Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
Emtron standalone ECUs
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None
Emtron KV16M ECU
Emtron KV16M product image, courtesy of Emtron; reproduced with permission.

Emtron KV16M is a programmable standalone ECU from Emtron Australia. Sixteen fuel and twelve sequential ignition channels are listed. The KV16M has a 136-way Deutsch Autosport connector system, distinct from the Superseal KV16. Emtron KV16M datasheet.

Identification and configuration

Record the ECU model, serial, board revision and loaded firmware. The Emtune calibration determines the use of configurable inputs and outputs; electrical limits, ignition driver type, injector impedance and wired supplies must be checked for the actual unit. Emtron engine-management manual.

Connector pinouts

These tables reproduce the positions in Emtron's KV16M pinout. The source diagrams are viewed looking into the ECU connector. NC is the manufacturer's unconnected designation. Verify connector keying, revision, power, grounds and all limits in the original before wiring; assignments differ between models and hardware revisions.

Connector A

PinChannel NamePinChannel Name
1Injection Channel 129Lambda 2 Heater +
2Injection Channel 230Lambda 2 Heater -
3Injection Channel 331Digital Input Ground Out
4Injection Channel 432Ignition Channel 1
5Injection Channel 533Ignition Channel 2
6Injection Channel 634Ignition Channel 3
7Injection Channel 735Ignition Channel 4
8Injection Channel 836Ignition Channel 5
9Injection Channel 937Ignition Channel 6
10Injection Channel 1038Ignition Channel 7
11Injection Channel 1139Ignition Channel 8
12Injection Channel 1240Ignition Channel 9
13Injection Channel 1341Ignition Channel 10
14Injection Channel 1442Ignition Channel 11
15Injection Channel 1543Ignition Channel 12
16Injection Channel 1644Digital Input 3
17Lambda 1 Nernst Cell (Vs)45Digital Input 2
18Lambda 1 Cal Resistor (CalR)46Digital Input 1
19Lambda 1 Pump Cell (Ip)47Digital Input 9
20Lambda 1 Virtual Ground (VGnd)48Digital Input 8
21Lambda 1 Heater +49Digital Input 7
22Lambda 1 Heater -50Digital Input 6
23Digital Input 1351Digital Input 5
24Digital Input 1452Digital Input 4
25Lambda 2 Pump Cell (Ip)53Digital Input 10
26Lambda 2 Virtual Ground (VGnd)54Digital Input 11
27Lambda 2 Nernst Cell (Vs)55Digital Input 12
28Lambda 2 Cal Resistor (CalR)

Connector B

PinChannel Name
AECU 14V Supply
BECU 14V Supply
CECU 14V Supply
DECU Ground
EECU Ground
FAuxiliary Output 16
GAuxiliary Output 15
HAuxiliary Output 14
JAuxiliary Output 12
KAuxiliary Output 10
LAuxiliary Output 8
MAuxiliary Output 7
NAuxiliary Output 5
PAuxiliary Output 3
RAuxiliary Output 1
SAuxiliary Output 2
TECU 14V Supply
UECU Ground
VECU Ground
WAuxiliary Output 13
XAuxiliary Output 11
YAuxiliary Output 9
ZAuxiliary Output 6
aAuxiliary Output 4
bECU Ground
cECU Ground

Connector C

PinChannel NamePinChannel Name
1Analog Input Channel 129Analog Sensor 0V Reference
2Analog Input Channel 230Analog Sensor 0V Reference
3Analog Input Channel 331Analog Sensor 0V Reference
4Analog Input Channel 432Knock 2 +
5Analog Input Channel 533Analog Out
6Analog Input Channel 634CAN 2L
7Analog Input Channel 735CAN 2H
8Analog Input Channel 836CAN 1L
9Analog Input Channel 937CAN 1H
10Analog Input Channel 1038Sensor Supply Vref2: 5.0V
11Analog Input Channel 1139Sensor Supply Vref2: 5.0V
12Analog Input Channel 1240Knock 1 -
13Analog Input Channel 1341Sync Sensor -
14Analog Input Channel 1442Sync Sensor +
15Analog Input Channel 1543Crank Index Sensor -
16Analog Input Channel 1644Crank Index Sensor +
17Analog Input Channel 1745Sensor Supply Vref1: 5.0V
18Analog Input Channel 1846Sensor Supply Vref1: 5.0V
19Analog Input Channel 1947Knock 1 +
20Analog Input Channel 2048Ethernet Tx +
21Analog Input Channel 2149Ethernet Tx -
22Analog Input Channel 2250Ethernet Rx +
23Analog Input Channel 2351Ethernet Rx -
24Analog Input Channel 2452Sensor Supply 8V
25Knock 2 -53Constant 14V Supply(Backup)
26SHIELD (Crank/Cam/ Knock)54Sensor Supply Vref3: 5.0V
27SHIELD (Crank/Cam/ Knock)55Sensor Supply Vref3: 5.0V
28Analog Sensor 0V Reference

Sensor 0 V references and main ECU grounds have distinct wiring requirements. H-bridge supplies and relay control require the installation described in the manufacturer's power-distribution guide. See Emtron wiring index and revision-specific diagrams.

Documentation and setup