Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
MBE Systems standalone ECUs
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Changes from revision 2 to revision 3

Removed text is struck through; added text is highlighted.

The 9A9 is an MBE fuel-injection ECU for up to eight cylinders. SBD describes twin wideband lambda inputs and two CAN buses; pinout, sensor and driver suitability depends on the exact hardware and software. Source and identification.

Wiring and pinout

Model wiring documentation: Issue N2, BOM1-010 onward only; obtain the matching diagram for other builds. Check connector view, wiring harness, ECU part number and installed calibration before connecting power. Programmable input and output functions depend on the map and software.

Configuration and support

For programmable SBD-supplied ECUs, Easimap is used to inspect and change maps, subject to the interface and access of the actual ECU. Some vehicle-manufacturer supplied units are locked; SBD’s FAQ warns against attempting downloads to locked ECUs. Do not assume that a serial ECU map or harness transfers directly to a newer CAN unit.

Evidence limits

Verify the build, trigger inputs, coil-driver type and software with the supplier. Not all historic variants and pin assignments are documented here.

Complete connector assignmentsAll 121 labelled positions follow the SBD 9A9 connection list, issue N2, BOM 1.010 onward and software 9A9ad400 onward. The table reproduces the source's pin titles; “not named” indicates an empty title, not necessarily an unused circuit. Consult the original for output ratings, pull-ups, individual notes and connector orientation. Assigned functions depend on calibration and particular hardware.The source describes different functions on earlier BOM revisions at A032, A051, A070 and B102–B105. This table is scoped to BOM 1.010 onward and must not be used to infer an earlier revision.PinManufacturer connection-list titleA001GroundA002GroundA003ECU Permanent 12V SupplyA00412V SwitchA00512V SwitchA006Air Charge Pump RelayA007Oil TempA008Injector Drive D (4th to fire)A009Anti Lag SignalA010Baro SignalA0115Va2A012Injector Drive H (8th to fire)A013Narrow Band Oxygen Sensor 1A014Rad Fan Relay 2A015Lambda1 RA016Cam ReturnA017EGT SignalA018Air Temp SignalA019Engine Oil Pressure SignalA020Shift Up SolenoidA021Ignition Drive E (5th to fire)A022Ignition Drive F (6th to fire)A023Ignition Drive G (7th to fire)A024Ignition Drive H (8th to fire)A025Shift LightA026Launch SignalA027Injector Drive C (3rd to fire)A028Not named in sourceA029Lambda1 NA0305Va2A031Injector Drive G (7th to fire)A0320va (YG)A033Not named in sourceA034Fuel Pressure SignalA035Cam SupplyA036MAP 2 SignalA037Powershift SignalA038TPS2 SignalA039Not named in sourceA040Egas2 Motor Drive -A041Egas2 Motor Drive +A042Lambda Sensor 2 HeaterA043Lambda Sensor 1 HeaterA044Shift Light 2A045Pedal A SignalA046Injector Drive B (2nd to fire)A047TPS1 SignalA048Lambda1 VGA049Lambda1 PA050Injector Drive F (6th to fire)A0510Va (ZG)A052Rad Fan Relay 1A053Gearbox SignalA054Cam 2 SignalA055Pedal B SignalA056Engine Stop SignalA057TPS4 SignalA058Down Shift SolenoidA059Egas1 Motor Drive -A060Egas1 Motor Drive +A061Varable Cam 2 DriveA062Varable Cam 1 DriveA063Neutral LightA064Not named in sourceA065Injector Drive A (1st to fire)A066MAP SignalA067Water Temp SignalA068Not named in sourceA069Injector Drive E (5th to fire)A0700Va (XG)A071Throttle Blip SolenoidA072Narrow Band Oxygen Sensor 2A073Cam1 SignalA074TPS3 SignalA075Not named in sourceA076Nitrous Input PinA077Not named in sourceA078Not named in sourceA079Wastegate DriveA080PWM Water PumpA081Tachometer DriveB082Not named in sourceB083Lambda2 PB084Lambda2 RB085Knock1 SignalB086Wheelspeed 1B087Wheelspeed 2B088CAN 2 HB089CAN HB090Fuel Pump RelayB091Lambda2 NB092Lambda2 VGB093Knock1 ReturnB094Wheelspeed 3B095Wheelspeed 4B096CAN 2 LB097CAN LB098Engine Stop OutputB0995Va1B100Crank SignalB101Knock 2 SignalB102WS1 Ret 0VB103WS2 Ret 0VB104WS3 Ret 0VB105WS4 Ret 0VB106PWR Hold RelayB1075Va1B108Crank ReturnB109Knock 2 ReturnB110Ignition Drive A (1st to fire)B111Ignition Drive B (2nd to fire)B112Ignition Drive C (3rd to fire)B113Ignition Drive D (4th to fire)B114HSD Battery +B115HSD Battery +B116Starter SolenoidB117Ignition OutputB118Rad Fan 1 HSDB119Fuel PumpB120Engine Stop OutputB121PWM Water PumpSelected connector pinsThe following is a partial reference for 9A9 issue N2; BOM 1.010 or later and software 9A9ad400 onward. See the complete SBD connection list for every pin, electrical rating and application-specific function. Earlier hardware can differ.PinDocumented functionA001–A002GroundA003Permanent ECU 12 VA004–A005Switched 12 VA008Injector DA012Injector HA027Injector CA031Injector GA046Injector BA050Injector FA065Injector AA069Injector EB088 / B096CAN 2 high / lowB089 / B097CAN high / lowB100 / B108Crank signal / returnB110–B113Ignition drives A–D

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 2: MBE 9A9

The 9A9 is an MBE fuel-injection ECU for up to eight cylinders. SBD describes twin wideband lambda inputs and two CAN buses; pinout, sensor and driver suitability depends on the exact hardware and software. Source and identification.

Wiring and pinout

Model wiring documentation: Issue N2, BOM1-010 onward only; obtain the matching diagram for other builds. Check connector view, wiring harness, ECU part number and installed calibration before connecting power. Programmable input and output functions depend on the map and software.

Configuration and support

For programmable SBD-supplied ECUs, Easimap is used to inspect and change maps, subject to the interface and access of the actual ECU. Some vehicle-manufacturer supplied units are locked; SBD’s FAQ warns against attempting downloads to locked ECUs. Do not assume that a serial ECU map or harness transfers directly to a newer CAN unit.

Evidence limits

Verify the build, trigger inputs, coil-driver type and software with the supplier. Not all historic variants and pin assignments are documented here.

Selected connector pins

The following is a partial reference for 9A9 issue N2; BOM 1.010 or later and software 9A9ad400 onward. See the complete SBD connection list for every pin, electrical rating and application-specific function. Earlier hardware can differ.

PinDocumented function
A001–A002Ground
A003Permanent ECU 12 V
A004–A005Switched 12 V
A008Injector D
A012Injector H
A027Injector C
A031Injector G
A046Injector B
A050Injector F
A065Injector A
A069Injector E
B088 / B096CAN 2 high / low
B089 / B097CAN high / low
B100 / B108Crank signal / return
B110–B113Ignition drives A–D
Revision 3: MBE 9A9

The 9A9 is an MBE fuel-injection ECU for up to eight cylinders. SBD describes twin wideband lambda inputs and two CAN buses; pinout, sensor and driver suitability depends on the exact hardware and software. Source and identification.

Wiring and pinout

Model wiring documentation: Issue N2, BOM1-010 onward only; obtain the matching diagram for other builds. Check connector view, wiring harness, ECU part number and installed calibration before connecting power. Programmable input and output functions depend on the map and software.

Configuration and support

For programmable SBD-supplied ECUs, Easimap is used to inspect and change maps, subject to the interface and access of the actual ECU. Some vehicle-manufacturer supplied units are locked; SBD’s FAQ warns against attempting downloads to locked ECUs. Do not assume that a serial ECU map or harness transfers directly to a newer CAN unit.

Evidence limits

Verify the build, trigger inputs, coil-driver type and software with the supplier. Not all historic variants and pin assignments are documented here.

Complete connector assignments

All 121 labelled positions follow the SBD 9A9 connection list, issue N2, BOM 1.010 onward and software 9A9ad400 onward. The table reproduces the source's pin titles; “not named” indicates an empty title, not necessarily an unused circuit. Consult the original for output ratings, pull-ups, individual notes and connector orientation. Assigned functions depend on calibration and particular hardware.

The source describes different functions on earlier BOM revisions at A032, A051, A070 and B102–B105. This table is scoped to BOM 1.010 onward and must not be used to infer an earlier revision.

PinManufacturer connection-list title
A001Ground
A002Ground
A003ECU Permanent 12V Supply
A00412V Switch
A00512V Switch
A006Air Charge Pump Relay
A007Oil Temp
A008Injector Drive D (4th to fire)
A009Anti Lag Signal
A010Baro Signal
A0115Va2
A012Injector Drive H (8th to fire)
A013Narrow Band Oxygen Sensor 1
A014Rad Fan Relay 2
A015Lambda1 R
A016Cam Return
A017EGT Signal
A018Air Temp Signal
A019Engine Oil Pressure Signal
A020Shift Up Solenoid
A021Ignition Drive E (5th to fire)
A022Ignition Drive F (6th to fire)
A023Ignition Drive G (7th to fire)
A024Ignition Drive H (8th to fire)
A025Shift Light
A026Launch Signal
A027Injector Drive C (3rd to fire)
A028Not named in source
A029Lambda1 N
A0305Va2
A031Injector Drive G (7th to fire)
A0320va (YG)
A033Not named in source
A034Fuel Pressure Signal
A035Cam Supply
A036MAP 2 Signal
A037Powershift Signal
A038TPS2 Signal
A039Not named in source
A040Egas2 Motor Drive -
A041Egas2 Motor Drive +
A042Lambda Sensor 2 Heater
A043Lambda Sensor 1 Heater
A044Shift Light 2
A045Pedal A Signal
A046Injector Drive B (2nd to fire)
A047TPS1 Signal
A048Lambda1 VG
A049Lambda1 P
A050Injector Drive F (6th to fire)
A0510Va (ZG)
A052Rad Fan Relay 1
A053Gearbox Signal
A054Cam 2 Signal
A055Pedal B Signal
A056Engine Stop Signal
A057TPS4 Signal
A058Down Shift Solenoid
A059Egas1 Motor Drive -
A060Egas1 Motor Drive +
A061Varable Cam 2 Drive
A062Varable Cam 1 Drive
A063Neutral Light
A064Not named in source
A065Injector Drive A (1st to fire)
A066MAP Signal
A067Water Temp Signal
A068Not named in source
A069Injector Drive E (5th to fire)
A0700Va (XG)
A071Throttle Blip Solenoid
A072Narrow Band Oxygen Sensor 2
A073Cam1 Signal
A074TPS3 Signal
A075Not named in source
A076Nitrous Input Pin
A077Not named in source
A078Not named in source
A079Wastegate Drive
A080PWM Water Pump
A081Tachometer Drive
B082Not named in source
B083Lambda2 P
B084Lambda2 R
B085Knock1 Signal
B086Wheelspeed 1
B087Wheelspeed 2
B088CAN 2 H
B089CAN H
B090Fuel Pump Relay
B091Lambda2 N
B092Lambda2 VG
B093Knock1 Return
B094Wheelspeed 3
B095Wheelspeed 4
B096CAN 2 L
B097CAN L
B098Engine Stop Output
B0995Va1
B100Crank Signal
B101Knock 2 Signal
B102WS1 Ret 0V
B103WS2 Ret 0V
B104WS3 Ret 0V
B105WS4 Ret 0V
B106PWR Hold Relay
B1075Va1
B108Crank Return
B109Knock 2 Return
B110Ignition Drive A (1st to fire)
B111Ignition Drive B (2nd to fire)
B112Ignition Drive C (3rd to fire)
B113Ignition Drive D (4th to fire)
B114HSD Battery +
B115HSD Battery +
B116Starter Solenoid
B117Ignition Output
B118Rad Fan 1 HSD
B119Fuel Pump
B120Engine Stop Output
B121PWM Water Pump