Removed text is struck through; added text is highlighted.
MSPNP-Pro SW0205 Subaru WRX version shown as a family illustration; this application has its own case and connector layout. Image: AMP Engine Management, reproduced with permission.
MSPNP-Pro E369395 is a vehicle-specific MS3Pro-based plug-in engine management ECU. The manufacturer’s model-specific installation guide lists the following application: 1993–1995 BMW E36 325i, 328i and M3 as listed in the manufacturer’s guide. Fitment depends on the original ECU connector, engine, harness and market; confirm the exact part number before installation.
Application and installation
Confirm the actual engine and ECU connector, as the guide lists several models across the date range. Plug-in does not mean every optional feature is prewired: follow the relevant guide for setup, sensors, jumpers, base tune and ignition-timing checks.
Pinout and documentation
AMP EFI E369395 vehicle-specific installation and connector documentation is the primary source for this model. Check the connector orientation, version and any configurable or optional functions before wiring. Diagrams may be shown as images in the guide; this page does not substitute a pin assignment from another MSPNP model.
See the manufacturer’s ECU documentation index and firmware and base-tune index. Initial maps require verification and tuning for the particular engine.
Rear options connectors by hardware versionThese tables follow the AMP EFI application guide. The guide labels the 26- and 22-position tables V2 and separately illustrates a 20-position options connector. Identify the installed ECU and connector generation before wiring; these are rear options, not the complete original BMW main connector.V2 connector 1 — 26 positionsPinFunctionDefault or notes1ASpark out ACoil A, cylinder 1; logic-level smart coil1BSpark out BCoil B, cylinder 5; logic-level smart coil1CSpark out CCoil C, cylinder 3; logic-level smart coil1DSpark out DCoil D, cylinder 6; logic-level smart coil1ESpark out ECoil E, cylinder 2; logic-level smart coil1FSpark out FCoil F, cylinder 4; logic-level smart coil1GInjector out G—1HInjector out H—1IDigital in 2—1JDigital in 3—1KDigital in 12 V—1LIATAftermarket IAT; disconnect OE IAT if used1MDigital frequency in 1—1NDigital frequency in 2—1OAnalog in 1Assigned MAF; disconnect MAF to repurpose1PAnalog in 2General-purpose analog input1QAnalog in 3General-purpose analog input1RAnalog in 4General-purpose analog input1SAnalog in 5General-purpose analog input1TAnalog in 6General-purpose analog input1UAnalog in 7General-purpose analog input1VAnalog in 8 / EGOWideband sensor input; can repurpose1WCAN H120 ohm termination onboard1XCAN L120 ohm termination onboard1Y5 V VREF outSensor 5 V power, internally fused 0.25 A1ZSensor ground—V2 connector 2 — 22 positionsPinFunctionDefault or notes2A12 V+ outIgnition-switched; 0.25 A fuse; relay control only, not supply power2BDigital input 1 / FLEXAvailable flex sensor input2CIAC1A—2DIAC1B—2EIAC2A—2FIAC2B—2GInjector out I—2HInjector out J—2ITach outFactory dashboard tachometer2JHigh current out 1—2KHigh current out 2—2LHigh current out 3—2MPWM out 2Idle valve; IAC close2NPWM out 3VANOS camshaft control2OPWM out 4—2PPWM out 5—2QUnused—2RUnused—2SUnused—2TUnused—2UUnused—2VUnused—20-position options connectorPinFunctionDefault or notes1High current 1—2High current 2—3High current 3—4Injector GHigh impedance only5Injector HHigh impedance only6CMP+Hall only; internal pull-up to 5 V7Vref +5 V—8External MAPMove internal jumper9Analog input 1MAF10EGO—11Digital input 4—12Digital input 2—13Digital input 1—14CANL—15CANH—16DFIN3Wheel speed 2, VR+ only17DFIN2Wheel speed 1, VR+ only18Analog input 2—19IAT—20Sensor return—The V2 source marks pins 1A–1F, 1W–1Z, 2A–2B and 2S–2V large and the remainder small. Check the original for views, electrical limits and jumper settings.
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 1: MS3Pro PNP E369395 — BMW E36 1993–1995
MSPNP-Pro E369395 is a vehicle-specific MS3Pro-based plug-in engine management ECU. The manufacturer’s model-specific installation guide lists the following application: 1993–1995 BMW E36 325i, 328i and M3 as listed in the manufacturer’s guide. Fitment depends on the original ECU connector, engine, harness and market; confirm the exact part number before installation.
Application and installation
Confirm the actual engine and ECU connector, as the guide lists several models across the date range. Plug-in does not mean every optional feature is prewired: follow the relevant guide for setup, sensors, jumpers, base tune and ignition-timing checks.
Pinout and documentation
AMP EFI E369395 vehicle-specific installation and connector documentation is the primary source for this model. Check the connector orientation, version and any configurable or optional functions before wiring. Diagrams may be shown as images in the guide; this page does not substitute a pin assignment from another MSPNP model.
Revision 3: MS3Pro PNP E369395 — BMW E36 1993–1995MSPNP-Pro SW0205 Subaru WRX version shown as a family illustration; this application has its own case and connector layout. Image: AMP Engine Management, reproduced with permission.
MSPNP-Pro E369395 is a vehicle-specific MS3Pro-based plug-in engine management ECU. The manufacturer’s model-specific installation guide lists the following application: 1993–1995 BMW E36 325i, 328i and M3 as listed in the manufacturer’s guide. Fitment depends on the original ECU connector, engine, harness and market; confirm the exact part number before installation.
Application and installation
Confirm the actual engine and ECU connector, as the guide lists several models across the date range. Plug-in does not mean every optional feature is prewired: follow the relevant guide for setup, sensors, jumpers, base tune and ignition-timing checks.
Pinout and documentation
AMP EFI E369395 vehicle-specific installation and connector documentation is the primary source for this model. Check the connector orientation, version and any configurable or optional functions before wiring. Diagrams may be shown as images in the guide; this page does not substitute a pin assignment from another MSPNP model.
These tables follow the AMP EFI application guide. The guide labels the 26- and 22-position tables V2 and separately illustrates a 20-position options connector. Identify the installed ECU and connector generation before wiring; these are rear options, not the complete original BMW main connector.
V2 connector 1 — 26 positions
Pin
Function
Default or notes
1A
Spark out A
Coil A, cylinder 1; logic-level smart coil
1B
Spark out B
Coil B, cylinder 5; logic-level smart coil
1C
Spark out C
Coil C, cylinder 3; logic-level smart coil
1D
Spark out D
Coil D, cylinder 6; logic-level smart coil
1E
Spark out E
Coil E, cylinder 2; logic-level smart coil
1F
Spark out F
Coil F, cylinder 4; logic-level smart coil
1G
Injector out G
—
1H
Injector out H
—
1I
Digital in 2
—
1J
Digital in 3
—
1K
Digital in 12 V
—
1L
IAT
Aftermarket IAT; disconnect OE IAT if used
1M
Digital frequency in 1
—
1N
Digital frequency in 2
—
1O
Analog in 1
Assigned MAF; disconnect MAF to repurpose
1P
Analog in 2
General-purpose analog input
1Q
Analog in 3
General-purpose analog input
1R
Analog in 4
General-purpose analog input
1S
Analog in 5
General-purpose analog input
1T
Analog in 6
General-purpose analog input
1U
Analog in 7
General-purpose analog input
1V
Analog in 8 / EGO
Wideband sensor input; can repurpose
1W
CAN H
120 ohm termination onboard
1X
CAN L
120 ohm termination onboard
1Y
5 V VREF out
Sensor 5 V power, internally fused 0.25 A
1Z
Sensor ground
—
V2 connector 2 — 22 positions
Pin
Function
Default or notes
2A
12 V+ out
Ignition-switched; 0.25 A fuse; relay control only, not supply power
2B
Digital input 1 / FLEX
Available flex sensor input
2C
IAC1A
—
2D
IAC1B
—
2E
IAC2A
—
2F
IAC2B
—
2G
Injector out I
—
2H
Injector out J
—
2I
Tach out
Factory dashboard tachometer
2J
High current out 1
—
2K
High current out 2
—
2L
High current out 3
—
2M
PWM out 2
Idle valve; IAC close
2N
PWM out 3
VANOS camshaft control
2O
PWM out 4
—
2P
PWM out 5
—
2Q
Unused
—
2R
Unused
—
2S
Unused
—
2T
Unused
—
2U
Unused
—
2V
Unused
—
20-position options connector
Pin
Function
Default or notes
1
High current 1
—
2
High current 2
—
3
High current 3
—
4
Injector G
High impedance only
5
Injector H
High impedance only
6
CMP+
Hall only; internal pull-up to 5 V
7
Vref +5 V
—
8
External MAP
Move internal jumper
9
Analog input 1
MAF
10
EGO
—
11
Digital input 4
—
12
Digital input 2
—
13
Digital input 1
—
14
CANL
—
15
CANH
—
16
DFIN3
Wheel speed 2, VR+ only
17
DFIN2
Wheel speed 1, VR+ only
18
Analog input 2
—
19
IAT
—
20
Sensor return
—
The V2 source marks pins 1A–1F, 1W–1Z, 2A–2B and 2S–2V large and the remainder small. Check the original for views, electrical limits and jumper settings.