Removed text is struck through; added text is highlighted.
Syvecs S7Plus general-purpose ECU shown as a family reference; vehicle-specific kit and adaptor may differ. Manufacturer photograph, reproduced with permission. Image source.
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Can-Am Maverick X3 2017-2019 S7Plus, with product code S7Plus-CanAm. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Application discrepancy: the product page specifies 2017–2019, while Syvecs' separate manuals index labels its X3 guide 2015–2017. Verify VIN, engine and harness with Syvecs before relying on the shared guide.
Wiring and pinout
Syvecs Can-Am Maverick X3 2017-2019 S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
Sources
Syvecs Can-Am Maverick X3 2017-2019 S7Plus product listing and applicationManufacturer kit installation and pinout manualSyvecs plug-in kit support index
Manufacturer ECU connector schedulesFrom the Syvecs Can-Am X3 installation guide, revision 1.2. These are the manufacturer-listed ECU-side functions. The manual index and product listing differ on model years; verify the actual vehicle and loom with Syvecs. A blank means the guide leaves the entry blank. Confirm the orientation, loom revision, and configured functions against the manufacturer guide before connecting.Connector AECU pinSyvecs descriptionFunctionApplication notesA1PWR CTR OUTMAIN RELAY OUTPUTMain RelayA2H-Bridge1 / SlaveOut1H-Bridge1DBWA3H-Bridge2 / SlaveOut2H-Bridge2DBWA4H-Bridge3 / SlaveOut3H-Bridge3—A5H-Bridge4 / SlaveOut4H-Bridge4Start Signal or SolenoidA6H-Bridge5 / SlaveOut5H-Bridge5—A7H-Bridge6 / SlaveOut6H-Bridge6—A8H-Bridge7 / SlaveOut7H-Bridge7—A9H-Bridge8 / SlaveOut8H-Bridge8—A10FUEL1INJECTOR or PWM OUTPUTPrimary Injector 1A11FUEL2INJECTOR or PWM OUTPUTPrimary Injector 2A12FUEL3INJECTOR or PWM OUTPUTPrimary Injector 3A13FUEL4INJECTOR or PWM OUTPUTAcc RelayA14FUEL5INJECTOR or PWM OUTPUT—A15FUEL6INJECTOR or PWM OUTPUT—A16FUEL7INJECTOR or PWM OUTPUT—A17FUEL8INJECTOR or PWM OUTPUT—A18PWM1 /*FUEL9PWM OUTPUTBoost SolenoidA19PWM2 / *FUEL10PWM OUTPUTFuel PumpA20PWM3 / *FUEL11PWM OUTPUTRad Fan Relay - CanAmA21PWM4 / *FUEL12PWM OUTPUTTurbo Intercooler Fan Relay - CanAmA22PWM5PWM OUTPUT—A23PWM6PWM OUTPUT—A24PWM7PWM OUTPUT—A25PWM8PWM OUTPUT—A26IGN1CYL 1 IGNITION OUTPUTIgnition 1A27IGN2CYL 2 IGNITION OUTPUTIgnition 2A28IGN3CYL 3 IGNITION OUTPUTIgnition 3A29IGN4CYL 4 IGNITION OUTPUT—A30IGN5CYL 5 IGNITION OUTPUT—A31IGN6CYL 6 IGNITION OUTPUT—A32PWRGNDPOWER GROUNDLanyard Sw GroundA33PWRGNDPOWER GROUND—A34PWRGNDPOWER GROUND—Connector BECU pinSyvecs descriptionFunctionApplication notesB1PWRGNDPOWER GROUND—B2CAN2L——B3CAN2H——B4KNOCKKNOCK—B5KNOCK 2KNOCK 2—B6PVBATCONSTANT 12V—B7IVBAT12v—B8LAM1ALamv / LamD1+/ LamLun1Grey NTKB9LAM1BLami / LamD1- /LamIP1White NTKB10LAM1CLamLIA1—B11LAM1DLamGND / LamLVM1Black NTKB12LAM1HEATERLAMBDA HEATERBlue NTKB13IVBAT12VYellow NTKB14LAM2ALamv / LamD1+/ LamLun12.2vB15LAM2BLami / LamD1- /LamIP11.8vB16LAM2CLamLIA1—B17LAM2DLamGND / LamLVM1—B18LAM2HEATERLAMBDA HEATER—B19IVBAT12V—B20KLINEKline—B21RS232RXRS232RX—B22RS232TXRS232TX—B23LANRX-Cat5 Pin2—B24LANRX+Cat5 Pin1—B25LANTX-Cat5 Pin6—B26LANTX+Cat5 Pin3—Connector CECU pinSyvecs descriptionFunctionApplication notesC1KNOCKGNDKNOCKGND—C2ANGNDSENSOR GND—C3ANGNDSENSOR GNDSteering Lock,C4ANGNDSENSOR GND—C55V OUT5V OUTTPS, MapC65V OUT5V OUTSport/ Eco Switch on CanAmC75V OUT5V OUTGear Pot 5v - CanAmC8CAN LCan LowCan LowC9CAN HCan HighCan HighC10AN01BI-POLAR INPUTSTPS 1AC11AN02BI-POLAR INPUTSTPS 1BC12AN03BI-POLAR INPUTSCrank Position SensorC13AN04BI-POLAR INPUTSGear Sensor / Oil PressureC14AN05UNI-POLAR INPUTSCam Position SensorC15AN06UNI-POLAR INPUTSGear Speed - CanAmC16AN07UNI-POLAR INPUTSStart SignalC17AN08UNI-POLAR INPUTS—C18AN09VOLT-INPUTSMAP Absolute SensorC19AN10VOLT-INPUTSPPS1C20AN11VOLT-INPUTSPPS2C21AN12VOLT-INPUTSGear LeverC22AN13RESISTIVE INPUTS—C23AN14RESISTIVE INPUTSIntake TempC24AN15RESISTIVE INPUTSExhaust Manifold TempC25AN16RESISTIVE INPUTSCharge TempC26EGT1-EGT1 -—C27EGT1+EGT1 +—C28PWR CTR INMAIN RELAY INPUT SW—C29AN S1 / Slave An01UNI-POLAR INPUTS—C30AN S2 / Slave An02UNI-POLAR INPUTSSport/ Eco Switch on CanAmC31AN S3 / Slave An03UNI-POLAR INPUTSBrake SwC32AN S4 / Slave An04UNI-POLAR INPUTSSeat Belt Switch - CanAmC33AN S5 / Slave An05UNI-POLAR INPUTS—C34AN S6 / Slave An06UNI-POLAR INPUTS—
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 1: Syvecs Can-Am Maverick X3 2017-2019 S7Plus Plug-in ECUSyvecs S7Plus general-purpose ECU shown as a family reference; vehicle-specific kit and adaptor may differ. Manufacturer photograph, reproduced with permission. Image source.
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Can-Am Maverick X3 2017-2019 S7Plus, with product code S7Plus-CanAm. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Application discrepancy: the product page specifies 2017–2019, while Syvecs' separate manuals index labels its X3 guide 2015–2017. Verify VIN, engine and harness with Syvecs before relying on the shared guide.
Wiring and pinout
Syvecs Can-Am Maverick X3 2017-2019 S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
Revision 2: Syvecs Can-Am Maverick X3 2017-2019 S7Plus Plug-in ECUSyvecs S7Plus general-purpose ECU shown as a family reference; vehicle-specific kit and adaptor may differ. Manufacturer photograph, reproduced with permission. Image source.
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Can-Am Maverick X3 2017-2019 S7Plus, with product code S7Plus-CanAm. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Application discrepancy: the product page specifies 2017–2019, while Syvecs' separate manuals index labels its X3 guide 2015–2017. Verify VIN, engine and harness with Syvecs before relying on the shared guide.
Wiring and pinout
Syvecs Can-Am Maverick X3 2017-2019 S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
From the Syvecs Can-Am X3 installation guide, revision 1.2. These are the manufacturer-listed ECU-side functions. The manual index and product listing differ on model years; verify the actual vehicle and loom with Syvecs. A blank means the guide leaves the entry blank. Confirm the orientation, loom revision, and configured functions against the manufacturer guide before connecting.