Removed text is struck through; added text is highlighted.
ME221 Mazda MX-5 Mk1 1989–1995 plug-in ECU. Manufacturer product image: Motorsport Electronics; used with permission.
ME221 plug-in ECU for Mazda MX-5 Mk1 1989–1995. This application-specific unit replaces the factory ECU electronics while using the vehicle's original harness connector, subject to exact fitment and configuration. Motorsport Electronics product information · application installation guide.
Identification and application
The manufacturer identifies this as its early two-plug NA application. Later Mk1 cars can use a three-plug ECU; check the original connector before selecting the board. Record the serial, board version, firmware, factory ECU part number, engine and transmission before installing. The ME221 and ME442 are separate hardware choices; the manufacturer lists wideband, onboard logging and EGT as ME442 plug-in features. Optional electronic throttle equipment and supported functions vary by board and configuration. See ME's model comparison and downloads.
Connector and pinout
Use the OEM header and auxiliary connector diagrams in the exact application installation guide. Connector view, jumper/switch settings, sensors and supported functions vary by generation and vehicle. The universal 28-way and 90-way wire-in tables do not define this plug-in board's factory header.
OEM header assignmentsDocumented positions from the manufacturer application guide, looking into the ECU connector from the loom wire side. Positions not shown in that guide are not asserted here. Functions and auxiliary DBW availability depend on model, board revision, hardware and configuration.PinFunction in manufacturer guide1BIgnition 12 V1CFuel pump (early)1DLS4 spare / LS41ECEL / LS111FAlternative tachometer output; see appendix C1GIgnition 1 & 4 / COIL 11HIgnition 2 & 3 / COIL 21iDBW motor − (auxiliary; ME442 optional DBW)1JAir-con relay / LS151KEGT K-type + / EGT11LPrimary fan relay, 1.8 engines / LS121MVSS speed / DIGIN 41NVTPS 5 V reference via VTPS DIP switch1QAir-con switch / DIGIN 51RPrimary fan relay, 1.6 engines / LS131VClutch switch / DIGIN 62A/B/C/DGrounds2ECAS sensor signal / VR_CRANK2GCAS sensor signal / VR_CAMA2i12 V output for four-pin coil-pack-driven tacho2K5 V reference2LTPS signal / ANA V22M>94 TPS signal2NO2 sensor signal / ANA V32OAirflow signal / ANA V42PInlet air temperature / ANA T12QCoolant sensor / ANA T22SAir-con blower relay (1995) / LS162RDBW +2TFuel pump relay (1993+) / LS142UInjector 1 (& 3 before 1993)2VInjector 2 (& 4 before 1993)2WPWM idle valve / LS92XPurge / boost solenoid / LS102YInjector 32ZInjector 4MAPOn-board MAP sensor / ANA V1Auxiliary connector assignmentsThe ME GEN2 installation guide lists this 20-way Molex Mini-Fit Jr connector. Check the original diagram for orientation, the actual model and fitted options: the table describes the documented connector, not a guarantee every function is supported on every ME221 or ME442 core.PinFunction in manufacturer guide1Injector 5 — 3.5 A FB protected2Injector 6 — 3.5 A FB protected3Injector 7 — 3.5 A FB protected4Injector 8 — 3.5 A FB protected5Coil 3 — 50 mA TTL6Coil 4 — 50 mA TTL7LS1 — 2 A PWM-capable8LS2 — 2 A PWM-capable9LS3 — 2 A PWM-capable10Knock signal11DI 1 — 1 kΩ 5 V pull-up12DI 2 — 1 kΩ 5 V pull-up13DI 3 — 1 kΩ 5 V pull-up14Analogue volt 5 — 0–5 V15Analogue volt 6 — 0–5 V16Analogue volt 7 — 0–5 V17CAN 1 low — 120 Ω terminated18CAN 1 high — 120 Ω terminated195 V reference — 100 mA max20Knock and sensor groundThe guide asks users to contact ME for EGT connection on this 1989–95 application.Structured connector pinoutEvery cavity of the factory two-plug header and the 20-way auxiliary connector, with the manufacturer's assignments, is drawn in Motorsport Electronics ME221 and ME442 Mazda MX-5 1989-1995 plug-in connector pinout.ProcessorMotorsport Electronics does not publish the microcontroller part number. A distributor specification sheet for the ME221 lists a 120 MHz 32-bit RISC processor; this is a vendor specification rather than a component identification. ATP Turbo ME221 specification sheet (May 2023), accessed 19 November 2026.
Software and installation
Use the correct MEITE / EZ Tune release and the model-specific firmware and base map. The installation guide covers sensor settings, baseline checks, expansion, jumper settings and any vehicle-specific exceptions; a base map still needs calibration and verification on the actual engine. See the ME221 family page for wire-in generation and hardware context.
Sources reviewed 17 November 2026.
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 2: Motorsport Electronics ME221 Mazda MX-5 Mk1 1989–1995 plug-inME221 Mazda MX-5 Mk1 1989–1995 plug-in ECU. Manufacturer product image: Motorsport Electronics; used with permission.
ME221 plug-in ECU for Mazda MX-5 Mk1 1989–1995. This application-specific unit replaces the factory ECU electronics while using the vehicle's original harness connector, subject to exact fitment and configuration. Motorsport Electronics product information · application installation guide.
Identification and application
The manufacturer identifies this as its early two-plug NA application. Later Mk1 cars can use a three-plug ECU; check the original connector before selecting the board. Record the serial, board version, firmware, factory ECU part number, engine and transmission before installing. The ME221 and ME442 are separate hardware choices; the manufacturer lists wideband, onboard logging and EGT as ME442 plug-in features. Optional electronic throttle equipment and supported functions vary by board and configuration. See ME's model comparison and downloads.
Connector and pinout
Use the OEM header and auxiliary connector diagrams in the exact application installation guide. Connector view, jumper/switch settings, sensors and supported functions vary by generation and vehicle. The universal 28-way and 90-way wire-in tables do not define this plug-in board's factory header.
Software and installation
Use the correct MEITE / EZ Tune release and the model-specific firmware and base map. The installation guide covers sensor settings, baseline checks, expansion, jumper settings and any vehicle-specific exceptions; a base map still needs calibration and verification on the actual engine. See the ME221 family page for wire-in generation and hardware context.
Sources reviewed 17 November 2026.
Revision 4: Motorsport Electronics ME221 Mazda MX-5 Mk1 1989–1995 plug-inME221 Mazda MX-5 Mk1 1989–1995 plug-in ECU. Manufacturer product image: Motorsport Electronics; used with permission.
ME221 plug-in ECU for Mazda MX-5 Mk1 1989–1995. This application-specific unit replaces the factory ECU electronics while using the vehicle's original harness connector, subject to exact fitment and configuration. Motorsport Electronics product information · application installation guide.
Identification and application
The manufacturer identifies this as its early two-plug NA application. Later Mk1 cars can use a three-plug ECU; check the original connector before selecting the board. Record the serial, board version, firmware, factory ECU part number, engine and transmission before installing. The ME221 and ME442 are separate hardware choices; the manufacturer lists wideband, onboard logging and EGT as ME442 plug-in features. Optional electronic throttle equipment and supported functions vary by board and configuration. See ME's model comparison and downloads.
Connector and pinout
Use the OEM header and auxiliary connector diagrams in the exact application installation guide. Connector view, jumper/switch settings, sensors and supported functions vary by generation and vehicle. The universal 28-way and 90-way wire-in tables do not define this plug-in board's factory header.
OEM header assignments
Documented positions from the manufacturer application guide, looking into the ECU connector from the loom wire side. Positions not shown in that guide are not asserted here. Functions and auxiliary DBW availability depend on model, board revision, hardware and configuration.
Pin
Function in manufacturer guide
1B
Ignition 12 V
1C
Fuel pump (early)
1D
LS4 spare / LS4
1E
CEL / LS11
1F
Alternative tachometer output; see appendix C
1G
Ignition 1 & 4 / COIL 1
1H
Ignition 2 & 3 / COIL 2
1i
DBW motor − (auxiliary; ME442 optional DBW)
1J
Air-con relay / LS15
1K
EGT K-type + / EGT1
1L
Primary fan relay, 1.8 engines / LS12
1M
VSS speed / DIGIN 4
1N
VTPS 5 V reference via VTPS DIP switch
1Q
Air-con switch / DIGIN 5
1R
Primary fan relay, 1.6 engines / LS13
1V
Clutch switch / DIGIN 6
2A/B/C/D
Grounds
2E
CAS sensor signal / VR_CRANK
2G
CAS sensor signal / VR_CAMA
2i
12 V output for four-pin coil-pack-driven tacho
2K
5 V reference
2L
TPS signal / ANA V2
2M
>94 TPS signal
2N
O2 sensor signal / ANA V3
2O
Airflow signal / ANA V4
2P
Inlet air temperature / ANA T1
2Q
Coolant sensor / ANA T2
2S
Air-con blower relay (1995) / LS16
2R
DBW +
2T
Fuel pump relay (1993+) / LS14
2U
Injector 1 (& 3 before 1993)
2V
Injector 2 (& 4 before 1993)
2W
PWM idle valve / LS9
2X
Purge / boost solenoid / LS10
2Y
Injector 3
2Z
Injector 4
MAP
On-board MAP sensor / ANA V1
Auxiliary connector assignments
The ME GEN2 installation guide lists this 20-way Molex Mini-Fit Jr connector. Check the original diagram for orientation, the actual model and fitted options: the table describes the documented connector, not a guarantee every function is supported on every ME221 or ME442 core.
Pin
Function in manufacturer guide
1
Injector 5 — 3.5 A FB protected
2
Injector 6 — 3.5 A FB protected
3
Injector 7 — 3.5 A FB protected
4
Injector 8 — 3.5 A FB protected
5
Coil 3 — 50 mA TTL
6
Coil 4 — 50 mA TTL
7
LS1 — 2 A PWM-capable
8
LS2 — 2 A PWM-capable
9
LS3 — 2 A PWM-capable
10
Knock signal
11
DI 1 — 1 kΩ 5 V pull-up
12
DI 2 — 1 kΩ 5 V pull-up
13
DI 3 — 1 kΩ 5 V pull-up
14
Analogue volt 5 — 0–5 V
15
Analogue volt 6 — 0–5 V
16
Analogue volt 7 — 0–5 V
17
CAN 1 low — 120 Ω terminated
18
CAN 1 high — 120 Ω terminated
19
5 V reference — 100 mA max
20
Knock and sensor ground
The guide asks users to contact ME for EGT connection on this 1989–95 application.
Motorsport Electronics does not publish the microcontroller part number. A distributor specification sheet for the ME221 lists a 120 MHz 32-bit RISC processor; this is a vendor specification rather than a component identification. ATP Turbo ME221 specification sheet (May 2023), accessed 19 November 2026.
Software and installation
Use the correct MEITE / EZ Tune release and the model-specific firmware and base map. The installation guide covers sensor settings, baseline checks, expansion, jumper settings and any vehicle-specific exceptions; a base map still needs calibration and verification on the actual engine. See the ME221 family page for wire-in generation and hardware context.