Removed text is struck through; added text is highlighted.
Syvecs S7Plus general-purpose ECU shown as a family reference; vehicle-specific kit and adaptor may differ. Manufacturer photograph, reproduced with permission. Image source.
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Audi TTRS RS3 Mk3 8V2 S7Plus, with product code S7Plus-RS3 8V2. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs Audi TTRS RS3 Mk3 8V2 S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
Sources
Syvecs Audi TTRS RS3 Mk3 8V2 S7Plus product listing and applicationManufacturer kit installation and pinout manualSyvecs plug-in kit support index
Manufacturer ECU connector schedulesFrom the Syvecs Audi RS3/TTRS 8V2 installation guide, revision 1.2. The tables list ECU-side positions and the manufacturer's kit notes, not complete original vehicle connector pinouts. The guide limits this schedule to DAZA engines. It describes B18 as LAM2HEATER in one column and Slave Out 10 in another, and gives B16 both a lambda label and a fuel-pressure SENT note; verify those conflicting assignments with Syvecs. A dash denotes an empty field in the manufacturer chart; confirm the exact loom and connector view.Connector APinSyvecs descriptionFunctionApplication notesA1PWR CTR OUTMAIN RELAY OUTPUTMain RelayA2H-Bridge1 / SlaveOut1H-Bridge1DBW +A3H-Bridge2 / SlaveOut2H-Bridge2DBW -A4H-Bridge3 / SlaveOut3H-Bridge3WG SolenoidA5H-Bridge4 / SlaveOut4H-Bridge4EvapA6H-Bridge5 / SlaveOut5H-Bridge5DI Pump Signal to DI12A7H-Bridge6 / SlaveOut6H-Bridge6Starter RelayA8H-Bridge7 / SlaveOut7H-Bridge7Intake Manifold Flap (N316)A9H-Bridge8 / SlaveOut8H-Bridge8Coolant Switch PumpA10FUEL1INJECTOR or PWM OUTPUTPrimary Injector 1A11FUEL2INJECTOR or PWM OUTPUTPrimary Injector 2A12FUEL3INJECTOR or PWM OUTPUTPrimary Injector 3A13FUEL4INJECTOR or PWM OUTPUTPrimary Injector 4A14FUEL5INJECTOR or PWM OUTPUTPrimary Injector 5A15FUEL6INJECTOR or PWM OUTPUTPort Injector 1 (N532)A16FUEL7INJECTOR or PWM OUTPUTPort Injector 2 (N533)A17FUEL8INJECTOR or PWM OUTPUTPort Injector 3 (N534)A18FUEL9INJECTOR or PWM OUTPUTPort Injector 4 (N535)A19FUEL10INJECTOR or PWM OUTPUTPort Injector 5 (N536)A20FUEL11INJECTOR or PWM OUTPUTFuel Pump PWMA21FUEL12INJECTOR or PWM OUTPUTCooling Fan PWMA22FUEL13INJECTOR or PWM OUTPUTTurbo Recirc (N249)A23FUEL14INJECTOR or PWM OUTPUTExhaust Cam Solenoids BA24FUEL15INJECTOR or PWM OUTPUTVVT1 Int (N205)A25FUEL16INJECTOR or PWM OUTPUTVVT1 Ex (N316)A26IGN1CYL 1 IGNITION OUTPUTIGN1 (N70)A27IGN2CYL 2 IGNITION OUTPUTIGN2 (N127)A28IGN3CYL 3 IGNITION OUTPUTIGN3 (N291)A29IGN4CYL 4 IGNITION OUTPUTIGN4 (N292)A30IGN5CYL 5 IGNITION OUTPUTIGN5 (N292)A31IGN6CYL 6 IGNITION OUTPUTTacho SyncA32PWRGNDPOWER GROUNDPwrGndA33PWRGNDPOWER GROUNDPwrGNdA34PWRGNDPOWER GROUNDPwrGNdConnector BPinSyvecs descriptionFunctionApplication notesB1PWRGNDPOWER GROUNDPWRGROUNDB2CAN2L——B3CAN2H——B4KNOCKKNOCKKnock +B5KNOCK 2KNOCK 2—B6PVBATCONSTANT 12V—B7IVBAT12v12v for Exhaust SolenoidValvesB8LAM1ALamv / LamD1+/ LamLun1Pin6 on LSU4.9 ConnectorB9LAM1BLami / LamD1- /LamIP1Pin1 on LSU4.9 ConnectorB10LAM1CLamLIA1Pin5 on LSU4.9 ConnectorB11LAM1DLamGND / LamLVM1Pin2 on LSU4.9 ConnectorB12LAM1HEATERLAMBDA HEATERPin3 on LSU4.9 ConnectorB13IVBAT12 V—B14LAM2ALamv / LamD1+/ LamLun1—B15LAM2BLami / LamD1- /LamIP1—B16LAM2CLamLIA1Fuel Pressure Low Side -SENTB17LAM2DLamGND / LamLVM1—B18LAM2HEATERSlave Out 10Exhaust Flap Control PWMB19IVBAT12 V—B20KLINEKline—B21RS232RXRS232RX—B22RS232TXRS232TX—B23LANRX-Cat5 Pin2—B24LANRX+Cat5 Pin1—B25LANTX-Cat5 Pin6—B26LANTX+Cat5 Pin3—Connector CPinSyvecs descriptionFunctionApplication notesC1KNOCKGNDKNOCKGNDKnock -C2ANGNDSENSOR GND—C3ANGNDSENSOR GNDTestedC4ANGNDSENSOR GND—C55V OUT5V OUTTestedC65V OUT5V OUTTestedC75V OUT5V OUT—C8CAN LCan LowPowertrain CanC9CAN HCan HighPowertrain CanC10AN01BI-POLAR INPUTSStart RequestC11AN02BI-POLAR INPUTSDiPressureC12AN03BI-POLAR INPUTSIntake Pos FlapC13AN04BI-POLAR INPUTS—C14AN05UNI-POLAR INPUTS—C15AN06UNI-POLAR INPUTSVVT1Ex PosC16AN07UNI-POLAR INPUTSCrank SensorC17AN08UNI-POLAR INPUTSBrake Lt SwC18AN09VOLT-INPUTSTPS1AC19AN10VOLT-INPUTSTPS1BC20AN11VOLT-INPUTSPPSAC21AN12VOLT-INPUTSPPSBC22AN13RESISTIVE INPUTSCoolant Temp (G62)C23AN14RESISTIVE INPUTSIntake Air TempC24AN15RESISTIVE INPUTS—C25AN16RESISTIVE INPUTS—C26EGT1-EGT1 -—C27EGT1+EGT1 +—C28PWR CTR INMAIN RELAY INPUT SWKey On sig (15)C29AN S1 / Slave An01UNI-POLAR INPUTSOil Level / TempC30AN S2 / Slave An02UNI-POLAR INPUTSOil Pressure Sensor - SENTC31AN S3 / Slave An03UNI-POLAR INPUTSSENT MAPC32AN S4 / Slave An04UNI-POLAR INPUTSSENT ACTC33AN S5 / Slave An05UNI-POLAR INPUTS—C34AN S6 / Slave An06UNI-POLAR INPUTSInterMediate Shaft Speed
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 1: Syvecs Audi TTRS RS3 Mk3 8V2 S7Plus Plug-in ECUSyvecs S7Plus general-purpose ECU shown as a family reference; vehicle-specific kit and adaptor may differ. Manufacturer photograph, reproduced with permission. Image source.
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Audi TTRS RS3 Mk3 8V2 S7Plus, with product code S7Plus-RS3 8V2. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs Audi TTRS RS3 Mk3 8V2 S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
Revision 2: Syvecs Audi TTRS RS3 Mk3 8V2 S7Plus Plug-in ECUSyvecs S7Plus general-purpose ECU shown as a family reference; vehicle-specific kit and adaptor may differ. Manufacturer photograph, reproduced with permission. Image source.
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Audi TTRS RS3 Mk3 8V2 S7Plus, with product code S7Plus-RS3 8V2. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs Audi TTRS RS3 Mk3 8V2 S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
From the Syvecs Audi RS3/TTRS 8V2 installation guide, revision 1.2. The tables list ECU-side positions and the manufacturer's kit notes, not complete original vehicle connector pinouts. The guide limits this schedule to DAZA engines. It describes B18 as LAM2HEATER in one column and Slave Out 10 in another, and gives B16 both a lambda label and a fuel-pressure SENT note; verify those conflicting assignments with Syvecs. A dash denotes an empty field in the manufacturer chart; confirm the exact loom and connector view.