Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
Syvecs Standalone ECUs
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Changes from revision 1 to revision 2

Removed text is struck through; added text is highlighted.

Syvecs manufacturer product photograph, reproduced with permission. Image source.

Overview and hardware

Syvecs S7D-6 is a British engine-management ECU. Six integrated DI channels and two DI pump outputs; 8 low-side port-injector outputs, 6 ignition and 6 extra low-side PWM. The 22 general-purpose inputs comprise 14 frequency, 4 ADC and 4 thermistor inputs; 2 wideband, 2 knock, 2 EGT, 3 CAN including CAN FD, 120 pins, 6–20 V. The comparison specifies six integrated channels despite the family product summary saying up to eight: confirm actual hardware.

Compare the required injector, ignition, actuator and sensor channels with the hardware available on the actual ECU. Capabilities and configurable functions depend on firmware, hardware revision and calibration.

Wiring and pinout

Manufacturer S7D-6 wiring guide and pinout. Use the guide's connector view and pin numbering and verify ECU hardware revision and configuration before wiring. Pin and input functions may vary by calibration or vehicle. Syvecs wiring index contains further example pinout files.

Vehicle-specific replacement kits use their own harness or carrier board. Consult the corresponding vehicle-specific Syvecs guide rather than assuming a generic schedule applies.

Complete connector pin assignmentsAll 94 positions below follow the Syvecs S7D-6 model-specific wiring guide, using the guide's source labels. N/A reproduces a source-marked unavailable position. Pin names describe hardware channels; assignments, software configuration, connector orientation, hardware options and electrical limits must be checked in that guide for the exact ECU.The manufacturer describes ignition outputs as TTL by default with IGBT available as an option. The guide labels C4 as a sensor ground while its notes also say linked power ground; confirm grounding for the actual build. Direct-injector high- and low-side pairings must follow the specific diagram and electrical limits.Connector APinSource labelA1PWR CTR OUTA2H‐Bridge1A3H‐Bridge2A4H‐Bridge3A5H‐Bridge4A6H‐Bridge5A7H‐Bridge6A8H‐Bridge7A9H‐Bridge8A10GDI LS1A11GDI LS2A12GDI LS3A13GDI LS4A14Fuel 5A15GDI LS6A16Fuel 7A17GDI LS8A18GDI HS1/2A19GDI HS3/4A20GDI Pump 1 HSA21GDI HS5/6A22GDI HS7/8A23GDI Pump 2 HSA24GDI Pump 1 LSA25GDI Pump 2 LSA26IGN1A27IGN2A28IGN3A29IGN4A30IGN5A31IGN6A32PWRGNDA33PWRGNDA34PWRGNDConnector BPinSource labelB1PWRGNDB2CAN2 LB3CAN2 HB4KNOCK 1B5KNOCK 2B6PVBATB7IVBATB8LAM1AB9LAM1BB10LAM1CB11LAM1DB12LAM1HEATERB13IVBATB14LAM2AB15LAM2BB16LAM2CB17LAM2DB18LAM2HEATERB19IVBATB20KLINEB21RS232RXB22RS232TXB23LAN RX− (Cat5 pin 2)B24LAN RX+ (Cat5 pin 1)B25LAN TX− (Cat5 pin 6)B26LAN TX+ (Cat5 pin 3)Connector CPinSource labelC1KNOCKGNDC2ANGNDC3ANGNDC4ANGNDC55V OUTC65V OUTC75V OUTC8CAN1 LC9CAN1 HC10AN01C11AN02C12AN03C13AN04C14AN05C15AN06C16AN07C17AN08C18AN09C19AN10C20AN11C21AN12C22AN13C23AN14C24AN15C25AN16C26EGT1‐C27EGT1+C28PWR CTR INC29AN S1C30AN S2C31AN S3C32AN S4C33AN S5C34AN S6

Calibration and sources

Syvecs uses SCal calibration software and provides firmware and base calibrations. Check version compatibility with the unit and preserve the existing tune before changes.

Syvecs product or ECU comparisonSyvecs ECU comparison and specification notesSyvecs product historyManufacturer wiring reference

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 1: Syvecs S7D-6
Syvecs S7D-6 ECU
Syvecs manufacturer product photograph, reproduced with permission. Image source.

Overview and hardware

Syvecs S7D-6 is a British engine-management ECU. Six integrated DI channels and two DI pump outputs; 8 low-side port-injector outputs, 6 ignition and 6 extra low-side PWM. The 22 general-purpose inputs comprise 14 frequency, 4 ADC and 4 thermistor inputs; 2 wideband, 2 knock, 2 EGT, 3 CAN including CAN FD, 120 pins, 6–20 V. The comparison specifies six integrated channels despite the family product summary saying up to eight: confirm actual hardware.

Compare the required injector, ignition, actuator and sensor channels with the hardware available on the actual ECU. Capabilities and configurable functions depend on firmware, hardware revision and calibration.

Wiring and pinout

Manufacturer S7D-6 wiring guide and pinout. Use the guide's connector view and pin numbering and verify ECU hardware revision and configuration before wiring. Pin and input functions may vary by calibration or vehicle. Syvecs wiring index contains further example pinout files.

Vehicle-specific replacement kits use their own harness or carrier board. Consult the corresponding vehicle-specific Syvecs guide rather than assuming a generic schedule applies.

Calibration and sources

Syvecs uses SCal calibration software and provides firmware and base calibrations. Check version compatibility with the unit and preserve the existing tune before changes.

Revision 2: Syvecs S7D-6
Syvecs S7D-6 ECU
Syvecs manufacturer product photograph, reproduced with permission. Image source.

Overview and hardware

Syvecs S7D-6 is a British engine-management ECU. Six integrated DI channels and two DI pump outputs; 8 low-side port-injector outputs, 6 ignition and 6 extra low-side PWM. The 22 general-purpose inputs comprise 14 frequency, 4 ADC and 4 thermistor inputs; 2 wideband, 2 knock, 2 EGT, 3 CAN including CAN FD, 120 pins, 6–20 V. The comparison specifies six integrated channels despite the family product summary saying up to eight: confirm actual hardware.

Compare the required injector, ignition, actuator and sensor channels with the hardware available on the actual ECU. Capabilities and configurable functions depend on firmware, hardware revision and calibration.

Wiring and pinout

Manufacturer S7D-6 wiring guide and pinout. Use the guide's connector view and pin numbering and verify ECU hardware revision and configuration before wiring. Pin and input functions may vary by calibration or vehicle. Syvecs wiring index contains further example pinout files.

Vehicle-specific replacement kits use their own harness or carrier board. Consult the corresponding vehicle-specific Syvecs guide rather than assuming a generic schedule applies.

Complete connector pin assignments

All 94 positions below follow the Syvecs S7D-6 model-specific wiring guide, using the guide's source labels. N/A reproduces a source-marked unavailable position. Pin names describe hardware channels; assignments, software configuration, connector orientation, hardware options and electrical limits must be checked in that guide for the exact ECU.

The manufacturer describes ignition outputs as TTL by default with IGBT available as an option. The guide labels C4 as a sensor ground while its notes also say linked power ground; confirm grounding for the actual build. Direct-injector high- and low-side pairings must follow the specific diagram and electrical limits.

Connector A

PinSource label
A1PWR CTR OUT
A2H‐Bridge1
A3H‐Bridge2
A4H‐Bridge3
A5H‐Bridge4
A6H‐Bridge5
A7H‐Bridge6
A8H‐Bridge7
A9H‐Bridge8
A10GDI LS1
A11GDI LS2
A12GDI LS3
A13GDI LS4
A14Fuel 5
A15GDI LS6
A16Fuel 7
A17GDI LS8
A18GDI HS1/2
A19GDI HS3/4
A20GDI Pump 1 HS
A21GDI HS5/6
A22GDI HS7/8
A23GDI Pump 2 HS
A24GDI Pump 1 LS
A25GDI Pump 2 LS
A26IGN1
A27IGN2
A28IGN3
A29IGN4
A30IGN5
A31IGN6
A32PWRGND
A33PWRGND
A34PWRGND

Connector B

PinSource label
B1PWRGND
B2CAN2 L
B3CAN2 H
B4KNOCK 1
B5KNOCK 2
B6PVBAT
B7IVBAT
B8LAM1A
B9LAM1B
B10LAM1C
B11LAM1D
B12LAM1HEATER
B13IVBAT
B14LAM2A
B15LAM2B
B16LAM2C
B17LAM2D
B18LAM2HEATER
B19IVBAT
B20KLINE
B21RS232RX
B22RS232TX
B23LAN RX− (Cat5 pin 2)
B24LAN RX+ (Cat5 pin 1)
B25LAN TX− (Cat5 pin 6)
B26LAN TX+ (Cat5 pin 3)

Connector C

PinSource label
C1KNOCKGND
C2ANGND
C3ANGND
C4ANGND
C55V OUT
C65V OUT
C75V OUT
C8CAN1 L
C9CAN1 H
C10AN01
C11AN02
C12AN03
C13AN04
C14AN05
C15AN06
C16AN07
C17AN08
C18AN09
C19AN10
C20AN11
C21AN12
C22AN13
C23AN14
C24AN15
C25AN16
C26EGT1‐
C27EGT1+
C28PWR CTR IN
C29AN S1
C30AN S2
C31AN S3
C32AN S4
C33AN S5
C34AN S6

Calibration and sources

Syvecs uses SCal calibration software and provides firmware and base calibrations. Check version compatibility with the unit and preserve the existing tune before changes.