR GNDTPS,C3ANGNDSENSOR GND—C4ANGNDSENSOR GND—C55V OUT5V OUTExhaust Cam Sensor, TPSC65V OUT5V OUT—C75V OUT5V OUT—C8CAN LCan Low—C9CAN HCan High—C10AN01BI-POLAR INPUTSCrank SensorC11AN02BI-POLAR INPUTSExhaust Cam SensorC12AN03BI-POLAR INPUTSIntake Cam SensorC13AN04BI-POLAR INPUTS—C14AN05UNI-POLAR INPUTS—C15AN06UNI-POLAR INPUTS—C16AN07UNI-POLAR INPUTSTPS1AC17AN08UNI-POLAR INPUTSTPS1BC18AN09VOLT-INPUTSMAP Absolute SensorC19AN10VOLT-INPUTSPPS1C20AN11VOLT-INPUTSPPS2C21AN12VOLT-INPUTSMAFC22AN13RESISTIVE INPUTSAir Charge Temp 2C23AN14RESISTIVE INPUTSAir Charge TempC24AN15RESISTIVE INPUTSECT1C25AN16RESISTIVE INPUTSCruise SwitchC26EGT1-EGT1 -—C27EGT1+EGT1 +—C28PWR CTR INMAIN RELAY INPUT SWIgnition SwitchC29AN S1 / Slave An01UNI-POLAR INPUTSAlternator FeedC30AN S2 / Slave An02UNI-POLAR INPUTSOil Pressure SwC31AN S3 / Slave An03UNI-POLAR INPUTSClutch SwC32AN S4 / Slave An04UNI-POLAR INPUTSFuel tempC33AN S5 / Slave An05UNI-POLAR INPUTSSpray Bar RequestC34AN S6 / Slave An06UNI-POLAR INPUTSBrake Switch
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 1: Syvecs Mitsubishi Evo X Manual SST S7Plus Plug-in ECUSyvecs S7Plus general-purpose ECU shown as a family reference; vehicle-specific kit and adaptor may differ. Manufacturer photograph, reproduced with permission. Image source.
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Mitsubishi Evo X Manual SST S7Plus, with product code S7Plus-EVOX. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs Mitsubishi Evo X Manual SST S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
Revision 2: Syvecs Mitsubishi Evo X Manual SST S7Plus Plug-in ECUSyvecs S7Plus general-purpose ECU shown as a family reference; vehicle-specific kit and adaptor may differ. Manufacturer photograph, reproduced with permission. Image source.
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Mitsubishi Evo X Manual SST S7Plus, with product code S7Plus-EVOX. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs Mitsubishi Evo X Manual SST S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
From the Syvecs Mitsubishi Evo X installation guide, revision 1.2. The tables list ECU-side pins and the manufacturer's vehicle-specific notes, not the complete original vehicle connectors. A dash denotes a blank field in the source, not proof of an unused circuit. Confirm the ECU, harness revision and connector orientation against the manufacturer document.