Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Engine ECU
Parent
MS3Pro PNP
Applies to
MS3Pro PNP
Tool groups
None
Manufacturers
None

Changes from revision 1 to revision 3

Removed text is struck through; added text is highlighted.

MSPNP-Pro SW0205 Subaru WRX version shown as a family illustration; this application has its own case and connector layout. Image: AMP Engine Management, reproduced with permission.

MSPNP-Pro EECV-8PM is a vehicle-specific MS3Pro-based plug-in engine management ECU. The manufacturer’s model-specific installation guide lists the following application: 1999–2003 Mazda Protegé 1.6, 1.8, 2.0 and 2.0T, manual transmission, as listed by the guide. Fitment depends on the original ECU connector, engine, harness and market; confirm the exact part number before installation.

Application and installation

The manufacturer’s document title and index say EECV-8PM, but the opening model identifier says EECV-4PM. Treat the code as unresolved and verify the label and fitment with the supplier. Plug-in does not mean every optional feature is prewired: follow the relevant guide for setup, sensors, jumpers, base tune and ignition-timing checks.

Pinout and documentation

AMP EFI EECV-8PM vehicle-specific installation and connector documentation is the primary source for this model. Check the connector orientation, version and any configurable or optional functions before wiring. Diagrams may be shown as images in the guide; this page does not substitute a pin assignment from another MSPNP model.

See the manufacturer’s ECU documentation index and firmware and base-tune index. Initial maps require verification and tuning for the particular engine.

Rear options connector — A–ZTranscribed from this application's AMP EFI installation guide. These are the rear options connections; they are not the complete factory vehicle connector pinout. Verify orientation, exact ECU variant, electrical limits and software configuration before wiring.PinFunctionDefault or note in sourceAAnalog sensor groundSensor returnB5 V VrefFused at 250 mACAIN2Fuel level sensor; duplicates main pin 63D12 V supply outFused at 250 mAEIATDuplicates main pin 39FExternal MAP sensorInternal MAP sensor defaultGEGOOptional wideband O2; duplicates main pin 60HAnalog input 1MAF sensor; duplicates main pin 88ICANL—JDFIN1 conditionedVR sensors only; duplicates main pin 58KCANH—LDFIN2 conditionedAdditional speed sensor, VR sensors onlyMDigital input 1Optional flex fuelNDigital input 4—ODigital input 2—PDFIN3—QDigital input 3A/C request switch; duplicates main pin 41RTach outInstrument cluster; duplicates main pin 48SPower ground—THigh current output 3VICS; duplicates main pin 19UHigh current output 1Condenser fan; duplicates main pins 17 and 45VHigh current output 2Duplicates main pin 82WPWM output 3A/C compressor; duplicates main pin 69XInjector output JCharge lamp; duplicates main pin 42YPWM output 2High cooling fan; duplicates main pin 46ZInjector output IHigh impedance only

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 1: MS3Pro PNP EECV-8PM — Mazda Protegé

MSPNP-Pro EECV-8PM is a vehicle-specific MS3Pro-based plug-in engine management ECU. The manufacturer’s model-specific installation guide lists the following application: 1999–2003 Mazda Protegé 1.6, 1.8, 2.0 and 2.0T, manual transmission, as listed by the guide. Fitment depends on the original ECU connector, engine, harness and market; confirm the exact part number before installation.

Application and installation

The manufacturer’s document title and index say EECV-8PM, but the opening model identifier says EECV-4PM. Treat the code as unresolved and verify the label and fitment with the supplier. Plug-in does not mean every optional feature is prewired: follow the relevant guide for setup, sensors, jumpers, base tune and ignition-timing checks.

Pinout and documentation

AMP EFI EECV-8PM vehicle-specific installation and connector documentation is the primary source for this model. Check the connector orientation, version and any configurable or optional functions before wiring. Diagrams may be shown as images in the guide; this page does not substitute a pin assignment from another MSPNP model.

See the manufacturer’s ECU documentation index and firmware and base-tune index. Initial maps require verification and tuning for the particular engine.

Revision 3: MS3Pro PNP EECV-8PM — Mazda Protegé
AMP MSPNP-Pro Subaru WRX ECU
MSPNP-Pro SW0205 Subaru WRX version shown as a family illustration; this application has its own case and connector layout. Image: AMP Engine Management, reproduced with permission.

MSPNP-Pro EECV-8PM is a vehicle-specific MS3Pro-based plug-in engine management ECU. The manufacturer’s model-specific installation guide lists the following application: 1999–2003 Mazda Protegé 1.6, 1.8, 2.0 and 2.0T, manual transmission, as listed by the guide. Fitment depends on the original ECU connector, engine, harness and market; confirm the exact part number before installation.

Application and installation

The manufacturer’s document title and index say EECV-8PM, but the opening model identifier says EECV-4PM. Treat the code as unresolved and verify the label and fitment with the supplier. Plug-in does not mean every optional feature is prewired: follow the relevant guide for setup, sensors, jumpers, base tune and ignition-timing checks.

Pinout and documentation

AMP EFI EECV-8PM vehicle-specific installation and connector documentation is the primary source for this model. Check the connector orientation, version and any configurable or optional functions before wiring. Diagrams may be shown as images in the guide; this page does not substitute a pin assignment from another MSPNP model.

See the manufacturer’s ECU documentation index and firmware and base-tune index. Initial maps require verification and tuning for the particular engine.

Rear options connector — A–Z

Transcribed from this application's AMP EFI installation guide. These are the rear options connections; they are not the complete factory vehicle connector pinout. Verify orientation, exact ECU variant, electrical limits and software configuration before wiring.

PinFunctionDefault or note in source
AAnalog sensor groundSensor return
B5 V VrefFused at 250 mA
CAIN2Fuel level sensor; duplicates main pin 63
D12 V supply outFused at 250 mA
EIATDuplicates main pin 39
FExternal MAP sensorInternal MAP sensor default
GEGOOptional wideband O2; duplicates main pin 60
HAnalog input 1MAF sensor; duplicates main pin 88
ICANL—
JDFIN1 conditionedVR sensors only; duplicates main pin 58
KCANH—
LDFIN2 conditionedAdditional speed sensor, VR sensors only
MDigital input 1Optional flex fuel
NDigital input 4—
ODigital input 2—
PDFIN3—
QDigital input 3A/C request switch; duplicates main pin 41
RTach outInstrument cluster; duplicates main pin 48
SPower ground—
THigh current output 3VICS; duplicates main pin 19
UHigh current output 1Condenser fan; duplicates main pins 17 and 45
VHigh current output 2Duplicates main pin 82
WPWM output 3A/C compressor; duplicates main pin 69
XInjector output JCharge lamp; duplicates main pin 42
YPWM output 2High cooling fan; duplicates main pin 46
ZInjector output IHigh impedance only