Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
Syvecs Standalone ECUs
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Changes from revision 2 to revision 3

Removed text is struck through; added text is highlighted.

Syvecs manufacturer product photograph, reproduced with permission. Image source.

Overview and hardware

Syvecs S12 is a British engine-management ECU. Flagship V12/high-I/O ECU launched in 2014. Manufacturer lists 28 inputs, 24 port injector outputs, 12 ignition outputs, 3 full bridges, 8 extra PWM outputs, 4 knock, 2 EGT, 3 CAN, 121 pins and 6–26 V. Its detailed specification lists two NTK lambda interfaces, but a short summary says four; confirm with Syvecs. Direct injection requires compatible external hardware and software.

Compare the required injector, ignition, actuator and sensor channels with the hardware available on the actual ECU. Capabilities and configurable functions depend on firmware, hardware revision and calibration.

Wiring and pinout

Manufacturer S12 wiring guide and pinout. Use the guide's connector view and pin numbering and verify ECU hardware revision and configuration before wiring. Pin and input functions may vary by calibration or vehicle. Syvecs wiring index contains further example pinout files.

Vehicle-specific replacement kits use their own harness or carrier board. Consult the corresponding vehicle-specific Syvecs guide rather than assuming a generic schedule applies.

Complete connector pin assignmentsThese 121 pin positions, source labels and functions are taken from the Syvecs S12 wiring guide. Confirm the connector view, device settings and wiring limits in the original before wiring; channels may be configurable.PinSource labelFunction1PWRGNDEcu Ground2IGN01Ignition (20A Open Collector)3IGN02Ignition (20A Open Collector)4IGN03Ignition (20A Open Collector)5IGN04Ignition (20A Open Collector)6IN255V Analogue Input7KNOCK 4Knock Sensors8KNOCKGNDKnock Sensors9THERMO_2 +k‐Type Thermocouple10IN21Thermistor Input11IN185V Analogue Input12IN14Configurable Analogue Input13IN11Configurable Analogue Input14IN07Configurable Analogue Input15IN04Configurable Analogue Input16IN01Configurable Analogue Input17LAM 1 ILambda sensors18CAN 2 LOCAN bus19RS232 TXRS23220LAN RX‐COM CABLE21FUEL07Fuel Injector (10A Open Collector)22FUEL03Fuel Injector (10A Open Collector)23VBATVoltage Supply24PWRGNDEcu Ground25IN265V Analogue Input265V OUT5V OUT27KNOCK 1Knock Sensors28THERMO_1 ‐k‐Type Thermocouple29IN22Thermistor Input30IN195V Analogue Input31IN15Configurable Analogue Input32IN12Configurable Analogue Input33IN08Configurable Analogue Input34ANGNDSENSOR GROUND35IN02Configurable Analogue Input36LAM 1 VLambda sensors37CAN 3 HICAN bus38RS232 RXRS23239LAN RX+COM CABLE40FUEL08Fuel Injector (10A Open Collector)41FUEL04Fuel Injector (10A Open Collector)42VBATVoltage Supply43PWRGNDEcu Ground44IN275V Analogue Input455V OUT5V OUT46KNOCK 2Knock Sensors47THERMO_1 +k‐Type Thermocouple48IN23Thermistor Input49IN205V Analogue Input50IN16Configurable Analogue Input51ANGNDSENSOR GROUND52IN09Configurable Analogue Input53IN05Configurable Analogue Input54ANGNDSENSOR GROUND55LAM 2 VLambda sensors56CAN 3 LOCAN bus57RS232 GNDRS23258CAN 1 HICAN bus59LAN TX‐COM CABLE60FUEL05Fuel Injector (10A Open Collector)61FUEL01Fuel Injector (10A Open Collector)62HBRIDGE 5H‐Bridge63IN285V Analogue Input6410VOUT65KNOCK 3Knock Sensors66THERMO_2 ‐k‐Type Thermocouple67IN24Thermistor Input68ANGNDSENSOR GROUND69IN175V Analogue Input70IN13Configurable Analogue Input71IN10Configurable Analogue Input72IN06Configurable Analogue Input73IN03Configurable Analogue Input74LAM 2 ILambda sensors75LAM GNDLambda Sensors76CAN 2 HICAN bus77CAN 1 LOCAN bus78LAN TX+COM CABLE79FUEL06Fuel Injector (10A Open Collector)80FUEL02Fuel Injector (10A Open Collector)81HBRIDGE 6H‐Bridge82HBRIDGE 1H‐Bridge83PWM4PWM84PWM8PWM85FUEL12Fuel Injector (10A Open Collector)86FUEL16Fuel Injector (10A Open Collector)87FUEL20Fuel Injector (10A Open Collector)88FUEL24Fuel Injector (10A Open Collector)89VBATVoltage Supply90HBRIDGE 2H‐Bridge91PWM3PWM92PWM7PWM93FUEL11Fuel Injector (10A Open Collector)94FUEL15Fuel Injector (10A Open Collector)95FUEL19Fuel Injector (10A Open Collector)96FUEL23Fuel Injector (10A Open Collector)97PWRGNDEcu Ground98HBRIDGE 3H‐Bridge99PWM2PWM100PWM6PWM101FUEL10Fuel Injector (10A Open Collector)102FUEL14Fuel Injector (10A Open Collector)103FUEL18Fuel Injector (10A Open Collector)104FUEL22Fuel Injector (10A Open Collector)105PWRGNDEcu Ground106HBRIDGE 4H‐Bridge107PWM1PWM108PWM5PWM109FUEL09Fuel Injector (10A Open Collector)110FUEL13Fuel Injector (10A Open Collector)111FUEL17Fuel Injector (10A Open Collector)112FUEL21Fuel Injector (10A Open Collector)113PWRGNDEcu Ground114IGN05Ignition (20A Open Collector)115IGN06Ignition (20A Open Collector)116IGN07Ignition (20A Open Collector)117IGN08Ignition (20A Open Collector)118IGN09Ignition (20A Open Collector)119IGN10Ignition (20A Open Collector)120IGN11Ignition (20A Open Collector)121IGN12Ignition (20A Open Collector)

Calibration and sources

Syvecs uses SCal calibration software and provides firmware and base calibrations. Check version compatibility with the unit and preserve the existing tune before changes.

Syvecs product or ECU comparisonSyvecs ECU comparison and specification notesSyvecs product historyManufacturer wiring reference

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 2: Syvecs S12
Syvecs S12 ECU
Syvecs manufacturer product photograph, reproduced with permission. Image source.

Overview and hardware

Syvecs S12 is a British engine-management ECU. Flagship V12/high-I/O ECU launched in 2014. Manufacturer lists 28 inputs, 24 port injector outputs, 12 ignition outputs, 3 full bridges, 8 extra PWM outputs, 4 knock, 2 EGT, 3 CAN, 121 pins and 6–26 V. Its detailed specification lists two NTK lambda interfaces, but a short summary says four; confirm with Syvecs. Direct injection requires compatible external hardware and software.

Compare the required injector, ignition, actuator and sensor channels with the hardware available on the actual ECU. Capabilities and configurable functions depend on firmware, hardware revision and calibration.

Wiring and pinout

Manufacturer S12 wiring guide and pinout. Use the guide's connector view and pin numbering and verify ECU hardware revision and configuration before wiring. Pin and input functions may vary by calibration or vehicle. Syvecs wiring index contains further example pinout files.

Vehicle-specific replacement kits use their own harness or carrier board. Consult the corresponding vehicle-specific Syvecs guide rather than assuming a generic schedule applies.

Calibration and sources

Syvecs uses SCal calibration software and provides firmware and base calibrations. Check version compatibility with the unit and preserve the existing tune before changes.

Revision 3: Syvecs S12
Syvecs S12 ECU
Syvecs manufacturer product photograph, reproduced with permission. Image source.

Overview and hardware

Syvecs S12 is a British engine-management ECU. Flagship V12/high-I/O ECU launched in 2014. Manufacturer lists 28 inputs, 24 port injector outputs, 12 ignition outputs, 3 full bridges, 8 extra PWM outputs, 4 knock, 2 EGT, 3 CAN, 121 pins and 6–26 V. Its detailed specification lists two NTK lambda interfaces, but a short summary says four; confirm with Syvecs. Direct injection requires compatible external hardware and software.

Compare the required injector, ignition, actuator and sensor channels with the hardware available on the actual ECU. Capabilities and configurable functions depend on firmware, hardware revision and calibration.

Wiring and pinout

Manufacturer S12 wiring guide and pinout. Use the guide's connector view and pin numbering and verify ECU hardware revision and configuration before wiring. Pin and input functions may vary by calibration or vehicle. Syvecs wiring index contains further example pinout files.

Vehicle-specific replacement kits use their own harness or carrier board. Consult the corresponding vehicle-specific Syvecs guide rather than assuming a generic schedule applies.

Complete connector pin assignments

These 121 pin positions, source labels and functions are taken from the Syvecs S12 wiring guide. Confirm the connector view, device settings and wiring limits in the original before wiring; channels may be configurable.

PinSource labelFunction
1PWRGNDEcu Ground
2IGN01Ignition (20A Open Collector)
3IGN02Ignition (20A Open Collector)
4IGN03Ignition (20A Open Collector)
5IGN04Ignition (20A Open Collector)
6IN255V Analogue Input
7KNOCK 4Knock Sensors
8KNOCKGNDKnock Sensors
9THERMO_2 +k‐Type Thermocouple
10IN21Thermistor Input
11IN185V Analogue Input
12IN14Configurable Analogue Input
13IN11Configurable Analogue Input
14IN07Configurable Analogue Input
15IN04Configurable Analogue Input
16IN01Configurable Analogue Input
17LAM 1 ILambda sensors
18CAN 2 LOCAN bus
19RS232 TXRS232
20LAN RX‐COM CABLE
21FUEL07Fuel Injector (10A Open Collector)
22FUEL03Fuel Injector (10A Open Collector)
23VBATVoltage Supply
24PWRGNDEcu Ground
25IN265V Analogue Input
265V OUT5V OUT
27KNOCK 1Knock Sensors
28THERMO_1 ‐k‐Type Thermocouple
29IN22Thermistor Input
30IN195V Analogue Input
31IN15Configurable Analogue Input
32IN12Configurable Analogue Input
33IN08Configurable Analogue Input
34ANGNDSENSOR GROUND
35IN02Configurable Analogue Input
36LAM 1 VLambda sensors
37CAN 3 HICAN bus
38RS232 RXRS232
39LAN RX+COM CABLE
40FUEL08Fuel Injector (10A Open Collector)
41FUEL04Fuel Injector (10A Open Collector)
42VBATVoltage Supply
43PWRGNDEcu Ground
44IN275V Analogue Input
455V OUT5V OUT
46KNOCK 2Knock Sensors
47THERMO_1 +k‐Type Thermocouple
48IN23Thermistor Input
49IN205V Analogue Input
50IN16Configurable Analogue Input
51ANGNDSENSOR GROUND
52IN09Configurable Analogue Input
53IN05Configurable Analogue Input
54ANGNDSENSOR GROUND
55LAM 2 VLambda sensors
56CAN 3 LOCAN bus
57RS232 GNDRS232
58CAN 1 HICAN bus
59LAN TX‐COM CABLE
60FUEL05Fuel Injector (10A Open Collector)
61FUEL01Fuel Injector (10A Open Collector)
62HBRIDGE 5H‐Bridge
63IN285V Analogue Input
6410VOUT
65KNOCK 3Knock Sensors
66THERMO_2 ‐k‐Type Thermocouple
67IN24Thermistor Input
68ANGNDSENSOR GROUND
69IN175V Analogue Input
70IN13Configurable Analogue Input
71IN10Configurable Analogue Input
72IN06Configurable Analogue Input
73IN03Configurable Analogue Input
74LAM 2 ILambda sensors
75LAM GNDLambda Sensors
76CAN 2 HICAN bus
77CAN 1 LOCAN bus
78LAN TX+COM CABLE
79FUEL06Fuel Injector (10A Open Collector)
80FUEL02Fuel Injector (10A Open Collector)
81HBRIDGE 6H‐Bridge
82HBRIDGE 1H‐Bridge
83PWM4PWM
84PWM8PWM
85FUEL12Fuel Injector (10A Open Collector)
86FUEL16Fuel Injector (10A Open Collector)
87FUEL20Fuel Injector (10A Open Collector)
88FUEL24Fuel Injector (10A Open Collector)
89VBATVoltage Supply
90HBRIDGE 2H‐Bridge
91PWM3PWM
92PWM7PWM
93FUEL11Fuel Injector (10A Open Collector)
94FUEL15Fuel Injector (10A Open Collector)
95FUEL19Fuel Injector (10A Open Collector)
96FUEL23Fuel Injector (10A Open Collector)
97PWRGNDEcu Ground
98HBRIDGE 3H‐Bridge
99PWM2PWM
100PWM6PWM
101FUEL10Fuel Injector (10A Open Collector)
102FUEL14Fuel Injector (10A Open Collector)
103FUEL18Fuel Injector (10A Open Collector)
104FUEL22Fuel Injector (10A Open Collector)
105PWRGNDEcu Ground
106HBRIDGE 4H‐Bridge
107PWM1PWM
108PWM5PWM
109FUEL09Fuel Injector (10A Open Collector)
110FUEL13Fuel Injector (10A Open Collector)
111FUEL17Fuel Injector (10A Open Collector)
112FUEL21Fuel Injector (10A Open Collector)
113PWRGNDEcu Ground
114IGN05Ignition (20A Open Collector)
115IGN06Ignition (20A Open Collector)
116IGN07Ignition (20A Open Collector)
117IGN08Ignition (20A Open Collector)
118IGN09Ignition (20A Open Collector)
119IGN10Ignition (20A Open Collector)
120IGN11Ignition (20A Open Collector)
121IGN12Ignition (20A Open Collector)

Calibration and sources

Syvecs uses SCal calibration software and provides firmware and base calibrations. Check version compatibility with the unit and preserve the existing tune before changes.