Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
Syvecs Standalone ECUs
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Changes from revision 1 to revision 2

Removed text is struck through; added text is highlighted.

Syvecs S7Plus general-purpose ECU shown as a family reference; vehicle-specific kit and adaptor may differ. Manufacturer photograph, reproduced with permission. Image source.

Model and vehicle application

Syvecs lists this vehicle-specific standalone or plug-in ECU kit as BMW 135 335 N54 S7Plus, with product code S7plus-N54. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.

This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.

Confirmed installation details

The kit covers specified BMW 135 and 335 N54 applications. Its installation guide describes an ECU, adaptor harness and separate direct-injection driver; the supplied base calibration must match the engine's manifold pressure, turbocharger and fuel system configuration.

In the illustrated kit connector A, A2 and A3 are drive-by-wire H-bridge outputs and A4 is assigned to the DI pump. Follow the complete guide and confirm the hardware revision before using these examples.

Wiring and pinout

Syvecs BMW 135 335 N54 S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.

For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.

Calibration and service

Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.

Sources

Syvecs BMW 135 335 N54 S7Plus product listing and applicationManufacturer kit installation and pinout manualSyvecs plug-in kit support index

N54 kit ECU and direct-injection driver pin schedulesFrom Syvecs N54 PNP manual, pages 5–7. These numbers identify the Syvecs ECU and separate DI driver connectors, not the original BMW connector. Empty cells mean the source gives no function. Check connector views, hardware and calibration; the DI driver and injector circuits are model-specific.A — 34-way, key 1PinSyvecs I/O nameApplication or source noteA1PWR CTR OUTMain relayA2H-Bridge1 / SlaveOut1DBWA3H-Bridge2 / SlaveOut2DBWA4H-Bridge3 / SlaveOut3DI pumpA5H-Bridge4 / SlaveOut4VANOS intake low sideA6H-Bridge5 / SlaveOut5VANOS exhaust low sideA7H-Bridge6 / SlaveOut6ThermostatA8H-Bridge7 / SlaveOut7Spare outputA9H-Bridge8 / SlaveOut8Spare outputA10FUEL1Primary injector 1A11FUEL2Primary injector 2A12FUEL3Primary injector 3A13FUEL4Primary injector 4A14FUEL5Primary injector 5A15FUEL6Primary injector 6A16FUEL7Port injector 1 / spareA17FUEL8Port injector 2 / spareA18PWM1 / *FUEL9Port injector 3 / spareA19PWM2 / *FUEL10Engine fan 105 HzA20PWM3 / *FUEL11Port injector 4 / spareA21PWM4 / *FUEL12Exhaust flap / port injector 5A22PWM5Fuel tank ventA23PWM6Wastegate 1A24PWM7Wastegate 2A25PWM8Port injector 6 / spareA26IGN1Ignition 1A27IGN2Ignition 2A28IGN3Ignition 3A29IGN4Ignition 4A30IGN5Ignition 5A31IGN6Ignition 6A32PWRGNDPower groundA33PWRGNDPower groundA34PWRGNDPower groundB — 26-way, key 1PinSyvecs I/O nameApplication or source noteB1PWRGNDPower groundB2CAN2L—B3CAN2H−As labelled in source; confirm polarityB4KNOCKExternal loomB5KNOCK 2External loomB6PVBATConstant 12 VB7IVBAT12 VB8LAM1ALSU 4.9 connector pin 6B9LAM1BLSU 4.9 connector pin 1B10LAM1CLSU 4.9 connector pin 5B11LAM1DLSU 4.9 connector pin 2B12LAM1HEATERLSU 4.9 connector pin 3B13IVBAT12 VB14LAM2ASource repeats LSU 4.9 pin 6; confirm with SyvecsB15LAM2BSource repeats LSU 4.9 pin 1; confirm with SyvecsB16LAM2CSource repeats LSU 4.9 pin 5; confirm with SyvecsB17LAM2DSource repeats LSU 4.9 pin 2; confirm with SyvecsB18LAM2HEATERSource repeats LSU 4.9 pin 3; confirm with SyvecsB19IVBAT12 VB20KLINEEngine coolant pump and oil levelB21RS232RX—B22RS232TX—B23LANRX−Cat5 pin 2B24LANRX+Cat5 pin 1B25LANTX−Cat5 pin 6B26LANTX+Cat5 pin 3C — 34-way, key 2PinSyvecs I/O nameApplication or source noteC1KNOCKGNDKnock groundC2ANGNDSensor groundC3ANGNDSensor groundC4ANGNDSensor groundC55V OUT—C65V OUT—C75V OUT—C8CAN LPowertrain CANC9CAN HPowertrain CANC10AN01Direct injection pressureC11AN02Crank position sensorC12AN03SpeedC13AN04MAP sensorC14AN05VVT1 intakeC15AN06VVT2 exhaustC16AN07Spare inputC17AN08Spare inputC18AN09TPS1AC19AN10TPS1BC20AN11PPSAC21AN12PPSBC22AN13Intake air temperatureC23AN14Spare inputC24AN15Coolant temperatureC25AN16Oil pressure switchC26EGT1−—C27EGT1+—C28PWR CTR IN12 V ignitionC29AN S1 / Slave An01Brake light switchC30AN S2 / Slave An02—C31AN S3 / Slave An03Clutch switchC32AN S4 / Slave An04Spare inputC33AN S5 / Slave An05Fuel pressureC34AN S6 / Slave An06Barometric pressureDirect-injection driver — 35-wayPinSyvecs I/O nameApplication or source note1INJ1−Injector 1 negative2INJ2−Injector 2 negative3INJ3−Injector 3 negative4——5INJ5−Injector 5 negative6INJ6−Injector 6 negative7——8INJ4−Injector 4 negative9GNDGround10INJ1_INInjector 1 control input11INJ2_INInjector 2 control input12——13INJ1+Injector 1 positive14INJ2+Injector 2 positive15INJ3+Injector 3 positive16——17INJ5+Injector 5 positive18INJ6+Injector 6 positive19——20INJ4+Injector 4 positive21GNDGround22INJ3_INInjector 3 control input23——24GNDGround25——26——27IGN+12 V switched ignition28——29——30CAN HCAN high31CAN LCAN low32——33INJ4_INInjector 4 control input34INJ5_INInjector 5 control input35INJ6_INInjector 6 control inputFor B3 the manufacturer labels the channel “CAN2 H−”; confirm the polarity before connecting. B14–B18 repeat lambda-1 software labels and LSU pin numbers in the manual's second lambda section; confirm the actual lambda wiring with Syvecs. A5 and A6 are described as low-side VANOS assignments in this kit schedule.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 1: Syvecs BMW 135 335 N54 S7Plus Plug-in ECU
Syvecs S7Plus general-purpose ECU
Syvecs S7Plus general-purpose ECU shown as a family reference; vehicle-specific kit and adaptor may differ. Manufacturer photograph, reproduced with permission. Image source.

Model and vehicle application

Syvecs lists this vehicle-specific standalone or plug-in ECU kit as BMW 135 335 N54 S7Plus, with product code S7plus-N54. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.

This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.

Confirmed installation details

The kit covers specified BMW 135 and 335 N54 applications. Its installation guide describes an ECU, adaptor harness and separate direct-injection driver; the supplied base calibration must match the engine's manifold pressure, turbocharger and fuel system configuration.

In the illustrated kit connector A, A2 and A3 are drive-by-wire H-bridge outputs and A4 is assigned to the DI pump. Follow the complete guide and confirm the hardware revision before using these examples.

Wiring and pinout

Syvecs BMW 135 335 N54 S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.

For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.

Calibration and service

Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.

Sources

Revision 2: Syvecs BMW 135 335 N54 S7Plus Plug-in ECU
Syvecs S7Plus general-purpose ECU
Syvecs S7Plus general-purpose ECU shown as a family reference; vehicle-specific kit and adaptor may differ. Manufacturer photograph, reproduced with permission. Image source.

Model and vehicle application

Syvecs lists this vehicle-specific standalone or plug-in ECU kit as BMW 135 335 N54 S7Plus, with product code S7plus-N54. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.

This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.

Confirmed installation details

The kit covers specified BMW 135 and 335 N54 applications. Its installation guide describes an ECU, adaptor harness and separate direct-injection driver; the supplied base calibration must match the engine's manifold pressure, turbocharger and fuel system configuration.

In the illustrated kit connector A, A2 and A3 are drive-by-wire H-bridge outputs and A4 is assigned to the DI pump. Follow the complete guide and confirm the hardware revision before using these examples.

Wiring and pinout

Syvecs BMW 135 335 N54 S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.

For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.

Calibration and service

Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.

Sources

N54 kit ECU and direct-injection driver pin schedules

From Syvecs N54 PNP manual, pages 5–7. These numbers identify the Syvecs ECU and separate DI driver connectors, not the original BMW connector. Empty cells mean the source gives no function. Check connector views, hardware and calibration; the DI driver and injector circuits are model-specific.

A — 34-way, key 1

PinSyvecs I/O nameApplication or source note
A1PWR CTR OUTMain relay
A2H-Bridge1 / SlaveOut1DBW
A3H-Bridge2 / SlaveOut2DBW
A4H-Bridge3 / SlaveOut3DI pump
A5H-Bridge4 / SlaveOut4VANOS intake low side
A6H-Bridge5 / SlaveOut5VANOS exhaust low side
A7H-Bridge6 / SlaveOut6Thermostat
A8H-Bridge7 / SlaveOut7Spare output
A9H-Bridge8 / SlaveOut8Spare output
A10FUEL1Primary injector 1
A11FUEL2Primary injector 2
A12FUEL3Primary injector 3
A13FUEL4Primary injector 4
A14FUEL5Primary injector 5
A15FUEL6Primary injector 6
A16FUEL7Port injector 1 / spare
A17FUEL8Port injector 2 / spare
A18PWM1 / *FUEL9Port injector 3 / spare
A19PWM2 / *FUEL10Engine fan 105 Hz
A20PWM3 / *FUEL11Port injector 4 / spare
A21PWM4 / *FUEL12Exhaust flap / port injector 5
A22PWM5Fuel tank vent
A23PWM6Wastegate 1
A24PWM7Wastegate 2
A25PWM8Port injector 6 / spare
A26IGN1Ignition 1
A27IGN2Ignition 2
A28IGN3Ignition 3
A29IGN4Ignition 4
A30IGN5Ignition 5
A31IGN6Ignition 6
A32PWRGNDPower ground
A33PWRGNDPower ground
A34PWRGNDPower ground

B — 26-way, key 1

PinSyvecs I/O nameApplication or source note
B1PWRGNDPower ground
B2CAN2L—
B3CAN2H−As labelled in source; confirm polarity
B4KNOCKExternal loom
B5KNOCK 2External loom
B6PVBATConstant 12 V
B7IVBAT12 V
B8LAM1ALSU 4.9 connector pin 6
B9LAM1BLSU 4.9 connector pin 1
B10LAM1CLSU 4.9 connector pin 5
B11LAM1DLSU 4.9 connector pin 2
B12LAM1HEATERLSU 4.9 connector pin 3
B13IVBAT12 V
B14LAM2ASource repeats LSU 4.9 pin 6; confirm with Syvecs
B15LAM2BSource repeats LSU 4.9 pin 1; confirm with Syvecs
B16LAM2CSource repeats LSU 4.9 pin 5; confirm with Syvecs
B17LAM2DSource repeats LSU 4.9 pin 2; confirm with Syvecs
B18LAM2HEATERSource repeats LSU 4.9 pin 3; confirm with Syvecs
B19IVBAT12 V
B20KLINEEngine coolant pump and oil level
B21RS232RX—
B22RS232TX—
B23LANRX−Cat5 pin 2
B24LANRX+Cat5 pin 1
B25LANTX−Cat5 pin 6
B26LANTX+Cat5 pin 3

C — 34-way, key 2

PinSyvecs I/O nameApplication or source note
C1KNOCKGNDKnock ground
C2ANGNDSensor ground
C3ANGNDSensor ground
C4ANGNDSensor ground
C55V OUT—
C65V OUT—
C75V OUT—
C8CAN LPowertrain CAN
C9CAN HPowertrain CAN
C10AN01Direct injection pressure
C11AN02Crank position sensor
C12AN03Speed
C13AN04MAP sensor
C14AN05VVT1 intake
C15AN06VVT2 exhaust
C16AN07Spare input
C17AN08Spare input
C18AN09TPS1A
C19AN10TPS1B
C20AN11PPSA
C21AN12PPSB
C22AN13Intake air temperature
C23AN14Spare input
C24AN15Coolant temperature
C25AN16Oil pressure switch
C26EGT1−—
C27EGT1+—
C28PWR CTR IN12 V ignition
C29AN S1 / Slave An01Brake light switch
C30AN S2 / Slave An02—
C31AN S3 / Slave An03Clutch switch
C32AN S4 / Slave An04Spare input
C33AN S5 / Slave An05Fuel pressure
C34AN S6 / Slave An06Barometric pressure

Direct-injection driver — 35-way

PinSyvecs I/O nameApplication or source note
1INJ1−Injector 1 negative
2INJ2−Injector 2 negative
3INJ3−Injector 3 negative
4——
5INJ5−Injector 5 negative
6INJ6−Injector 6 negative
7——
8INJ4−Injector 4 negative
9GNDGround
10INJ1_INInjector 1 control input
11INJ2_INInjector 2 control input
12——
13INJ1+Injector 1 positive
14INJ2+Injector 2 positive
15INJ3+Injector 3 positive
16——
17INJ5+Injector 5 positive
18INJ6+Injector 6 positive
19——
20INJ4+Injector 4 positive
21GNDGround
22INJ3_INInjector 3 control input
23——
24GNDGround
25——
26——
27IGN+12 V switched ignition
28——
29——
30CAN HCAN high
31CAN LCAN low
32——
33INJ4_INInjector 4 control input
34INJ5_INInjector 5 control input
35INJ6_INInjector 6 control input

For B3 the manufacturer labels the channel “CAN2 H−”; confirm the polarity before connecting. B14–B18 repeat lambda-1 software labels and LSU pin numbers in the manual's second lambda section; confirm the actual lambda wiring with Syvecs. A5 and A6 are described as low-side VANOS assignments in this kit schedule.