Page organisation in this revision
- Page type
- Reference hub
- Subject
- Engine ECU
- Parent
- Syvecs Standalone ECUs
- Applies to
- No ECU-specific applicability
- Tool groups
- None
- Manufacturers
- None
Changes from revision 1 to revision 2
Removed text is struck through; added text is highlighted.
Overview and hardware
Syvecs S6Plus is a British engine-management ECU. Syvecs introduced S6Plus in 2015 as an S6 upgrade with a dedicated third processor for additional vehicle integration. The manufacturer guide describes internal solder-bridge hardware configuration; verify its carrier board and hardware before replacing or configuring a unit.
Compare the required injector, ignition, actuator and sensor channels with the hardware available on the actual ECU. Capabilities and configurable functions depend on firmware, hardware revision and calibration.
Wiring and pinout
Manufacturer S6Plus wiring guide and pinout. Use the guide's connector view and pin numbering and verify ECU hardware revision and configuration before wiring. Pin and input functions may vary by calibration or vehicle. Syvecs wiring index contains further example pinout files.
Vehicle-specific replacement kits use their own harness or carrier board. Consult the corresponding vehicle-specific Syvecs guide rather than assuming a generic schedule applies.
Complete connector pin assignmentsThe following positions are from the Syvecs S6PLUS wiring guide. N/A reproduces the guide's unavailable label. Function examples can be reassigned; identify the connector view, build options and current limits in the original before wiring.Connector APinSource labelA1PWR CTR OUTA2H‐Bridge1 / SlaveOut1A3H‐Bridge2/ SlaveOut2A4H‐Bridge3 / SlaveOut3A5H‐Bridge4 / SlaveOut4A6H‐Bridge5 / SlaveOut5A7H‐Bridge6 / SlaveOut6A8H‐Bridge7 / SlaveOut7A9H‐Bridge8 / SlaveOut8A10FUEL1A11FUEL2A12FUEL3A13FUEL4A14FUEL5A15FUEL6A16FUEL7A17FUEL8A18FUEL9/PWM1A19FUEL10/PWM2A20FUEL11/PWM3A21FUEL12/PWM4A22FUEL13/PWM5A23FUEL14/PWM6A24FUEL15/PWM7A25FUEL16/PWM8A26IGN1A27IGN2A28IGN3A29IGN4A30IGN5A31IGN6A32PWRGNDA33PWRGNDA34PWRGNDConnector BPinSource labelB1PWRGNDB2EGT2 +B3EGT2 ‐B4KNOCKB5KNOCK 2B6PVBATB7VBATB8LAM1AB9LAM1BB10LAM1CB11LAM1DB12LAM1HEATERB13VBATB14LAM2AB15LAM2BB16LAM2CB17LAM2DB18LAM2HEATERB19VBATB20KLINEB21RS232RXB22RS232TXB23LANRX‐B24LANRX+B25LANTX‐B26LANTX+Connector CPinSource labelC1KNOCK GROUNDSC2ANGNDC3ANGNDC4ANGNDC55V OUTC65V OUTC75V OUTC8CAN LC9CAN HC10AN01C11AN02C12AN03C13AN04C14AN05C15AN06C16AN07C17AN08C18AN09C19AN10C20AN11C21AN12C22AN13C23AN14C24AN15C25AN16C26EGT1‐C27EGT1+C28PWR CTR INC29AN S1 / Slave An01C30AN S2 / Slave An02C31AN S3 / Slave An03C32AN S4 / Slave An04C33AN S5 / Slave An05C34AN S6 / Slave An06Calibration and sources
Syvecs uses SCal calibration software and provides firmware and base calibrations. Check version compatibility with the unit and preserve the existing tune before changes.
Syvecs product or ECU comparisonSyvecs ECU comparison and specification notesSyvecs product historyManufacturer wiring reference
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 1: Syvecs S6Plus
Overview and hardware
Syvecs S6Plus is a British engine-management ECU. Syvecs introduced S6Plus in 2015 as an S6 upgrade with a dedicated third processor for additional vehicle integration. The manufacturer guide describes internal solder-bridge hardware configuration; verify its carrier board and hardware before replacing or configuring a unit.
Compare the required injector, ignition, actuator and sensor channels with the hardware available on the actual ECU. Capabilities and configurable functions depend on firmware, hardware revision and calibration.
Wiring and pinout
Manufacturer S6Plus wiring guide and pinout. Use the guide's connector view and pin numbering and verify ECU hardware revision and configuration before wiring. Pin and input functions may vary by calibration or vehicle. Syvecs wiring index contains further example pinout files.
Vehicle-specific replacement kits use their own harness or carrier board. Consult the corresponding vehicle-specific Syvecs guide rather than assuming a generic schedule applies.
Calibration and sources
Syvecs uses SCal calibration software and provides firmware and base calibrations. Check version compatibility with the unit and preserve the existing tune before changes.
Revision 2: Syvecs S6Plus
Overview and hardware
Syvecs S6Plus is a British engine-management ECU. Syvecs introduced S6Plus in 2015 as an S6 upgrade with a dedicated third processor for additional vehicle integration. The manufacturer guide describes internal solder-bridge hardware configuration; verify its carrier board and hardware before replacing or configuring a unit.
Compare the required injector, ignition, actuator and sensor channels with the hardware available on the actual ECU. Capabilities and configurable functions depend on firmware, hardware revision and calibration.
Wiring and pinout
Manufacturer S6Plus wiring guide and pinout. Use the guide's connector view and pin numbering and verify ECU hardware revision and configuration before wiring. Pin and input functions may vary by calibration or vehicle. Syvecs wiring index contains further example pinout files.
Vehicle-specific replacement kits use their own harness or carrier board. Consult the corresponding vehicle-specific Syvecs guide rather than assuming a generic schedule applies.
Complete connector pin assignments
The following positions are from the Syvecs S6PLUS wiring guide. N/A reproduces the guide's unavailable label. Function examples can be reassigned; identify the connector view, build options and current limits in the original before wiring.
Connector A
| Pin | Source label |
|---|
| A1 | PWR CTR OUT |
| A2 | H‐Bridge1 / SlaveOut1 |
| A3 | H‐Bridge2/ SlaveOut2 |
| A4 | H‐Bridge3 / SlaveOut3 |
| A5 | H‐Bridge4 / SlaveOut4 |
| A6 | H‐Bridge5 / SlaveOut5 |
| A7 | H‐Bridge6 / SlaveOut6 |
| A8 | H‐Bridge7 / SlaveOut7 |
| A9 | H‐Bridge8 / SlaveOut8 |
| A10 | FUEL1 |
| A11 | FUEL2 |
| A12 | FUEL3 |
| A13 | FUEL4 |
| A14 | FUEL5 |
| A15 | FUEL6 |
| A16 | FUEL7 |
| A17 | FUEL8 |
| A18 | FUEL9/PWM1 |
| A19 | FUEL10/PWM2 |
| A20 | FUEL11/PWM3 |
| A21 | FUEL12/PWM4 |
| A22 | FUEL13/PWM5 |
| A23 | FUEL14/PWM6 |
| A24 | FUEL15/PWM7 |
| A25 | FUEL16/PWM8 |
| A26 | IGN1 |
| A27 | IGN2 |
| A28 | IGN3 |
| A29 | IGN4 |
| A30 | IGN5 |
| A31 | IGN6 |
| A32 | PWRGND |
| A33 | PWRGND |
| A34 | PWRGND |
Connector B
| Pin | Source label |
|---|
| B1 | PWRGND |
| B2 | EGT2 + |
| B3 | EGT2 ‐ |
| B4 | KNOCK |
| B5 | KNOCK 2 |
| B6 | PVBAT |
| B7 | VBAT |
| B8 | LAM1A |
| B9 | LAM1B |
| B10 | LAM1C |
| B11 | LAM1D |
| B12 | LAM1HEATER |
| B13 | VBAT |
| B14 | LAM2A |
| B15 | LAM2B |
| B16 | LAM2C |
| B17 | LAM2D |
| B18 | LAM2HEATER |
| B19 | VBAT |
| B20 | KLINE |
| B21 | RS232RX |
| B22 | RS232TX |
| B23 | LANRX‐ |
| B24 | LANRX+ |
| B25 | LANTX‐ |
| B26 | LANTX+ |
Connector C
| Pin | Source label |
|---|
| C1 | KNOCK GROUNDS |
| C2 | ANGND |
| C3 | ANGND |
| C4 | ANGND |
| C5 | 5V OUT |
| C6 | 5V OUT |
| C7 | 5V OUT |
| C8 | CAN L |
| C9 | CAN H |
| C10 | AN01 |
| C11 | AN02 |
| C12 | AN03 |
| C13 | AN04 |
| C14 | AN05 |
| C15 | AN06 |
| C16 | AN07 |
| C17 | AN08 |
| C18 | AN09 |
| C19 | AN10 |
| C20 | AN11 |
| C21 | AN12 |
| C22 | AN13 |
| C23 | AN14 |
| C24 | AN15 |
| C25 | AN16 |
| C26 | EGT1‐ |
| C27 | EGT1+ |
| C28 | PWR CTR IN |
| C29 | AN S1 / Slave An01 |
| C30 | AN S2 / Slave An02 |
| C31 | AN S3 / Slave An03 |
| C32 | AN S4 / Slave An04 |
| C33 | AN S5 / Slave An05 |
| C34 | AN S6 / Slave An06 |
Calibration and sources
Syvecs uses SCal calibration software and provides firmware and base calibrations. Check version compatibility with the unit and preserve the existing tune before changes.