Removed text is struck through; added text is highlighted.
Syvecs S12 standalone ECU shown as a family illustration. This vehicle-specific kit and its adapter or wiring are not pictured and may differ. Image: Syvecs, reproduced with permission.
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Audi R8 Gen2 2016 onward V10 S12, with product code S12-R8V1017. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs Audi R8 Gen2 2016 onward V10 S12 installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
Sources
Syvecs Audi R8 Gen2 2016 onward V10 S12 product listing and applicationManufacturer kit installation and pinout manualSyvecs plug-in kit support index
Manufacturer S12 ECU connector scheduleFrom the Syvecs Huracán / R8 Gen2 kit installation guide, pages 9–11. This covers the 121 S12 ECU positions and manufacturer descriptions; the separate DI12 and factory vehicle connectors are not fully tabulated here. The chart's guide identifies the R8 Gen2 interface as 2017 onward, while the article's product range begins in 2016; confirm a 2016 vehicle and loom with Syvecs. A dash reproduces an empty entry in the chart.S12 pinSyvecs functionKit description1PWRGND—2IGN01Ignition Coil Cyl 13IGN02Ignition Coil Cyl 24IGN03Ignition Coil Cyl 35IGN04Ignition Coil Cyl 46IN25Throttle Position 1a7KNOCK 4Knock + 48KNOCKGNDKnock Ground9THERMO 2 + _—10IN21MAF Air Temp 111IN18Pedal Position 1a12IN14Cam Position ‐ Exhaust 113IN11Cam Position ‐ Intake 114IN07Crank Position15IN04Starter Signal16IN01—17LAM 1 I—18CAN 2 LO—19RS232 TX—20LAN RX‐Orange/White21FUEL07Sec Fuel Injector 122FUEL03Sec Fuel Injector 223VBAT—24PWRGND—25IN26Throttle Position 1b265V OUT—27KNOCK 1Knock + 128THERMO 1 ‐ _—29IN22MAF Air Temp 230IN19Pedal Position 1b31IN15Cam Position ‐ Exhaust 232IN12Cam Position ‐ Intake 233IN08External Map Sensor34ANGNDTank Pressure, Cam Sensor,35IN02—36LAM 1 VNernst Cell V37CAN 3 HI—38RS232 RX—39LAN RX+White/Orange40FUEL08Sec Fuel Injector 341FUEL04Sec Fuel Injector 442VBAT—43PWRGND—44IN27Throttle Position 2a455V OUT—46KNOCK 2Knock + 247THERMO 1 + _—48IN23—49IN20Fuel Pressure ‐ Low Side150IN16Sec Air Pressure ( MAP 1)51ANGND—52IN09Sec Air Pressure ( MAP 2)53IN05Brake Light Switch54ANGND—55LAM 2 VNeret Cell V56CAN 3 LO—57RS232 GND—58CAN 1 HI—59LAN TX‐Green/White60FUEL05Sec Fuel Injector 561FUEL01Sec Fuel Injector 662HBRIDGE 6DBW 1b ‐63IN28Throttle Position 2b6410VOUT—65KNOCK 3Knock + 366THERMO 2 ‐ _—67IN24Coolant Temp 168ANGND—69IN17Fuel Pressure ‐ Low Side270IN13Fuel Pressure ‐ High Side 171IN10Fuel Pressure ‐ High Side272IN06—73IN03Oil Pressure SWiTCH74LAM 2 I—75LAM GND—76CAN 2 HI—77CAN 1 LO—78LAN TX+White/Green79FUEL06Sec Fuel Injector 780FUEL02Sec Fuel Injector 881HBRIDGE 5DBW 1 +82HBRIDGE 2DI Spill Valve 2 ‐ 12V83PWM4Lambda Heater B184PWM8Lambda Heater B285FUEL12Sec Fuel Injector 986FUEL16Sec Fuel Injector 1087FUEL20Cam Adjuster B1 Intake88FUEL24Cam Adjuster B1 Exhaust89VBAT—90HBRIDGE 1DI Spill Valve 1 ‐ 12v91PWM3Starter Relays92PWM7Brake Servo Relay93FUEL11Cam Adjuster B2 Intake94FUEL15Cam Adjuster B2 Exhaust95FUEL19DI12 Injector 196FUEL23DI12 Injector 297PWRGND—98HBRIDGE 4DBW 2 ‐99PWM2—100PWM6Boost control Sol101FUEL10DI12 Injector 3102FUEL14DI12 Injector 4103FUEL18DI12 Injector 5104FUEL22DI12 Injector 6105PWRGND—106HBRIDGE 3DBW 2 +107PWM1FuelPump108PWM5Cooling Fans109FUEL09DI12 Injector 7110FUEL13DI12 Injector 8111FUEL17DI12 Injector 9112FUEL21DI12 Injector 10113PWRGND—114IGN05Ignition Coil Cyl 5115IGN06Ignition Coil Cyl 6116IGN07Ignition Coil Cyl 7117IGN08Ignition Coil Cyl 8118IGN09Ignition Coil Cyl 9119IGN10Ignition Coil Cyl 10120IGN11DI Spill Valve 1121IGN12DI Spill Valve 2
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Audi R8 Gen2 2016 onward V10 S12, with product code S12-R8V1017. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs Audi R8 Gen2 2016 onward V10 S12 installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
Revision 3: Syvecs Audi R8 Gen2 2016 onward V10 S12 Plug-in ECUSyvecs S12 standalone ECU shown as a family illustration. This vehicle-specific kit and its adapter or wiring are not pictured and may differ. Image: Syvecs, reproduced with permission.
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Audi R8 Gen2 2016 onward V10 S12, with product code S12-R8V1017. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs Audi R8 Gen2 2016 onward V10 S12 installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
From the Syvecs Huracán / R8 Gen2 kit installation guide, pages 9–11. This covers the 121 S12 ECU positions and manufacturer descriptions; the separate DI12 and factory vehicle connectors are not fully tabulated here. The chart's guide identifies the R8 Gen2 interface as 2017 onward, while the article's product range begins in 2016; confirm a 2016 vehicle and loom with Syvecs. A dash reproduces an empty entry in the chart.