Page organisation in this revision
- Page type
- Reference hub
- Subject
- Engine ECU
- Parent
- MBE Systems standalone ECUs
- Applies to
- No ECU-specific applicability
- Tool groups
- None
- Manufacturers
- None
Changes from revision 2 to revision 3
Removed text is struck through; added text is highlighted.
SBD lists the 9M8 for sequential fuelling of engines up to eight cylinders using high-impedance injectors. Its product page links the 9A8 wiring sheet; verify the actual build and pin functions before wiring. Source and identification.
Wiring and pinout
Model wiring documentation: 9A8 issue F; linked from SBD’s 9M8 listing. Check connector view, wiring harness, ECU part number and installed calibration before connecting power. Programmable input and output functions depend on the map and software.
Configuration and support
For programmable SBD-supplied ECUs, Easimap is used to inspect and change maps, subject to the interface and access of the actual ECU. Some vehicle-manufacturer supplied units are locked; SBD’s FAQ warns against attempting downloads to locked ECUs. Do not assume that a serial ECU map or harness transfers directly to a newer CAN unit.
Evidence limits
Verify the build, trigger inputs, coil-driver type and software with the supplier. Not all historic variants and pin assignments are documented here.
J2 Delphi 36-way connector — issue F
From SBD's connector list. This is the general-function column; issue F also gives an I4 staged-injector column, which must be checked for that configuration. Pin numbers identify connector cavities; consult the diagram for the view. Programmable pins depend on the installed map.
PinGeneral function1Injector D (4th to fire)2Water temperature3Air temperature45VA reference50VA6Power ground7Power ground8CAN low9CAN high10Permanent 12 V supply11Crank return12Crank signal13Switched 12 V supply14Injector A (1st to fire)15Ignition (4th to fire)16Programmable low-side output17Programmable low-side output18Ignition (2nd to fire)19Programmable input20Throttle position21MAP22Injector E (5th to fire)23Injector F (6th to fire)24Injector G (7th to fire)25Programmable input/output26Injector C (3rd to fire)27Programmable input28Barometric pressure29Lambda30Cam signal31Injector H (8th to fire)32Injector B (2nd to fire)33Programmable low-side output34Programmable low-side output35Ignition (3rd to fire)36Ignition (1st to fire)
Four-cylinder staged-injector connector assignmentsThe I4 column in SBD’s 9A8 issue F connector list identifies separate upper and lower injector assignments for the 36-way connector. SBD links that list from its 9M8 product page. Injector order is firing order as shown in the source, not necessarily cylinder numbering. Confirm the exact ECU build, wiring configuration, programmable functions, source connector view and output ratings before connecting.PinI4 function1Lower injector D (4th to fire)2Water temperature3Air temperature45 V analogue reference5Analogue ground (0VA)6Power ground7Power ground8CAN low9CAN high10Permanent battery 12 V11Crank return12Crank signal13Ignition-switched 12 V14Lower injector A (1st to fire)15Ignition (4th to fire)16Programmable low-side output17Programmable low-side output18Ignition (2nd to fire)19Programmable input20Throttle position sensor21Manifold pressure sensor22Upper injector E (1st to fire)23Upper injector F (2nd to fire)24Upper injector G (3rd to fire)25Programmable input/output26Lower injector C (3rd to fire)27Programmable input28Barometric pressure29Lambda30Cam signal31Upper injector H (4th to fire)32Lower injector B (2nd to fire)33Programmable low-side output34Programmable low-side output35Ignition (3rd to fire)36Ignition (1st to fire)
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 2: MBE 9M8
SBD lists the 9M8 for sequential fuelling of engines up to eight cylinders using high-impedance injectors. Its product page links the 9A8 wiring sheet; verify the actual build and pin functions before wiring. Source and identification.
Wiring and pinout
Model wiring documentation: 9A8 issue F; linked from SBD’s 9M8 listing. Check connector view, wiring harness, ECU part number and installed calibration before connecting power. Programmable input and output functions depend on the map and software.
Configuration and support
For programmable SBD-supplied ECUs, Easimap is used to inspect and change maps, subject to the interface and access of the actual ECU. Some vehicle-manufacturer supplied units are locked; SBD’s FAQ warns against attempting downloads to locked ECUs. Do not assume that a serial ECU map or harness transfers directly to a newer CAN unit.
Evidence limits
Verify the build, trigger inputs, coil-driver type and software with the supplier. Not all historic variants and pin assignments are documented here.
J2 Delphi 36-way connector — issue F
From SBD's connector list. This is the general-function column; issue F also gives an I4 staged-injector column, which must be checked for that configuration. Pin numbers identify connector cavities; consult the diagram for the view. Programmable pins depend on the installed map.
| Pin | General function |
|---|
| 1 | Injector D (4th to fire) |
| 2 | Water temperature |
| 3 | Air temperature |
| 4 | 5VA reference |
| 5 | 0VA |
| 6 | Power ground |
| 7 | Power ground |
| 8 | CAN low |
| 9 | CAN high |
| 10 | Permanent 12 V supply |
| 11 | Crank return |
| 12 | Crank signal |
| 13 | Switched 12 V supply |
| 14 | Injector A (1st to fire) |
| 15 | Ignition (4th to fire) |
| 16 | Programmable low-side output |
| 17 | Programmable low-side output |
| 18 | Ignition (2nd to fire) |
| 19 | Programmable input |
| 20 | Throttle position |
| 21 | MAP |
| 22 | Injector E (5th to fire) |
| 23 | Injector F (6th to fire) |
| 24 | Injector G (7th to fire) |
| 25 | Programmable input/output |
| 26 | Injector C (3rd to fire) |
| 27 | Programmable input |
| 28 | Barometric pressure |
| 29 | Lambda |
| 30 | Cam signal |
| 31 | Injector H (8th to fire) |
| 32 | Injector B (2nd to fire) |
| 33 | Programmable low-side output |
| 34 | Programmable low-side output |
| 35 | Ignition (3rd to fire) |
| 36 | Ignition (1st to fire) |
Revision 3: MBE 9M8
SBD lists the 9M8 for sequential fuelling of engines up to eight cylinders using high-impedance injectors. Its product page links the 9A8 wiring sheet; verify the actual build and pin functions before wiring. Source and identification.
Wiring and pinout
Model wiring documentation: 9A8 issue F; linked from SBD’s 9M8 listing. Check connector view, wiring harness, ECU part number and installed calibration before connecting power. Programmable input and output functions depend on the map and software.
Configuration and support
For programmable SBD-supplied ECUs, Easimap is used to inspect and change maps, subject to the interface and access of the actual ECU. Some vehicle-manufacturer supplied units are locked; SBD’s FAQ warns against attempting downloads to locked ECUs. Do not assume that a serial ECU map or harness transfers directly to a newer CAN unit.
Evidence limits
Verify the build, trigger inputs, coil-driver type and software with the supplier. Not all historic variants and pin assignments are documented here.
J2 Delphi 36-way connector — issue F
From SBD's connector list. This is the general-function column; issue F also gives an I4 staged-injector column, which must be checked for that configuration. Pin numbers identify connector cavities; consult the diagram for the view. Programmable pins depend on the installed map.
| Pin | General function |
|---|
| 1 | Injector D (4th to fire) |
| 2 | Water temperature |
| 3 | Air temperature |
| 4 | 5VA reference |
| 5 | 0VA |
| 6 | Power ground |
| 7 | Power ground |
| 8 | CAN low |
| 9 | CAN high |
| 10 | Permanent 12 V supply |
| 11 | Crank return |
| 12 | Crank signal |
| 13 | Switched 12 V supply |
| 14 | Injector A (1st to fire) |
| 15 | Ignition (4th to fire) |
| 16 | Programmable low-side output |
| 17 | Programmable low-side output |
| 18 | Ignition (2nd to fire) |
| 19 | Programmable input |
| 20 | Throttle position |
| 21 | MAP |
| 22 | Injector E (5th to fire) |
| 23 | Injector F (6th to fire) |
| 24 | Injector G (7th to fire) |
| 25 | Programmable input/output |
| 26 | Injector C (3rd to fire) |
| 27 | Programmable input |
| 28 | Barometric pressure |
| 29 | Lambda |
| 30 | Cam signal |
| 31 | Injector H (8th to fire) |
| 32 | Injector B (2nd to fire) |
| 33 | Programmable low-side output |
| 34 | Programmable low-side output |
| 35 | Ignition (3rd to fire) |
| 36 | Ignition (1st to fire) |
Four-cylinder staged-injector connector assignments
The I4 column in SBD’s 9A8 issue F connector list identifies separate upper and lower injector assignments for the 36-way connector. SBD links that list from its 9M8 product page. Injector order is firing order as shown in the source, not necessarily cylinder numbering. Confirm the exact ECU build, wiring configuration, programmable functions, source connector view and output ratings before connecting.
| Pin | I4 function |
|---|
| 1 | Lower injector D (4th to fire) |
| 2 | Water temperature |
| 3 | Air temperature |
| 4 | 5 V analogue reference |
| 5 | Analogue ground (0VA) |
| 6 | Power ground |
| 7 | Power ground |
| 8 | CAN low |
| 9 | CAN high |
| 10 | Permanent battery 12 V |
| 11 | Crank return |
| 12 | Crank signal |
| 13 | Ignition-switched 12 V |
| 14 | Lower injector A (1st to fire) |
| 15 | Ignition (4th to fire) |
| 16 | Programmable low-side output |
| 17 | Programmable low-side output |
| 18 | Ignition (2nd to fire) |
| 19 | Programmable input |
| 20 | Throttle position sensor |
| 21 | Manifold pressure sensor |
| 22 | Upper injector E (1st to fire) |
| 23 | Upper injector F (2nd to fire) |
| 24 | Upper injector G (3rd to fire) |
| 25 | Programmable input/output |
| 26 | Lower injector C (3rd to fire) |
| 27 | Programmable input |
| 28 | Barometric pressure |
| 29 | Lambda |
| 30 | Cam signal |
| 31 | Upper injector H (4th to fire) |
| 32 | Lower injector B (2nd to fire) |
| 33 | Programmable low-side output |
| 34 | Programmable low-side output |
| 35 | Ignition (3rd to fire) |
| 36 | Ignition (1st to fire) |