Removed text is struck through; added text is highlighted.
ME442 Mazda MX-5 Mk2 1999–2000 plug-in ECU. Manufacturer product image: Motorsport Electronics; used with permission.
ME442 plug-in ECU for Mazda MX-5 Mk2 1999–2000. This application-specific unit replaces the factory ECU electronics while using the vehicle's original harness connector, subject to exact fitment and configuration. Motorsport Electronics product information · application installation guide.
Identification and application
The manufacturer identifies this as the NB three-plug application. Verify the original board and connector and use the matching base map and board-switch configuration. Record the serial, board version, firmware, factory ECU part number, engine and transmission before installing. The ME221 and ME442 are separate hardware choices; the manufacturer lists wideband, onboard logging and EGT as ME442 plug-in features. Optional electronic throttle equipment and supported functions vary by board and configuration. See ME's model comparison and downloads.
Connector and pinout
Use the OEM header and auxiliary connector diagrams in the exact application installation guide. Connector view, jumper/switch settings, sensors and supported functions vary by generation and vehicle. The universal 28-way and 90-way wire-in tables do not define this plug-in board's factory header.
OEM header assignmentsDocumented positions from the manufacturer application guide, looking into the ECU connector from the loom wire side. Positions not shown in that guide are not asserted here. Functions and auxiliary DBW availability depend on model, board revision, hardware and configuration.PinFunction in manufacturer guide1BIgnition 12 V1ECEL / LS131iAC blower relay / LS161KDBW motor +, auxiliary, optional ME442 DBW only1NDBW motor −, auxiliary, optional ME442 DBW only1OAlternator control / LS4 (R1.4), COIL 8 (R1.5), COIL 5 (R1.8 onwards)1PAir-con switch / DIGIN 51QBattery light / LS121RPrimary fan relay / LS151SAC clutch relay / LS142BInlet-air temperature / ANA T12CO2 sensor / ANA V32DVSS speed / DIGIN 42ECoolant sensor / ANA T22FKnock sensor + / KNOCK 12HCam sensor / VR_CAMA2iTPS 5 V reference2JCrank sensor / VR_CRANK2KTachometer2LMAF signal / ANA V43A/B/CGrounds3EThrottle signal / ANA V23GIgnition 1 & 4 / COIL 13HIgnition 2 & 3 / COIL 23iClutch switch / DIGIN 6, not all models3LPurge solenoid / boost / LS103N/3PFuel pump relay / LS113OPWM idle valve / LS93QVICS solenoid / LS173WInjector 13XInjector 23YInjector 33ZInjector 4MAPOn-board MAP / ANA V1The guide lists several board-revision alternatives for alternator control at 1O; its footnote describes R1.5-and-later IGN 8 while its table lists COIL 5 for R1.8 onwards. Confirm the actual board with ME.Auxiliary connector assignmentsThe ME GEN2 installation guide lists this 20-way Molex Mini-Fit Jr connector. Check the original diagram for orientation, the actual model and fitted options: the table describes the documented connector, not a guarantee every function is supported on every ME221 or ME442 core.PinFunction in manufacturer guide1Injector 5 — 3.5 A FB protected2Injector 6 — 3.5 A FB protected3Injector 7 — 3.5 A FB protected4Injector 8 — 3.5 A FB protected5Coil 3 — 50 mA TTL6Coil 4 — 50 mA TTL7LS1 — 2 A PWM-capable8LS2 — 2 A PWM-capable9LS3 — 2 A PWM-capable10K-type EGT signal — ME442 only11DI 1 — 1 kΩ 5 V pull-up12DI 2 — 1 kΩ 5 V pull-up13DI 3 — 1 kΩ 5 V pull-up14Analogue volt 5 — 0–5 V15Analogue volt 6 — 0–5 V16Analogue volt 7 — 0–5 V17CAN 1 low18CAN 1 high195 V reference — 100 mA max20EGT and sensor groundThe guide calls pin 13 “DI 3” but describes it as “Digital Input 2” in parentheses; the inconsistency is retained here as DI 3 and requires confirmation.
Software and installation
Use the correct MEITE / EZ Tune release and the model-specific firmware and base map. The installation guide covers sensor settings, baseline checks, expansion, jumper settings and any vehicle-specific exceptions; a base map still needs calibration and verification on the actual engine. See the ME442 family page for wire-in generation and hardware context.
Sources reviewed 17 November 2026.
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 2: Motorsport Electronics ME442 Mazda MX-5 Mk2 1999–2000 plug-inME442 Mazda MX-5 Mk2 1999–2000 plug-in ECU. Manufacturer product image: Motorsport Electronics; used with permission.
ME442 plug-in ECU for Mazda MX-5 Mk2 1999–2000. This application-specific unit replaces the factory ECU electronics while using the vehicle's original harness connector, subject to exact fitment and configuration. Motorsport Electronics product information · application installation guide.
Identification and application
The manufacturer identifies this as the NB three-plug application. Verify the original board and connector and use the matching base map and board-switch configuration. Record the serial, board version, firmware, factory ECU part number, engine and transmission before installing. The ME221 and ME442 are separate hardware choices; the manufacturer lists wideband, onboard logging and EGT as ME442 plug-in features. Optional electronic throttle equipment and supported functions vary by board and configuration. See ME's model comparison and downloads.
Connector and pinout
Use the OEM header and auxiliary connector diagrams in the exact application installation guide. Connector view, jumper/switch settings, sensors and supported functions vary by generation and vehicle. The universal 28-way and 90-way wire-in tables do not define this plug-in board's factory header.
Software and installation
Use the correct MEITE / EZ Tune release and the model-specific firmware and base map. The installation guide covers sensor settings, baseline checks, expansion, jumper settings and any vehicle-specific exceptions; a base map still needs calibration and verification on the actual engine. See the ME442 family page for wire-in generation and hardware context.
Sources reviewed 17 November 2026.
Revision 3: Motorsport Electronics ME442 Mazda MX-5 Mk2 1999–2000 plug-inME442 Mazda MX-5 Mk2 1999–2000 plug-in ECU. Manufacturer product image: Motorsport Electronics; used with permission.
ME442 plug-in ECU for Mazda MX-5 Mk2 1999–2000. This application-specific unit replaces the factory ECU electronics while using the vehicle's original harness connector, subject to exact fitment and configuration. Motorsport Electronics product information · application installation guide.
Identification and application
The manufacturer identifies this as the NB three-plug application. Verify the original board and connector and use the matching base map and board-switch configuration. Record the serial, board version, firmware, factory ECU part number, engine and transmission before installing. The ME221 and ME442 are separate hardware choices; the manufacturer lists wideband, onboard logging and EGT as ME442 plug-in features. Optional electronic throttle equipment and supported functions vary by board and configuration. See ME's model comparison and downloads.
Connector and pinout
Use the OEM header and auxiliary connector diagrams in the exact application installation guide. Connector view, jumper/switch settings, sensors and supported functions vary by generation and vehicle. The universal 28-way and 90-way wire-in tables do not define this plug-in board's factory header.
OEM header assignments
Documented positions from the manufacturer application guide, looking into the ECU connector from the loom wire side. Positions not shown in that guide are not asserted here. Functions and auxiliary DBW availability depend on model, board revision, hardware and configuration.
The guide lists several board-revision alternatives for alternator control at 1O; its footnote describes R1.5-and-later IGN 8 while its table lists COIL 5 for R1.8 onwards. Confirm the actual board with ME.
Auxiliary connector assignments
The ME GEN2 installation guide lists this 20-way Molex Mini-Fit Jr connector. Check the original diagram for orientation, the actual model and fitted options: the table describes the documented connector, not a guarantee every function is supported on every ME221 or ME442 core.
Pin
Function in manufacturer guide
1
Injector 5 — 3.5 A FB protected
2
Injector 6 — 3.5 A FB protected
3
Injector 7 — 3.5 A FB protected
4
Injector 8 — 3.5 A FB protected
5
Coil 3 — 50 mA TTL
6
Coil 4 — 50 mA TTL
7
LS1 — 2 A PWM-capable
8
LS2 — 2 A PWM-capable
9
LS3 — 2 A PWM-capable
10
K-type EGT signal — ME442 only
11
DI 1 — 1 kΩ 5 V pull-up
12
DI 2 — 1 kΩ 5 V pull-up
13
DI 3 — 1 kΩ 5 V pull-up
14
Analogue volt 5 — 0–5 V
15
Analogue volt 6 — 0–5 V
16
Analogue volt 7 — 0–5 V
17
CAN 1 low
18
CAN 1 high
19
5 V reference — 100 mA max
20
EGT and sensor ground
The guide calls pin 13 “DI 3” but describes it as “Digital Input 2” in parentheses; the inconsistency is retained here as DI 3 and requires confirmation.
Software and installation
Use the correct MEITE / EZ Tune release and the model-specific firmware and base map. The installation guide covers sensor settings, baseline checks, expansion, jumper settings and any vehicle-specific exceptions; a base map still needs calibration and verification on the actual engine. See the ME442 family page for wire-in generation and hardware context.