Page organisation in this revision
- Page type
- Reference hub
- Subject
- Engine ECU
- Parent
- MBE Systems standalone ECUs
- Applies to
- No ECU-specific applicability
- Tool groups
- None
- Manufacturers
- None
Changes from revision 1 to revision 2
Removed text is struck through; added text is highlighted.
The 9A4 is a four-cylinder CAN-based fuel-injection ECU. SBD says its successor 9M4 uses the same pinout and instruction sheets. The 9A4 has one CAN bus, according to the SBD CAN setup guide. Source and identification.
Wiring and pinout
Model wiring documentation: J2 Delphi 36-way, issue F. Check connector view, wiring harness, ECU part number and installed calibration before connecting power. Programmable input and output functions depend on the map and software.
Configuration and support
For programmable SBD-supplied ECUs, Easimap is used to inspect and change maps, subject to the interface and access of the actual ECU. Some vehicle-manufacturer supplied units are locked; SBD’s FAQ warns against attempting downloads to locked ECUs. Do not assume that a serial ECU map or harness transfers directly to a newer CAN unit.
Evidence limits
Verify the build, trigger inputs, coil-driver type and software with the supplier. Not all historic variants and pin assignments are documented here.
J2 Delphi 36-way connector — issue FFrom SBD's connector list. SBD confirms this 9A4 issue F sheet is used for the 9M4. Pin numbers identify connector cavities; consult the diagram for the view. Programmable pins depend on the installed map.PinGeneral function1Injector D (4th to fire)2Water temperature3Air temperature45VA reference50VA6Power ground7Power ground8CAN low9CAN high10Permanent 12 V supply11Crank return12Crank signal13Switched 12 V supply14Injector A (1st to fire)15Ignition D (4th to fire)16Programmable low-side output17Programmable low-side output18Ignition B (2nd to fire)19Programmable input20Throttle position21MAP225VA reference230VA240VA25Programmable input/output26Injector C (3rd to fire)27Programmable input28Barometric pressure29Lambda30Cam signal31Cam return32Injector B (2nd to fire)33Programmable low-side output34Programmable low-side output35Ignition C (3rd to fire)36Ignition A (1st to fire)
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 1: MBE 9A4
The 9A4 is a four-cylinder CAN-based fuel-injection ECU. SBD says its successor 9M4 uses the same pinout and instruction sheets. The 9A4 has one CAN bus, according to the SBD CAN setup guide. Source and identification.
Wiring and pinout
Model wiring documentation: J2 Delphi 36-way, issue F. Check connector view, wiring harness, ECU part number and installed calibration before connecting power. Programmable input and output functions depend on the map and software.
Configuration and support
For programmable SBD-supplied ECUs, Easimap is used to inspect and change maps, subject to the interface and access of the actual ECU. Some vehicle-manufacturer supplied units are locked; SBD’s FAQ warns against attempting downloads to locked ECUs. Do not assume that a serial ECU map or harness transfers directly to a newer CAN unit.
Evidence limits
Verify the build, trigger inputs, coil-driver type and software with the supplier. Not all historic variants and pin assignments are documented here.
Revision 2: MBE 9A4
The 9A4 is a four-cylinder CAN-based fuel-injection ECU. SBD says its successor 9M4 uses the same pinout and instruction sheets. The 9A4 has one CAN bus, according to the SBD CAN setup guide. Source and identification.
Wiring and pinout
Model wiring documentation: J2 Delphi 36-way, issue F. Check connector view, wiring harness, ECU part number and installed calibration before connecting power. Programmable input and output functions depend on the map and software.
Configuration and support
For programmable SBD-supplied ECUs, Easimap is used to inspect and change maps, subject to the interface and access of the actual ECU. Some vehicle-manufacturer supplied units are locked; SBD’s FAQ warns against attempting downloads to locked ECUs. Do not assume that a serial ECU map or harness transfers directly to a newer CAN unit.
Evidence limits
Verify the build, trigger inputs, coil-driver type and software with the supplier. Not all historic variants and pin assignments are documented here.
J2 Delphi 36-way connector — issue F
From SBD's connector list. SBD confirms this 9A4 issue F sheet is used for the 9M4. Pin numbers identify connector cavities; consult the diagram for the view. Programmable pins depend on the installed map.
| Pin | General function |
|---|
| 1 | Injector D (4th to fire) |
| 2 | Water temperature |
| 3 | Air temperature |
| 4 | 5VA reference |
| 5 | 0VA |
| 6 | Power ground |
| 7 | Power ground |
| 8 | CAN low |
| 9 | CAN high |
| 10 | Permanent 12 V supply |
| 11 | Crank return |
| 12 | Crank signal |
| 13 | Switched 12 V supply |
| 14 | Injector A (1st to fire) |
| 15 | Ignition D (4th to fire) |
| 16 | Programmable low-side output |
| 17 | Programmable low-side output |
| 18 | Ignition B (2nd to fire) |
| 19 | Programmable input |
| 20 | Throttle position |
| 21 | MAP |
| 22 | 5VA reference |
| 23 | 0VA |
| 24 | 0VA |
| 25 | Programmable input/output |
| 26 | Injector C (3rd to fire) |
| 27 | Programmable input |
| 28 | Barometric pressure |
| 29 | Lambda |
| 30 | Cam signal |
| 31 | Cam return |
| 32 | Injector B (2nd to fire) |
| 33 | Programmable low-side output |
| 34 | Programmable low-side output |
| 35 | Ignition C (3rd to fire) |
| 36 | Ignition A (1st to fire) |