Removed text is struck through; added text is highlighted.
ME221 Toyota Starlet EP82 plug-in ECU. Manufacturer product image: Motorsport Electronics; used with permission.
ME221 plug-in ECU for Toyota Starlet EP82. This application-specific unit replaces the factory ECU electronics while using the vehicle's original harness connector, subject to exact fitment and configuration. Motorsport Electronics product information · application installation guide.
Identification and application
ME supplies a dedicated EP82 plug-in. Its GEN2 installation guide covers EP82 and EP91, but board, original connector and base-map choices still need to be matched. Record the serial, board version, firmware, factory ECU part number, engine and transmission before installing. The ME221 and ME442 are separate hardware choices; the manufacturer lists wideband, onboard logging and EGT as ME442 plug-in features. Optional electronic throttle equipment and supported functions vary by board and configuration. See ME's model comparison and downloads.
Connector and pinout
Use the OEM header and auxiliary connector diagrams in the exact application installation guide. Connector view, jumper/switch settings, sensors and supported functions vary by generation and vehicle. The universal 28-way and 90-way wire-in tables do not define this plug-in board's factory header.
Auxiliary connector assignmentsThe ME GEN2 installation guide lists this 20-way Molex Mini-Fit Jr connector. Check the original diagram for orientation, the actual model and fitted options: the table describes the documented connector, not a guarantee every function is supported on every ME221 or ME442 core.PinFunction in manufacturer guide1Injector 5 — 3.5 A FB protected2Injector 6 — 3.5 A FB protected3Injector 7 — 3.5 A FB protected4Injector 8 — 3.5 A FB protected5NC6NC7LS1 — 2 A PWM-capable8LS2 — 2 A PWM-capable9LS3 — 2 A PWM-capable10K-type EGT signal — ME442 only11DI 1 — 1 kΩ 5 V pull-up12DI 2 — 1 kΩ 5 V pull-up13DI 3 not available — boost button14Analogue volt 5 — 0–5 V15Analogue volt 6 — 0–5 V16Analogue volt 7 — 0–5 V17CAN 1 low — unterminated18CAN 1 high — unterminated195 V reference — 100 mA max20EGT and sensor groundThe guide states that the connector orientation differs between EP82 and EP91; follow the appropriate original diagram. EGT is marked for ME442 versions.ProcessorMotorsport Electronics does not publish the microcontroller part number. A distributor specification sheet for the ME221 lists a 120 MHz 32-bit RISC processor; this is a vendor specification rather than a component identification. ATP Turbo ME221 specification sheet (May 2023), accessed 19 November 2026.Structured connector pinoutEvery cavity of the EP82 and EP91 factory headers and the 20-way auxiliary connector, with the manufacturer's assignments, is drawn in Motorsport Electronics ME221 and ME442 EP82/EP91 plug-in connector pinout.
Software and installation
Use the correct MEITE / EZ Tune release and the model-specific firmware and base map. The installation guide covers sensor settings, baseline checks, expansion, jumper settings and any vehicle-specific exceptions; a base map still needs calibration and verification on the actual engine. See the ME221 family page for wire-in generation and hardware context.
Sources reviewed 17 November 2026.
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 1: Motorsport Electronics ME221 Toyota Starlet EP82 plug-in
ME supplies a dedicated EP82 plug-in. Its GEN2 installation guide covers EP82 and EP91, but board, original connector and base-map choices still need to be matched. Record the serial, board version, firmware, factory ECU part number, engine and transmission before installing. The ME221 and ME442 are separate hardware choices; the manufacturer lists wideband, onboard logging and EGT as ME442 plug-in features. Optional electronic throttle equipment and supported functions vary by board and configuration. See ME's model comparison and downloads.
Connector and pinout
Use the OEM header and auxiliary connector diagrams in the exact application installation guide. Connector view, jumper/switch settings, sensors and supported functions vary by generation and vehicle. The universal 28-way and 90-way wire-in tables do not define this plug-in board's factory header.
Software and installation
Use the correct MEITE / EZ Tune release and the model-specific firmware and base map. The installation guide covers sensor settings, baseline checks, expansion, jumper settings and any vehicle-specific exceptions; a base map still needs calibration and verification on the actual engine. See the ME221 family page for wire-in generation and hardware context.
Sources reviewed 17 November 2026.
Revision 4: Motorsport Electronics ME221 Toyota Starlet EP82 plug-inME221 Toyota Starlet EP82 plug-in ECU. Manufacturer product image: Motorsport Electronics; used with permission.
ME supplies a dedicated EP82 plug-in. Its GEN2 installation guide covers EP82 and EP91, but board, original connector and base-map choices still need to be matched. Record the serial, board version, firmware, factory ECU part number, engine and transmission before installing. The ME221 and ME442 are separate hardware choices; the manufacturer lists wideband, onboard logging and EGT as ME442 plug-in features. Optional electronic throttle equipment and supported functions vary by board and configuration. See ME's model comparison and downloads.
Connector and pinout
Use the OEM header and auxiliary connector diagrams in the exact application installation guide. Connector view, jumper/switch settings, sensors and supported functions vary by generation and vehicle. The universal 28-way and 90-way wire-in tables do not define this plug-in board's factory header.
Auxiliary connector assignments
The ME GEN2 installation guide lists this 20-way Molex Mini-Fit Jr connector. Check the original diagram for orientation, the actual model and fitted options: the table describes the documented connector, not a guarantee every function is supported on every ME221 or ME442 core.
Pin
Function in manufacturer guide
1
Injector 5 — 3.5 A FB protected
2
Injector 6 — 3.5 A FB protected
3
Injector 7 — 3.5 A FB protected
4
Injector 8 — 3.5 A FB protected
5
NC
6
NC
7
LS1 — 2 A PWM-capable
8
LS2 — 2 A PWM-capable
9
LS3 — 2 A PWM-capable
10
K-type EGT signal — ME442 only
11
DI 1 — 1 kΩ 5 V pull-up
12
DI 2 — 1 kΩ 5 V pull-up
13
DI 3 not available — boost button
14
Analogue volt 5 — 0–5 V
15
Analogue volt 6 — 0–5 V
16
Analogue volt 7 — 0–5 V
17
CAN 1 low — unterminated
18
CAN 1 high — unterminated
19
5 V reference — 100 mA max
20
EGT and sensor ground
The guide states that the connector orientation differs between EP82 and EP91; follow the appropriate original diagram. EGT is marked for ME442 versions.
Processor
Motorsport Electronics does not publish the microcontroller part number. A distributor specification sheet for the ME221 lists a 120 MHz 32-bit RISC processor; this is a vendor specification rather than a component identification. ATP Turbo ME221 specification sheet (May 2023), accessed 19 November 2026.
Use the correct MEITE / EZ Tune release and the model-specific firmware and base map. The installation guide covers sensor settings, baseline checks, expansion, jumper settings and any vehicle-specific exceptions; a base map still needs calibration and verification on the actual engine. See the ME221 family page for wire-in generation and hardware context.