Removed text is struck through; added text is highlighted.
MoTeC M170 product image from the manufacturer datasheet; reproduced with permission.
MoTeC M170 is an M1-family programmable ECU, part 13170. The manufacturer identifies it for up to 8 cylinders and port injection. M1 hardware is paired with a software package; features, channels and licences depend on the loaded package and hardware revision. MoTeC M170 product information and product image.
Identification and inputs/outputs
FieldManufacturer comparisonInjection hardware8 port injector outputs; 2 low-side injector outputsIgnition8 low-side ignition outputsHalf-bridge outputs6Universal digital inputs8Analogue voltage / temperature inputs8 / 4CAN buses1Connector configurationone Autosport, 66 positions
Numbers describe hardware capacity; they do not establish simultaneous availability for a specific application. MoTeC’s M1 comparison distinguishes port, inductive direct and piezo direct drivers. Check the exact injector and package; an external driver is not interchangeable with an internal driver.
Wiring and pinout
Use the M170 connector pinout and datasheet on the manufacturer product page. Connector type, keying and positions vary across M1 models; do not copy pin functions from another ECU. Verify the hardware revision, package, output allocations, wiring orientation, electrical limits and power and earth provisions against the exact unit.
A structured, redrawn version of the manufacturer pin table is in MoTeC M170 connector pinout.Manufacturer connector tablesThese tables reproduce the complete connector position and designation lists from the MoTeC M170 datasheet. Pin identifiers are kept as printed, including letter case. Check the original connector views, mating key, wire size, electrical ratings and hardware revision before connecting. Output functions depend on the ECU package and configuration; direct-injection models require their specified drivers and precautions.Connector A — 66 positionsPinDesignationFunctionA01IGN_LS1Low Side Ignition 1A02IGN_LS8Low Side Ignition 8A03IGN_LS7Low Side Ignition 7A04IGN_LS3Low Side Ignition 3A05IGN_LS2Low Side Ignition 2A06AV3Analogue Voltage Input 3A07AV4Analogue Voltage Input 4A08OUT_HB2Half Bridge Output 2A09OUT_HB1Half Bridge Output 1A10IGN_LS4Low Side Ignition 4A11SEN_0V_ASensor 0V AA12AV5Analogue Voltage Input 5A13UDIG7Universal Digital Input 7A14BAT_NEG1Battery NegativeA15BAT_NEG2Battery NegativeA16SEN_5V0_ASensor 5.0V AA17IGN_LS5Low Side Ignition 5A18AV2Analogue Voltage Input 2A19BAT_NEG3Battery NegativeA20BAT_NEG4Battery NegativeA21BAT_NEG5Battery NegativeA22UDIG8Universal Digital Input 8A23BAT_POSBattery PositiveA24INJ_PH5Peak Hold Injector 5A25IGN_LS6Low Side Ignition 6A26AV1Analogue Voltage Input 1A27SEN_0V_BSensor 0V BA28AT1Analogue Temperature Input 1A29KNOCK1Knock Input 1A30AT3Analogue Temperature Input 3A31CAN_LOCAN Bus 1 LowA32BAT_POSBattery PositiveA33INJ_PH1Peak Hold Injector 1A34SEN_5V0_BSensor 5.0V BA35AV7Analogue Voltage Input 7A36AV6Analogue Voltage Input 6A37SEN_6V3Sensor 6.3VA38AT2Analogue Temperature Input 2A39AT4Analogue Temperature Input 4A40CAN_HICAN Bus 1 HighA41BAT_POSBattery PositiveA42INJ_PH6Peak Hold Injector 6A43INJ_LS1Low Side Injector 1A44AV8Analogue Voltage Input 8A45UDIG4Universal Digital Input 4A46UDIG3Universal Digital Input 3A47ETH_TX-Ethernet Transmit-A48ETH_TX+Ethernet Transmit+A49UDIG1Universal Digital Input 1A50INJ_PH2Peak Hold Injector 2A51INJ_LS2Low Side Injector 2A52UDIG5Universal Digital Input 5A53UDIG6Universal Digital Input 6A54BAT_BAKBattery BackupA55ETH_RX+Ethernet Receive+A56UDIG2Universal Digital Input 2A57INJ_PH7Peak Hold Injector 7A58OUT_HB5Half Bridge Output 5A59OUT_HB3Half Bridge Output 3A60KNOCK2Knock Input 2A61ETH_RX-Ethernet Receive-A62INJ_PH8Peak Hold Injector 8A63INJ_PH3Peak Hold Injector 3A64OUT_HB6Half Bridge Output 6A65OUT_HB4Half Bridge Output 4A66INJ_PH4Peak Hold Injector 4
Software and context
M1 Tune configures supported packages, while M1 Build is used to develop packages. ECU and logging features depend on installed licences. MoTeC downloads; MoTeC model index.
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 2: MoTeC M170MoTeC M170 product image from the manufacturer datasheet; reproduced with permission.
MoTeC M170 is an M1-family programmable ECU, part 13170. The manufacturer identifies it for up to 8 cylinders and port injection. M1 hardware is paired with a software package; features, channels and licences depend on the loaded package and hardware revision. MoTeC M170 product information and product image.
Identification and inputs/outputs
Field
Manufacturer comparison
Injection hardware
8 port injector outputs; 2 low-side injector outputs
Ignition
8 low-side ignition outputs
Half-bridge outputs
6
Universal digital inputs
8
Analogue voltage / temperature inputs
8 / 4
CAN buses
1
Connector configuration
one Autosport, 66 positions
Numbers describe hardware capacity; they do not establish simultaneous availability for a specific application. MoTeC’s M1 comparison distinguishes port, inductive direct and piezo direct drivers. Check the exact injector and package; an external driver is not interchangeable with an internal driver.
Wiring and pinout
Use the M170 connector pinout and datasheet on the manufacturer product page. Connector type, keying and positions vary across M1 models; do not copy pin functions from another ECU. Verify the hardware revision, package, output allocations, wiring orientation, electrical limits and power and earth provisions against the exact unit.
Software and context
M1 Tune configures supported packages, while M1 Build is used to develop packages. ECU and logging features depend on installed licences. MoTeC downloads; MoTeC model index.
Revision 4: MoTeC M170MoTeC M170 product image from the manufacturer datasheet; reproduced with permission.
MoTeC M170 is an M1-family programmable ECU, part 13170. The manufacturer identifies it for up to 8 cylinders and port injection. M1 hardware is paired with a software package; features, channels and licences depend on the loaded package and hardware revision. MoTeC M170 product information and product image.
Identification and inputs/outputs
Field
Manufacturer comparison
Injection hardware
8 port injector outputs; 2 low-side injector outputs
Ignition
8 low-side ignition outputs
Half-bridge outputs
6
Universal digital inputs
8
Analogue voltage / temperature inputs
8 / 4
CAN buses
1
Connector configuration
one Autosport, 66 positions
Numbers describe hardware capacity; they do not establish simultaneous availability for a specific application. MoTeC’s M1 comparison distinguishes port, inductive direct and piezo direct drivers. Check the exact injector and package; an external driver is not interchangeable with an internal driver.
Wiring and pinout
Use the M170 connector pinout and datasheet on the manufacturer product page. Connector type, keying and positions vary across M1 models; do not copy pin functions from another ECU. Verify the hardware revision, package, output allocations, wiring orientation, electrical limits and power and earth provisions against the exact unit.
These tables reproduce the complete connector position and designation lists from the MoTeC M170 datasheet. Pin identifiers are kept as printed, including letter case. Check the original connector views, mating key, wire size, electrical ratings and hardware revision before connecting. Output functions depend on the ECU package and configuration; direct-injection models require their specified drivers and precautions.
Connector A — 66 positions
Pin
Designation
Function
A01
IGN_LS1
Low Side Ignition 1
A02
IGN_LS8
Low Side Ignition 8
A03
IGN_LS7
Low Side Ignition 7
A04
IGN_LS3
Low Side Ignition 3
A05
IGN_LS2
Low Side Ignition 2
A06
AV3
Analogue Voltage Input 3
A07
AV4
Analogue Voltage Input 4
A08
OUT_HB2
Half Bridge Output 2
A09
OUT_HB1
Half Bridge Output 1
A10
IGN_LS4
Low Side Ignition 4
A11
SEN_0V_A
Sensor 0V A
A12
AV5
Analogue Voltage Input 5
A13
UDIG7
Universal Digital Input 7
A14
BAT_NEG1
Battery Negative
A15
BAT_NEG2
Battery Negative
A16
SEN_5V0_A
Sensor 5.0V A
A17
IGN_LS5
Low Side Ignition 5
A18
AV2
Analogue Voltage Input 2
A19
BAT_NEG3
Battery Negative
A20
BAT_NEG4
Battery Negative
A21
BAT_NEG5
Battery Negative
A22
UDIG8
Universal Digital Input 8
A23
BAT_POS
Battery Positive
A24
INJ_PH5
Peak Hold Injector 5
A25
IGN_LS6
Low Side Ignition 6
A26
AV1
Analogue Voltage Input 1
A27
SEN_0V_B
Sensor 0V B
A28
AT1
Analogue Temperature Input 1
A29
KNOCK1
Knock Input 1
A30
AT3
Analogue Temperature Input 3
A31
CAN_LO
CAN Bus 1 Low
A32
BAT_POS
Battery Positive
A33
INJ_PH1
Peak Hold Injector 1
A34
SEN_5V0_B
Sensor 5.0V B
A35
AV7
Analogue Voltage Input 7
A36
AV6
Analogue Voltage Input 6
A37
SEN_6V3
Sensor 6.3V
A38
AT2
Analogue Temperature Input 2
A39
AT4
Analogue Temperature Input 4
A40
CAN_HI
CAN Bus 1 High
A41
BAT_POS
Battery Positive
A42
INJ_PH6
Peak Hold Injector 6
A43
INJ_LS1
Low Side Injector 1
A44
AV8
Analogue Voltage Input 8
A45
UDIG4
Universal Digital Input 4
A46
UDIG3
Universal Digital Input 3
A47
ETH_TX-
Ethernet Transmit-
A48
ETH_TX+
Ethernet Transmit+
A49
UDIG1
Universal Digital Input 1
A50
INJ_PH2
Peak Hold Injector 2
A51
INJ_LS2
Low Side Injector 2
A52
UDIG5
Universal Digital Input 5
A53
UDIG6
Universal Digital Input 6
A54
BAT_BAK
Battery Backup
A55
ETH_RX+
Ethernet Receive+
A56
UDIG2
Universal Digital Input 2
A57
INJ_PH7
Peak Hold Injector 7
A58
OUT_HB5
Half Bridge Output 5
A59
OUT_HB3
Half Bridge Output 3
A60
KNOCK2
Knock Input 2
A61
ETH_RX-
Ethernet Receive-
A62
INJ_PH8
Peak Hold Injector 8
A63
INJ_PH3
Peak Hold Injector 3
A64
OUT_HB6
Half Bridge Output 6
A65
OUT_HB4
Half Bridge Output 4
A66
INJ_PH4
Peak Hold Injector 4
Software and context
M1 Tune configures supported packages, while M1 Build is used to develop packages. ECU and logging features depend on installed licences. MoTeC downloads; MoTeC model index.