Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
Syvecs Standalone ECUs
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Changes from revision 1 to revision 3

Removed text is struck through; added text is highlighted.

Syvecs manufacturer product photograph, reproduced with permission. Image source.

Overview and hardware

Syvecs S8 is a British engine-management ECU. Launched in 2011 according to Syvecs; 24 inputs, 16 low-side injector outputs, 8 ignition outputs and 4 half bridges; 2 lambda, 2 knock and 2 EGT, 2 CAN, 88 pins, 6–20 V. Direct injection requires a compatible external GDI12 driver, software and suitable calibration.

Compare the required injector, ignition, actuator and sensor channels with the hardware available on the actual ECU. Capabilities and configurable functions depend on firmware, hardware revision and calibration.

Wiring and pinout

Manufacturer S8 wiring guide and pinout. Use the guide's connector view and pin numbering and verify ECU hardware revision and configuration before wiring. Pin and input functions may vary by calibration or vehicle. Syvecs wiring index contains further example pinout files.

Vehicle-specific replacement kits use their own harness or carrier board. Consult the corresponding vehicle-specific Syvecs guide rather than assuming a generic schedule applies.

Complete connector pin assignmentsThese 88 pin positions, source labels and functions are taken from the Syvecs S8 wiring guide. Confirm the connector view, device settings and wiring limits in the original before wiring; channels may be configurable.The source uses ANGND1 and ANGND2 labels inconsistently with its numbered descriptions at pins 67 and 69. The table preserves the printed labels; confirm the correct ground arrangement for the actual installation.PinSource labelFunction1PWRGNDPOWER GROUND2IGN8IGNITION (20A OPEN COLLECTOR)3IGN7IGNITION (20A OPEN COLLECTOR)4IGN6IGNITION (20A OPEN COLLECTOR)5IGN5IGNITION (20A OPEN COLLECTOR)6FUEL10FUEL INJECTOR (10A OPEN COLLECTOR)7KNK2KNOCK SENSOR 28AN16CONFIGURABLE ANALOGUE INPUT9AN14CONFIGURABLE ANALOGUE INPUT10AN12CONFIGURABLE ANALOGUE INPUT11AN10CONFIGURABLE ANALOGUE INPUT12EGT2‐K TYPE THERMOCOUPLE NEGATIVE INPUT13EGT2+K TYPE THERMOCOUPLE POSITIVE INPUT14AN7CONFIGURABLE ANALOGUE INPUT15AN5CONFIGURABLE ANALOGUE INPUT16AN3CONFIGURABLE ANALOGUE INPUT17AN1CONFIGURABLE ANALOGUE INPUT18LAM1VNTK UEGO SENSOR 1 NERNST VOLTAGE19AN21THERMISTOR INPUT20FUEL15FUEL INJECTOR (10A OPEN COLLECTOR)21RS232#1TXRS232 TRANSMIT22FUEL7FUEL INJECTOR (10A OPEN COLLECTOR)23FUEL5FUEL INJECTOR (10A OPEN COLLECTOR)24IGN4IGNITION (20A OPEN COLLECTOR)25IGN3IGNITION (20A OPEN COLLECTOR)26IGN2IGNITION (20A OPEN COLLECTOR)27IGN1IGNITION (20A OPEN COLLECTOR)28PWRGNDECU GROUNG29PWRGNDECU GROUND30FUEL14FUEL INJECTOR (10A OPEN COLLECTOR)31FUEL13FUEL INJECTOR (10A OPEN COLLECTOR)32FUEL12FUEL INJECTOR (10A OPEN COLLECTOR)33FUEL11FUEL INJECTOR (10A OPEN COLLECTOR)34FUEL9FUEL INJECTOR (10A OPEN COLLECTOR)35KNKKNOCK SENSOR SIGNAL36AN15CONFIGURABLE ANALOGUE INPUT37AN13CONFIGURABLE ANALOGUE INPUT38AN11CONFIGURABLE ANALOGUE INPUT39AN9CONFIGURABLE ANALOGUE INPUT40EGT1‐K TYPE THERMOCOUPLE NEGATIVE INPUT41AN8CONFIGURABLE ANALOGUE INPUT42AN6CONFIGURABLE ANALOGUE INPUT43AN4CONFIGURABLE ANALOGUE INPUT44AN2CONFIGURABLE ANALOGUE INPUT45LAM#2VNTK UEGO SENSOR 2 NERNST VOLTAGE46AN22THERMISTOR INPUT47FUEL16FUEL INJECTOR (10A OPEN COLLECTOR)48RS232#1RXRS232 RECEIVE49FUEL8FUEL INJECTOR (10A OPEN COLLECTOR)50FUEL6FUEL INJECTOR (10A OPEN COLLECTOR)51FUEL4FUEL INJECTOR (10A OPEN COLLECTOR)52FUEL3FUEL INJECTOR (10A OPEN COLLECTOR)53FUEL2FUEL INJECTOR (10A OPEN COLLECTOR)54FUEL1FUEL INJECTOR (10A OPEN COLLECTOR)55PWRGNDECU GND56VBATECU +12V SUPPLY57VBATECU +12V SUPPLY58H BRIDGE1H BRIDGE159H BRIDGE2H BRIDGE260H BRIDGE3H BRIDGE361H BRIDGE4H BRIDGE46210VOUTLOW CURRENT PROGRAMMABLE OUTPUT635VOUT2+5V SENSOR SUPPLY OUTPUT645VOUT1+5V SENSOR SUPPLY OUTPUT65KNKGNDKNOCK SENSOR GROUND66AN205V ANALOGUE INPUT67ANGND2SENSOR GROUND #168AN195V ANALOGUE INPUT69ANGND1SENSOR GROUND #270EGT1+K TYPE THERMOCOUPLE POSITIVE INPUT71AN185V ANALOGUE INPUT72ANGND2SENSOR GROUND #273AN175V ANALOGUE INPUT74ANGND1SENSOR GROUND #175LAM2INTK UEGO SENSOR 2 ION PUMP76LAMINTK UEGO SENSOR 1 ION PUMP77LAMGNDLAMBDA SENSOR SIGNAL GROUND78COMGNDRS232 COMMS GROUND79CAN2LOCONTROLLER AREA NETWORK #2 SIGNAL LOW80CAN2HICONTROLLER AREA NETWORK #2 SIGNAL HIGH81CAN1LOCONTROLLER AREA NETWORK #1 SIGNAL LOW82CAN1HICONTROLLER AREA NETWORK #1 SIGNAL HIGH83AN24THERMISTOR INPUT84AN23THERMISTOR INPUT85LANRX+100 BASET ETHERNET RECEIVE86LANRX‐100 BASET ETHERNET RECEIVE87LANTX+100 BASET ETHERNET TRANSMIT88LANTX‐100 BASET ETHERNET TRANSMIT

Calibration and sources

Syvecs uses SCal calibration software and provides firmware and base calibrations. Check version compatibility with the unit and preserve the existing tune before changes.

Syvecs product or ECU comparisonSyvecs ECU comparison and specification notesSyvecs product historyManufacturer wiring reference

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 1: Syvecs S8

Overview and hardware

Syvecs S8 is a British engine-management ECU. Launched in 2011 according to Syvecs; 24 inputs, 16 low-side injector outputs, 8 ignition outputs and 4 half bridges; 2 lambda, 2 knock and 2 EGT, 2 CAN, 88 pins, 6–20 V. Direct injection requires a compatible external GDI12 driver, software and suitable calibration.

Compare the required injector, ignition, actuator and sensor channels with the hardware available on the actual ECU. Capabilities and configurable functions depend on firmware, hardware revision and calibration.

Wiring and pinout

Manufacturer S8 wiring guide and pinout. Use the guide's connector view and pin numbering and verify ECU hardware revision and configuration before wiring. Pin and input functions may vary by calibration or vehicle. Syvecs wiring index contains further example pinout files.

Vehicle-specific replacement kits use their own harness or carrier board. Consult the corresponding vehicle-specific Syvecs guide rather than assuming a generic schedule applies.

Calibration and sources

Syvecs uses SCal calibration software and provides firmware and base calibrations. Check version compatibility with the unit and preserve the existing tune before changes.

Revision 3: Syvecs S8
Syvecs S8 ECU
Syvecs manufacturer product photograph, reproduced with permission. Image source.

Overview and hardware

Syvecs S8 is a British engine-management ECU. Launched in 2011 according to Syvecs; 24 inputs, 16 low-side injector outputs, 8 ignition outputs and 4 half bridges; 2 lambda, 2 knock and 2 EGT, 2 CAN, 88 pins, 6–20 V. Direct injection requires a compatible external GDI12 driver, software and suitable calibration.

Compare the required injector, ignition, actuator and sensor channels with the hardware available on the actual ECU. Capabilities and configurable functions depend on firmware, hardware revision and calibration.

Wiring and pinout

Manufacturer S8 wiring guide and pinout. Use the guide's connector view and pin numbering and verify ECU hardware revision and configuration before wiring. Pin and input functions may vary by calibration or vehicle. Syvecs wiring index contains further example pinout files.

Vehicle-specific replacement kits use their own harness or carrier board. Consult the corresponding vehicle-specific Syvecs guide rather than assuming a generic schedule applies.

Complete connector pin assignments

These 88 pin positions, source labels and functions are taken from the Syvecs S8 wiring guide. Confirm the connector view, device settings and wiring limits in the original before wiring; channels may be configurable.

The source uses ANGND1 and ANGND2 labels inconsistently with its numbered descriptions at pins 67 and 69. The table preserves the printed labels; confirm the correct ground arrangement for the actual installation.

PinSource labelFunction
1PWRGNDPOWER GROUND
2IGN8IGNITION (20A OPEN COLLECTOR)
3IGN7IGNITION (20A OPEN COLLECTOR)
4IGN6IGNITION (20A OPEN COLLECTOR)
5IGN5IGNITION (20A OPEN COLLECTOR)
6FUEL10FUEL INJECTOR (10A OPEN COLLECTOR)
7KNK2KNOCK SENSOR 2
8AN16CONFIGURABLE ANALOGUE INPUT
9AN14CONFIGURABLE ANALOGUE INPUT
10AN12CONFIGURABLE ANALOGUE INPUT
11AN10CONFIGURABLE ANALOGUE INPUT
12EGT2‐K TYPE THERMOCOUPLE NEGATIVE INPUT
13EGT2+K TYPE THERMOCOUPLE POSITIVE INPUT
14AN7CONFIGURABLE ANALOGUE INPUT
15AN5CONFIGURABLE ANALOGUE INPUT
16AN3CONFIGURABLE ANALOGUE INPUT
17AN1CONFIGURABLE ANALOGUE INPUT
18LAM1VNTK UEGO SENSOR 1 NERNST VOLTAGE
19AN21THERMISTOR INPUT
20FUEL15FUEL INJECTOR (10A OPEN COLLECTOR)
21RS232#1TXRS232 TRANSMIT
22FUEL7FUEL INJECTOR (10A OPEN COLLECTOR)
23FUEL5FUEL INJECTOR (10A OPEN COLLECTOR)
24IGN4IGNITION (20A OPEN COLLECTOR)
25IGN3IGNITION (20A OPEN COLLECTOR)
26IGN2IGNITION (20A OPEN COLLECTOR)
27IGN1IGNITION (20A OPEN COLLECTOR)
28PWRGNDECU GROUNG
29PWRGNDECU GROUND
30FUEL14FUEL INJECTOR (10A OPEN COLLECTOR)
31FUEL13FUEL INJECTOR (10A OPEN COLLECTOR)
32FUEL12FUEL INJECTOR (10A OPEN COLLECTOR)
33FUEL11FUEL INJECTOR (10A OPEN COLLECTOR)
34FUEL9FUEL INJECTOR (10A OPEN COLLECTOR)
35KNKKNOCK SENSOR SIGNAL
36AN15CONFIGURABLE ANALOGUE INPUT
37AN13CONFIGURABLE ANALOGUE INPUT
38AN11CONFIGURABLE ANALOGUE INPUT
39AN9CONFIGURABLE ANALOGUE INPUT
40EGT1‐K TYPE THERMOCOUPLE NEGATIVE INPUT
41AN8CONFIGURABLE ANALOGUE INPUT
42AN6CONFIGURABLE ANALOGUE INPUT
43AN4CONFIGURABLE ANALOGUE INPUT
44AN2CONFIGURABLE ANALOGUE INPUT
45LAM#2VNTK UEGO SENSOR 2 NERNST VOLTAGE
46AN22THERMISTOR INPUT
47FUEL16FUEL INJECTOR (10A OPEN COLLECTOR)
48RS232#1RXRS232 RECEIVE
49FUEL8FUEL INJECTOR (10A OPEN COLLECTOR)
50FUEL6FUEL INJECTOR (10A OPEN COLLECTOR)
51FUEL4FUEL INJECTOR (10A OPEN COLLECTOR)
52FUEL3FUEL INJECTOR (10A OPEN COLLECTOR)
53FUEL2FUEL INJECTOR (10A OPEN COLLECTOR)
54FUEL1FUEL INJECTOR (10A OPEN COLLECTOR)
55PWRGNDECU GND
56VBATECU +12V SUPPLY
57VBATECU +12V SUPPLY
58H BRIDGE1H BRIDGE1
59H BRIDGE2H BRIDGE2
60H BRIDGE3H BRIDGE3
61H BRIDGE4H BRIDGE4
6210VOUTLOW CURRENT PROGRAMMABLE OUTPUT
635VOUT2+5V SENSOR SUPPLY OUTPUT
645VOUT1+5V SENSOR SUPPLY OUTPUT
65KNKGNDKNOCK SENSOR GROUND
66AN205V ANALOGUE INPUT
67ANGND2SENSOR GROUND #1
68AN195V ANALOGUE INPUT
69ANGND1SENSOR GROUND #2
70EGT1+K TYPE THERMOCOUPLE POSITIVE INPUT
71AN185V ANALOGUE INPUT
72ANGND2SENSOR GROUND #2
73AN175V ANALOGUE INPUT
74ANGND1SENSOR GROUND #1
75LAM2INTK UEGO SENSOR 2 ION PUMP
76LAMINTK UEGO SENSOR 1 ION PUMP
77LAMGNDLAMBDA SENSOR SIGNAL GROUND
78COMGNDRS232 COMMS GROUND
79CAN2LOCONTROLLER AREA NETWORK #2 SIGNAL LOW
80CAN2HICONTROLLER AREA NETWORK #2 SIGNAL HIGH
81CAN1LOCONTROLLER AREA NETWORK #1 SIGNAL LOW
82CAN1HICONTROLLER AREA NETWORK #1 SIGNAL HIGH
83AN24THERMISTOR INPUT
84AN23THERMISTOR INPUT
85LANRX+100 BASET ETHERNET RECEIVE
86LANRX‐100 BASET ETHERNET RECEIVE
87LANTX+100 BASET ETHERNET TRANSMIT
88LANTX‐100 BASET ETHERNET TRANSMIT

Calibration and sources

Syvecs uses SCal calibration software and provides firmware and base calibrations. Check version compatibility with the unit and preserve the existing tune before changes.