Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
Emtron standalone ECUs
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Changes from revision 2 to revision 2

Removed text is struck through; added text is highlighted.

Emtron KV16M product image, courtesy of Emtron; reproduced with permission.

Emtron KV16M is a programmable standalone ECU from Emtron Australia. Sixteen fuel and twelve sequential ignition channels are listed. The KV16M has a 136-way Deutsch Autosport connector system, distinct from the Superseal KV16. Emtron KV16M datasheet.

Identification and configuration

Record the ECU model, serial, board revision and loaded firmware. The Emtune calibration determines the use of configurable inputs and outputs; electrical limits, ignition driver type, injector impedance and wired supplies must be checked for the actual unit. Emtron engine-management manual.

Connector pinouts

These tables reproduce the positions in Emtron's KV16M pinout. The source diagrams are viewed looking into the ECU connector. NC is the manufacturer's unconnected designation. Verify connector keying, revision, power, grounds and all limits in the original before wiring; assignments differ between models and hardware revisions.

Connector A

PinChannel NamePinChannel Name1Injection Channel 129Lambda 2 Heater +2Injection Channel 230Lambda 2 Heater -3Injection Channel 331Digital Input Ground Out4Injection Channel 432Ignition Channel 15Injection Channel 533Ignition Channel 26Injection Channel 634Ignition Channel 37Injection Channel 735Ignition Channel 48Injection Channel 836Ignition Channel 59Injection Channel 937Ignition Channel 610Injection Channel 1038Ignition Channel 711Injection Channel 1139Ignition Channel 812Injection Channel 1240Ignition Channel 913Injection Channel 1341Ignition Channel 1014Injection Channel 1442Ignition Channel 1115Injection Channel 1543Ignition Channel 1216Injection Channel 1644Digital Input 317Lambda 1 Nernst Cell (Vs)45Digital Input 218Lambda 1 Cal Resistor (CalR)46Digital Input 119Lambda 1 Pump Cell (Ip)47Digital Input 920Lambda 1 Virtual Ground (VGnd)48Digital Input 821Lambda 1 Heater +49Digital Input 722Lambda 1 Heater -50Digital Input 623Digital Input 1351Digital Input 524Digital Input 1452Digital Input 425Lambda 2 Pump Cell (Ip)53Digital Input 1026Lambda 2 Virtual Ground (VGnd)54Digital Input 1127Lambda 2 Nernst Cell (Vs)55Digital Input 1228Lambda 2 Cal Resistor (CalR)

Connector B

PinChannel NameAECU 14V SupplyBECU 14V SupplyCECU 14V SupplyDECU GroundEECU GroundFAuxiliary Output 16GAuxiliary Output 15HAuxiliary Output 14JAuxiliary Output 12KAuxiliary Output 10LAuxiliary Output 8MAuxiliary Output 7NAuxiliary Output 5PAuxiliary Output 3RAuxiliary Output 1SAuxiliary Output 2TECU 14V SupplyUECU GroundVECU GroundWAuxiliary Output 13XAuxiliary Output 11YAuxiliary Output 9ZAuxiliary Output 6aAuxiliary Output 4bECU GroundcECU Ground

Connector C

PinChannel NamePinChannel Name1Analog Input Channel 129Analog Sensor 0V Reference2Analog Input Channel 230Analog Sensor 0V Reference3Analog Input Channel 331Analog Sensor 0V Reference4Analog Input Channel 432Knock 2 +5Analog Input Channel 533Analog Out6Analog Input Channel 634CAN 2L7Analog Input Channel 735CAN 2H8Analog Input Channel 836CAN 1L9Analog Input Channel 937CAN 1H10Analog Input Channel 1038Sensor Supply Vref2: 5.0V11Analog Input Channel 1139Sensor Supply Vref2: 5.0V12Analog Input Channel 1240Knock 1 -13Analog Input Channel 1341Sync Sensor -14Analog Input Channel 1442Sync Sensor +15Analog Input Channel 1543Crank Index Sensor -16Analog Input Channel 1644Crank Index Sensor +17Analog Input Channel 1745Sensor Supply Vref1: 5.0V18Analog Input Channel 1846Sensor Supply Vref1: 5.0V19Analog Input Channel 1947Knock 1 +20Analog Input Channel 2048Ethernet Tx +21Analog Input Channel 2149Ethernet Tx -22Analog Input Channel 2250Ethernet Rx +23Analog Input Channel 2351Ethernet Rx -24Analog Input Channel 2452Sensor Supply 8V25Knock 2 -53Constant 14V Supply(Backup)26SHIELD (Crank/Cam/ Knock)54Sensor Supply Vref3: 5.0V27SHIELD (Crank/Cam/ Knock)55Sensor Supply Vref3: 5.0V28Analog Sensor 0V Reference

Sensor 0 V references and main ECU grounds have distinct wiring requirements. H-bridge supplies and relay control require the installation described in the manufacturer's power-distribution guide. See Emtron wiring index and revision-specific diagrams.

Documentation and setup

Manufacturer's KV16M datasheet and product illustrationModel-specific pinout and connector diagramsEmtune setup and technical manualEmtron family reference

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 2: Emtron KV16M
Emtron KV16M ECU
Emtron KV16M product image, courtesy of Emtron; reproduced with permission.

Emtron KV16M is a programmable standalone ECU from Emtron Australia. Sixteen fuel and twelve sequential ignition channels are listed. The KV16M has a 136-way Deutsch Autosport connector system, distinct from the Superseal KV16. Emtron KV16M datasheet.

Identification and configuration

Record the ECU model, serial, board revision and loaded firmware. The Emtune calibration determines the use of configurable inputs and outputs; electrical limits, ignition driver type, injector impedance and wired supplies must be checked for the actual unit. Emtron engine-management manual.

Connector pinouts

These tables reproduce the positions in Emtron's KV16M pinout. The source diagrams are viewed looking into the ECU connector. NC is the manufacturer's unconnected designation. Verify connector keying, revision, power, grounds and all limits in the original before wiring; assignments differ between models and hardware revisions.

Connector A

PinChannel NamePinChannel Name
1Injection Channel 129Lambda 2 Heater +
2Injection Channel 230Lambda 2 Heater -
3Injection Channel 331Digital Input Ground Out
4Injection Channel 432Ignition Channel 1
5Injection Channel 533Ignition Channel 2
6Injection Channel 634Ignition Channel 3
7Injection Channel 735Ignition Channel 4
8Injection Channel 836Ignition Channel 5
9Injection Channel 937Ignition Channel 6
10Injection Channel 1038Ignition Channel 7
11Injection Channel 1139Ignition Channel 8
12Injection Channel 1240Ignition Channel 9
13Injection Channel 1341Ignition Channel 10
14Injection Channel 1442Ignition Channel 11
15Injection Channel 1543Ignition Channel 12
16Injection Channel 1644Digital Input 3
17Lambda 1 Nernst Cell (Vs)45Digital Input 2
18Lambda 1 Cal Resistor (CalR)46Digital Input 1
19Lambda 1 Pump Cell (Ip)47Digital Input 9
20Lambda 1 Virtual Ground (VGnd)48Digital Input 8
21Lambda 1 Heater +49Digital Input 7
22Lambda 1 Heater -50Digital Input 6
23Digital Input 1351Digital Input 5
24Digital Input 1452Digital Input 4
25Lambda 2 Pump Cell (Ip)53Digital Input 10
26Lambda 2 Virtual Ground (VGnd)54Digital Input 11
27Lambda 2 Nernst Cell (Vs)55Digital Input 12
28Lambda 2 Cal Resistor (CalR)

Connector B

PinChannel Name
AECU 14V Supply
BECU 14V Supply
CECU 14V Supply
DECU Ground
EECU Ground
FAuxiliary Output 16
GAuxiliary Output 15
HAuxiliary Output 14
JAuxiliary Output 12
KAuxiliary Output 10
LAuxiliary Output 8
MAuxiliary Output 7
NAuxiliary Output 5
PAuxiliary Output 3
RAuxiliary Output 1
SAuxiliary Output 2
TECU 14V Supply
UECU Ground
VECU Ground
WAuxiliary Output 13
XAuxiliary Output 11
YAuxiliary Output 9
ZAuxiliary Output 6
aAuxiliary Output 4
bECU Ground
cECU Ground

Connector C

PinChannel NamePinChannel Name
1Analog Input Channel 129Analog Sensor 0V Reference
2Analog Input Channel 230Analog Sensor 0V Reference
3Analog Input Channel 331Analog Sensor 0V Reference
4Analog Input Channel 432Knock 2 +
5Analog Input Channel 533Analog Out
6Analog Input Channel 634CAN 2L
7Analog Input Channel 735CAN 2H
8Analog Input Channel 836CAN 1L
9Analog Input Channel 937CAN 1H
10Analog Input Channel 1038Sensor Supply Vref2: 5.0V
11Analog Input Channel 1139Sensor Supply Vref2: 5.0V
12Analog Input Channel 1240Knock 1 -
13Analog Input Channel 1341Sync Sensor -
14Analog Input Channel 1442Sync Sensor +
15Analog Input Channel 1543Crank Index Sensor -
16Analog Input Channel 1644Crank Index Sensor +
17Analog Input Channel 1745Sensor Supply Vref1: 5.0V
18Analog Input Channel 1846Sensor Supply Vref1: 5.0V
19Analog Input Channel 1947Knock 1 +
20Analog Input Channel 2048Ethernet Tx +
21Analog Input Channel 2149Ethernet Tx -
22Analog Input Channel 2250Ethernet Rx +
23Analog Input Channel 2351Ethernet Rx -
24Analog Input Channel 2452Sensor Supply 8V
25Knock 2 -53Constant 14V Supply(Backup)
26SHIELD (Crank/Cam/ Knock)54Sensor Supply Vref3: 5.0V
27SHIELD (Crank/Cam/ Knock)55Sensor Supply Vref3: 5.0V
28Analog Sensor 0V Reference

Sensor 0 V references and main ECU grounds have distinct wiring requirements. H-bridge supplies and relay control require the installation described in the manufacturer's power-distribution guide. See Emtron wiring index and revision-specific diagrams.

Documentation and setup

Revision 2: Emtron KV16M
Emtron KV16M ECU
Emtron KV16M product image, courtesy of Emtron; reproduced with permission.

Emtron KV16M is a programmable standalone ECU from Emtron Australia. Sixteen fuel and twelve sequential ignition channels are listed. The KV16M has a 136-way Deutsch Autosport connector system, distinct from the Superseal KV16. Emtron KV16M datasheet.

Identification and configuration

Record the ECU model, serial, board revision and loaded firmware. The Emtune calibration determines the use of configurable inputs and outputs; electrical limits, ignition driver type, injector impedance and wired supplies must be checked for the actual unit. Emtron engine-management manual.

Connector pinouts

These tables reproduce the positions in Emtron's KV16M pinout. The source diagrams are viewed looking into the ECU connector. NC is the manufacturer's unconnected designation. Verify connector keying, revision, power, grounds and all limits in the original before wiring; assignments differ between models and hardware revisions.

Connector A

PinChannel NamePinChannel Name
1Injection Channel 129Lambda 2 Heater +
2Injection Channel 230Lambda 2 Heater -
3Injection Channel 331Digital Input Ground Out
4Injection Channel 432Ignition Channel 1
5Injection Channel 533Ignition Channel 2
6Injection Channel 634Ignition Channel 3
7Injection Channel 735Ignition Channel 4
8Injection Channel 836Ignition Channel 5
9Injection Channel 937Ignition Channel 6
10Injection Channel 1038Ignition Channel 7
11Injection Channel 1139Ignition Channel 8
12Injection Channel 1240Ignition Channel 9
13Injection Channel 1341Ignition Channel 10
14Injection Channel 1442Ignition Channel 11
15Injection Channel 1543Ignition Channel 12
16Injection Channel 1644Digital Input 3
17Lambda 1 Nernst Cell (Vs)45Digital Input 2
18Lambda 1 Cal Resistor (CalR)46Digital Input 1
19Lambda 1 Pump Cell (Ip)47Digital Input 9
20Lambda 1 Virtual Ground (VGnd)48Digital Input 8
21Lambda 1 Heater +49Digital Input 7
22Lambda 1 Heater -50Digital Input 6
23Digital Input 1351Digital Input 5
24Digital Input 1452Digital Input 4
25Lambda 2 Pump Cell (Ip)53Digital Input 10
26Lambda 2 Virtual Ground (VGnd)54Digital Input 11
27Lambda 2 Nernst Cell (Vs)55Digital Input 12
28Lambda 2 Cal Resistor (CalR)

Connector B

PinChannel Name
AECU 14V Supply
BECU 14V Supply
CECU 14V Supply
DECU Ground
EECU Ground
FAuxiliary Output 16
GAuxiliary Output 15
HAuxiliary Output 14
JAuxiliary Output 12
KAuxiliary Output 10
LAuxiliary Output 8
MAuxiliary Output 7
NAuxiliary Output 5
PAuxiliary Output 3
RAuxiliary Output 1
SAuxiliary Output 2
TECU 14V Supply
UECU Ground
VECU Ground
WAuxiliary Output 13
XAuxiliary Output 11
YAuxiliary Output 9
ZAuxiliary Output 6
aAuxiliary Output 4
bECU Ground
cECU Ground

Connector C

PinChannel NamePinChannel Name
1Analog Input Channel 129Analog Sensor 0V Reference
2Analog Input Channel 230Analog Sensor 0V Reference
3Analog Input Channel 331Analog Sensor 0V Reference
4Analog Input Channel 432Knock 2 +
5Analog Input Channel 533Analog Out
6Analog Input Channel 634CAN 2L
7Analog Input Channel 735CAN 2H
8Analog Input Channel 836CAN 1L
9Analog Input Channel 937CAN 1H
10Analog Input Channel 1038Sensor Supply Vref2: 5.0V
11Analog Input Channel 1139Sensor Supply Vref2: 5.0V
12Analog Input Channel 1240Knock 1 -
13Analog Input Channel 1341Sync Sensor -
14Analog Input Channel 1442Sync Sensor +
15Analog Input Channel 1543Crank Index Sensor -
16Analog Input Channel 1644Crank Index Sensor +
17Analog Input Channel 1745Sensor Supply Vref1: 5.0V
18Analog Input Channel 1846Sensor Supply Vref1: 5.0V
19Analog Input Channel 1947Knock 1 +
20Analog Input Channel 2048Ethernet Tx +
21Analog Input Channel 2149Ethernet Tx -
22Analog Input Channel 2250Ethernet Rx +
23Analog Input Channel 2351Ethernet Rx -
24Analog Input Channel 2452Sensor Supply 8V
25Knock 2 -53Constant 14V Supply(Backup)
26SHIELD (Crank/Cam/ Knock)54Sensor Supply Vref3: 5.0V
27SHIELD (Crank/Cam/ Knock)55Sensor Supply Vref3: 5.0V
28Analog Sensor 0V Reference

Sensor 0 V references and main ECU grounds have distinct wiring requirements. H-bridge supplies and relay control require the installation described in the manufacturer's power-distribution guide. See Emtron wiring index and revision-specific diagrams.

Documentation and setup