Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
Motorsport Electronics ME442
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Changes from revision 1 to revision 3

Removed text is struck through; added text is highlighted.

ME442 Mazda MX-5 Mk2.5 2001–2005 plug-in ECU. Manufacturer product image: Motorsport Electronics; used with permission.

ME442 plug-in ECU for Mazda MX-5 Mk2.5 2001–2005. This application-specific unit replaces the factory ECU electronics while using the vehicle's original harness connector, subject to exact fitment and configuration. Motorsport Electronics product information · application installation guide.

Identification and application

The guide covers the NBFL/late Mk2.5 plug-in, distinct from the 1999–2000 NB board. Confirm the OE harness, cam-trigger and VVT configuration against the manual. Record the serial, board version, firmware, factory ECU part number, engine and transmission before installing. The ME221 and ME442 are separate hardware choices; the manufacturer lists wideband, onboard logging and EGT as ME442 plug-in features. Optional electronic throttle equipment and supported functions vary by board and configuration. See ME's model comparison and downloads.

Connector and pinout

Use the OEM header and auxiliary connector diagrams in the exact application installation guide. Connector view, jumper/switch settings, sensors and supported functions vary by generation and vehicle. The universal 28-way and 90-way wire-in tables do not define this plug-in board's factory header.

OEM header assignmentsDocumented positions from the manufacturer application guide, looking into the ECU connector from the loom wire side. Positions not shown in that guide are not asserted here. Functions and auxiliary DBW availability depend on model, board revision, hardware and configuration.PinFunction in manufacturer guide2AInjector 12BCooling fan relay / LS152CAir-con fan relay / LS162DInjector 22GInjector 32JInjector 42KAir-con clutch relay / LS142M/2OFuel pump relay / LS112NVICS solenoid / LS172P/4D/4S12 V ignition2QIdle valve / LS102RCEL / LS133A/BGrounds3CPurge solenoid / LS53FIgnition 1 & 4 / coil 13HMain relay / LS183iIgnition 2 & 3 / coil 23MAlternator control; see baseboard sticker if present3OTachometer3TSpeed sensor / DIGIN 43UBattery light / LS123VCamshaft sensor / VR_CAMA3YCrank sensor / VR_CRANK4FAir-con switch / DIGIN 54iClutch switch / DIGIN 64KDBW motor +, optional ME442 DBW only4L5 V reference4MKnock sensor / KNOCK 14NInlet-air temperature / ANA T14OKnock sensor ground4PCoolant sensor / ANA T24RVVT solenoid / LS94UDBW motor −, optional ME442 DBW only4VThrottle signal / ANA V24WO2 signal / ANA V34XMAF signal / ANA V4MAPOn-board MAP / ANA V1Auxiliary connector assignmentsThe ME GEN2 installation guide lists this 20-way Molex Mini-Fit Jr connector. Check the original diagram for orientation, the actual model and fitted options: the table describes the documented connector, not a guarantee every function is supported on every ME221 or ME442 core.PinFunction in manufacturer guide1Injector 5 — 3.5 A FB protected2Injector 6 — 3.5 A FB protected3Injector 7 — 3.5 A FB protected4Injector 8 — 3.5 A FB protected5Coil 3 — 50 mA TTL6Coil 4 — 50 mA TTL7LS1 — 2 A PWM-capable8LS2 — 2 A PWM-capable9LS3 — 2 A PWM-capable10K-type EGT signal — ME442 only11DI 1 — 1 kΩ 5 V pull-up12DI 2 — 1 kΩ 5 V pull-up13DI 3 — 1 kΩ 5 V pull-up14Analogue volt 5 — 0–5 V15Analogue volt 6 — 0–5 V16Analogue volt 7 — 0–5 V17CAN 1 low18CAN 1 high195 V reference — 50 mA max20EGT and sensor ground

Software and installation

Use the correct MEITE / EZ Tune release and the model-specific firmware and base map. The installation guide covers sensor settings, baseline checks, expansion, jumper settings and any vehicle-specific exceptions; a base map still needs calibration and verification on the actual engine. See the ME442 family page for wire-in generation and hardware context.

Sources reviewed 17 November 2026.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 1: Motorsport Electronics ME442 Mazda MX-5 Mk2.5 2001–2005 plug-in

ME442 plug-in ECU for Mazda MX-5 Mk2.5 2001–2005. This application-specific unit replaces the factory ECU electronics while using the vehicle's original harness connector, subject to exact fitment and configuration. Motorsport Electronics product information · application installation guide.

Identification and application

The guide covers the NBFL/late Mk2.5 plug-in, distinct from the 1999–2000 NB board. Confirm the OE harness, cam-trigger and VVT configuration against the manual. Record the serial, board version, firmware, factory ECU part number, engine and transmission before installing. The ME221 and ME442 are separate hardware choices; the manufacturer lists wideband, onboard logging and EGT as ME442 plug-in features. Optional electronic throttle equipment and supported functions vary by board and configuration. See ME's model comparison and downloads.

Connector and pinout

Use the OEM header and auxiliary connector diagrams in the exact application installation guide. Connector view, jumper/switch settings, sensors and supported functions vary by generation and vehicle. The universal 28-way and 90-way wire-in tables do not define this plug-in board's factory header.

Software and installation

Use the correct MEITE / EZ Tune release and the model-specific firmware and base map. The installation guide covers sensor settings, baseline checks, expansion, jumper settings and any vehicle-specific exceptions; a base map still needs calibration and verification on the actual engine. See the ME442 family page for wire-in generation and hardware context.

Sources reviewed 17 November 2026.

Revision 3: Motorsport Electronics ME442 Mazda MX-5 Mk2.5 2001–2005 plug-in
ME442 Mazda MX-5 Mk2.5 2001-2005 plug-in ECU
ME442 Mazda MX-5 Mk2.5 2001–2005 plug-in ECU. Manufacturer product image: Motorsport Electronics; used with permission.

ME442 plug-in ECU for Mazda MX-5 Mk2.5 2001–2005. This application-specific unit replaces the factory ECU electronics while using the vehicle's original harness connector, subject to exact fitment and configuration. Motorsport Electronics product information · application installation guide.

Identification and application

The guide covers the NBFL/late Mk2.5 plug-in, distinct from the 1999–2000 NB board. Confirm the OE harness, cam-trigger and VVT configuration against the manual. Record the serial, board version, firmware, factory ECU part number, engine and transmission before installing. The ME221 and ME442 are separate hardware choices; the manufacturer lists wideband, onboard logging and EGT as ME442 plug-in features. Optional electronic throttle equipment and supported functions vary by board and configuration. See ME's model comparison and downloads.

Connector and pinout

Use the OEM header and auxiliary connector diagrams in the exact application installation guide. Connector view, jumper/switch settings, sensors and supported functions vary by generation and vehicle. The universal 28-way and 90-way wire-in tables do not define this plug-in board's factory header.

OEM header assignments

Documented positions from the manufacturer application guide, looking into the ECU connector from the loom wire side. Positions not shown in that guide are not asserted here. Functions and auxiliary DBW availability depend on model, board revision, hardware and configuration.

PinFunction in manufacturer guide
2AInjector 1
2BCooling fan relay / LS15
2CAir-con fan relay / LS16
2DInjector 2
2GInjector 3
2JInjector 4
2KAir-con clutch relay / LS14
2M/2OFuel pump relay / LS11
2NVICS solenoid / LS17
2P/4D/4S12 V ignition
2QIdle valve / LS10
2RCEL / LS13
3A/BGrounds
3CPurge solenoid / LS5
3FIgnition 1 & 4 / coil 1
3HMain relay / LS18
3iIgnition 2 & 3 / coil 2
3MAlternator control; see baseboard sticker if present
3OTachometer
3TSpeed sensor / DIGIN 4
3UBattery light / LS12
3VCamshaft sensor / VR_CAMA
3YCrank sensor / VR_CRANK
4FAir-con switch / DIGIN 5
4iClutch switch / DIGIN 6
4KDBW motor +, optional ME442 DBW only
4L5 V reference
4MKnock sensor / KNOCK 1
4NInlet-air temperature / ANA T1
4OKnock sensor ground
4PCoolant sensor / ANA T2
4RVVT solenoid / LS9
4UDBW motor −, optional ME442 DBW only
4VThrottle signal / ANA V2
4WO2 signal / ANA V3
4XMAF signal / ANA V4
MAPOn-board MAP / ANA V1

Auxiliary connector assignments

The ME GEN2 installation guide lists this 20-way Molex Mini-Fit Jr connector. Check the original diagram for orientation, the actual model and fitted options: the table describes the documented connector, not a guarantee every function is supported on every ME221 or ME442 core.

PinFunction in manufacturer guide
1Injector 5 — 3.5 A FB protected
2Injector 6 — 3.5 A FB protected
3Injector 7 — 3.5 A FB protected
4Injector 8 — 3.5 A FB protected
5Coil 3 — 50 mA TTL
6Coil 4 — 50 mA TTL
7LS1 — 2 A PWM-capable
8LS2 — 2 A PWM-capable
9LS3 — 2 A PWM-capable
10K-type EGT signal — ME442 only
11DI 1 — 1 kΩ 5 V pull-up
12DI 2 — 1 kΩ 5 V pull-up
13DI 3 — 1 kΩ 5 V pull-up
14Analogue volt 5 — 0–5 V
15Analogue volt 6 — 0–5 V
16Analogue volt 7 — 0–5 V
17CAN 1 low
18CAN 1 high
195 V reference — 50 mA max
20EGT and sensor ground

Software and installation

Use the correct MEITE / EZ Tune release and the model-specific firmware and base map. The installation guide covers sensor settings, baseline checks, expansion, jumper settings and any vehicle-specific exceptions; a base map still needs calibration and verification on the actual engine. See the ME442 family page for wire-in generation and hardware context.

Sources reviewed 17 November 2026.