Removed text is struck through; added text is highlighted.
Golf Mk7.5 R S7D plug-in ECU. Image: Syvecs product page, reproduced with permission.
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Golf Mk7.5 R GTI E888 Gen3 S7D, with product code S7D-VW7.5RDF. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs Golf Mk7.5 R GTI E888 Gen3 S7D installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
Sources
Syvecs Golf Mk7.5 R GTI E888 Gen3 S7D product listing and applicationManufacturer kit installation and pinout manualSyvecs plug-in kit support index
MQB4 S7D ECU and accessory connector schedulesThe Syvecs MQB4 S7D kit manual identifies ECU connectors A–D and a separate 26-way accessory connector. These are ECU or accessory connector positions and documented functions, not OEM factory connector cavity numbers. Check the correct kit, wiring, electrical limits, ECU variant and connector orientation before applying them.Source conflicts: In the same document B2/B3 are labelled CAN2 low/high but their OEM-function column says K-type thermocouple; accessory B14/B15 are labelled CAN3 low/high but the notes also say K-type EGT. The second lambda labels duplicate several first-lambda names and the B18 OEM column says Slave Out 10. The entries below preserve the document and require confirmation with Syvecs rather than an assumed correction.A connectorTerminalSyvecs labelFunction / OEM note in sourceA1PWR CTR OUTMain relay outputA2H-Bridge1H-Bridge1A3H-Bridge2H-Bridge2A4H-Bridge3H-Bridge3A5H-Bridge4H-Bridge4A6H-Bridge5H-Bridge5A7H-Bridge6H-Bridge6A8H-Bridge7H-Bridge7A9H-Bridge8H-Bridge8A10GDI LS1Port injector 1; fuel 1 / low-side GDI 1A11GDI LS2DI injector 1−A12GDI LS3Port injector 2; fuel 3 / low-side GDI 3A13GDI LS4DI injector 2−A14GDI LS5Port injector 3; fuel 5 / low-side GDI 5A15GDI LS6DI injector 3−A16GDI LS7Port injector 4; fuel 7 / low-side GDI 7A17GDI LS8DI injector 4−A18GDI HS1/2DI injector 1+A19GDI HS3/4DI injector 2+A20GDI Pump 1 HSDI pump high sideA21GDI HS5/6DI injector 3+A22GDI HS7/8DI injector 4+A23GDI Pump 2 HSNC in OEM function columnA24GDI Pump 1 LowSideFuel 15 outputA25Fuel 16Fuel 16 outputA26IGN1Cylinder 1 ignition outputA27IGN2Cylinder 2 ignition outputA28IGN3Cylinder 3 ignition outputA29IGN4Cylinder 4 ignition outputA30IGN5DI pump lowA31IGN6Tacho syncA32PWRGNDPower groundA33PWRGNDPower groundA34PWRGNDPower groundB connectorTerminalSyvecs labelFunction / OEM note in sourceB1PWRGNDPower groundB2CAN2 LCAN 2; OEM column says K-type thermoB3CAN2 HCAN 2; OEM column says K-type thermoB4KNOCK 1Knock 1B5KNOCK 2Knock 2B6PVBATConstant 12 VB7IVBAT12 VB8LAM1ALamV / LamD1+ / LamLun1B9LAM1BLamI / LamD1− / LamIP1B10LAM1CLamLIA1B11LAM1DLamGND / LamLVM1B12LAM1HEATERLambda heaterB13IVBAT12 VB14LAM2ALamV / LamD1+ / LamLun1B15LAM2BLamI / LamD1− / LamIP1B16LAM2CLamLIA1B17LAM2DLamGND / LamLVM1B18LAM2HEATERLambda heater; OEM column says Slave Out 10B19IVBAT12 VB20KLINEK-lineB21RS232RXRS232 RXB22RS232TXRS232 TXB23LANRX−Cat5 pin 2B24LANRX+Cat5 pin 1B25LANTX−Cat5 pin 6B26LANTX+Cat5 pin 3C connectorTerminalSyvecs labelFunction / OEM note in sourceC1KNOCKGNDKnock groundC2ANGNDSensor groundC3ANGNDSensor groundC4ANGNDSensor groundC55V OUT5 V outputC65V OUT5 V outputC75V OUT5 V outputC8CAN1 LCAN 1 lowC9CAN1 HCAN 1 highC10AN01Bipolar inputC11AN02Bipolar inputC12AN03Bipolar inputC13AN04Bipolar inputC14AN05Unipolar inputC15AN06Unipolar inputC16AN07Unipolar inputC17AN08Unipolar inputC18AN09Voltage inputC19AN10Voltage inputC20AN11Voltage inputC21AN12Voltage inputC22AN13Resistive inputC23AN14Resistive inputC24AN15Resistive inputC25AN16Resistive inputC26EGT1−EGT 1 negativeC27EGT1+EGT 1 positiveC28PWR CTR INMain relay input switchC29AN S1Unipolar inputC30AN S2Unipolar inputC31AN S3Unipolar inputC32AN S4Unipolar inputC33AN S5Unipolar inputC34AN S6Unipolar inputD connectorTerminalSyvecs labelFunction / OEM note in sourceD1DVBAT1GDI power supplyD2DVBAT2GDI power supplyD3DVBAT3GDI power supplyD4DVBAT4GDI power supplyD5FUEL9PWM / fuel outputD6FUEL10PWM / fuel outputD7FUEL11PWM / fuel outputD8FUEL12PWM / fuel outputD9FUEL13PWM / fuel outputD10FUEL14PWM / fuel outputD11LSO1PWM outputD12LSO2PWM outputD13LSO3PWM outputD14LSO4PWM outputD15LSO5PWM outputD16LSO6PWM outputD17EGT2−EGT 2 negativeD18EGT2+EGT 2 positiveD19NCNC in sourceD20NCNC in sourceD21NCNC in sourceD22NCNC in sourceD23CAN3LCAN 3 lowD24CAN3HCAN 3 highD25PWRGNDPower groundD26PWRGNDPower groundAccessory connectorTerminalSyvecs labelFunction / OEM note in sourceB1GroundB2HBR3B3HBR4B4HBR5B5Fuel15B6Fuel16B712 VB8LAMHtr2B9CAN2LSpare CANB10CAN2HSpare CANB11RS232RXB12RS232TXB13LAM2ASpare input S1AN10B14CAN3LK-type EGT (as written in source)B15CAN3HK-type EGT (as written in source)B16Lam2CSpare input S1AN11B17EGT1−B18EGT1+B19AN15Spare inputB20S1AN04B21ANGroundSensor groundB225 V5 V output for sensorsB23LANRX−EthernetB24LANRX+EthernetB25LANTX−EthernetB26LANTX+Ethernet
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Golf Mk7.5 R GTI E888 Gen3 S7D, with product code S7D-VW7.5RDF. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs Golf Mk7.5 R GTI E888 Gen3 S7D installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
Revision 3: Syvecs Golf Mk7.5 R GTI E888 Gen3 S7D Plug-in ECUGolf Mk7.5 R S7D plug-in ECU. Image: Syvecs product page, reproduced with permission.
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Golf Mk7.5 R GTI E888 Gen3 S7D, with product code S7D-VW7.5RDF. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs Golf Mk7.5 R GTI E888 Gen3 S7D installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
The Syvecs MQB4 S7D kit manual identifies ECU connectors A–D and a separate 26-way accessory connector. These are ECU or accessory connector positions and documented functions, not OEM factory connector cavity numbers. Check the correct kit, wiring, electrical limits, ECU variant and connector orientation before applying them.
Source conflicts: In the same document B2/B3 are labelled CAN2 low/high but their OEM-function column says K-type thermocouple; accessory B14/B15 are labelled CAN3 low/high but the notes also say K-type EGT. The second lambda labels duplicate several first-lambda names and the B18 OEM column says Slave Out 10. The entries below preserve the document and require confirmation with Syvecs rather than an assumed correction.