Page organisation in this revision
- Page type
- Reference hub
- Subject
- Engine ECU
- Parent
- MegaSquirt and MS3Pro standalone ECUs
- Applies to
- No ECU-specific applicability
- Tool groups
- None
- Manufacturers
- None
Changes from revision 1 to revision 3
Removed text is struck through; added text is highlighted.
Earlier MicroSquirt V2; DIYAutoTune lists it as a legacy unsupported ECU. Do not use V3 or MS3Pro Mini connector assignments without matching documentation. DIYAutoTune product and support information.
Identification and wiring
Record exact model, board revision, firmware, installation and carrier before wiring. DIYAutoTune documentation index includes model-specific manuals; connector functions are not interchangeable across ECU and module designs. Confirm all power, grounds and driver ratings from the applicable manual.
See MegaSquirt and MS3Pro family. Sources reviewed 17 November 2026.
35-way AMPSEAL connectorFunctions below follow the MicroSquirt V2 wiring guide. The earlier pre-V3 guide labels pin 21 as ground; V3 assigns this pin to VR2−. Older units and harnesses may be modified, so confirm revision and actual wiring with the manufacturer. See its connector view, electrical limits and related input guidance before wiring; supported assignments can depend on firmware and hardware modifications.PinFunction in guide112 Volt Supply2CAN High3CAN Low4VRIN2+5Spare Input6Flex Fuel7FIDLE8FUEL PUMP9INJECTOR 110INJECTOR 211IGNITION OUTPUT #212IGNITION OUTPUT #113SERIAL Rx14SERIAL Tx15BOOTLOADER16ACCEL LED17WARM-UP LED18N/C (ground)19SERIAL GROUND20SENSOR GROUND21GROUND22GROUND23GROUND24MAP25CLT26IAT27TPS28Vref29SPARE ADC30OPTOIN+31OPTOIN-32VRIN1+33VRIN-34O235TACH OUTPUTStructured pinoutThis V2 pin list is tabulated alongside the manufacturer-documented MicroSquirt V3 assignments, and redrawn as a pin index, in MicroSquirt V3 and V2 AMPSEAL connector pinout; the V2 entries are graded suspected there because they come from the earlier wiring guide rather than a current manufacturer manual.
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 1: MicroSquirt V2
Earlier MicroSquirt V2; DIYAutoTune lists it as a legacy unsupported ECU. Do not use V3 or MS3Pro Mini connector assignments without matching documentation. DIYAutoTune product and support information.
Identification and wiring
Record exact model, board revision, firmware, installation and carrier before wiring. DIYAutoTune documentation index includes model-specific manuals; connector functions are not interchangeable across ECU and module designs. Confirm all power, grounds and driver ratings from the applicable manual.
See MegaSquirt and MS3Pro family. Sources reviewed 17 November 2026.
Revision 3: MicroSquirt V2
Earlier MicroSquirt V2; DIYAutoTune lists it as a legacy unsupported ECU. Do not use V3 or MS3Pro Mini connector assignments without matching documentation. DIYAutoTune product and support information.
Identification and wiring
Record exact model, board revision, firmware, installation and carrier before wiring. DIYAutoTune documentation index includes model-specific manuals; connector functions are not interchangeable across ECU and module designs. Confirm all power, grounds and driver ratings from the applicable manual.
See MegaSquirt and MS3Pro family. Sources reviewed 17 November 2026.
35-way AMPSEAL connector
Functions below follow the MicroSquirt V2 wiring guide. The earlier pre-V3 guide labels pin 21 as ground; V3 assigns this pin to VR2−. Older units and harnesses may be modified, so confirm revision and actual wiring with the manufacturer. See its connector view, electrical limits and related input guidance before wiring; supported assignments can depend on firmware and hardware modifications.
| Pin | Function in guide |
|---|
| 1 | 12 Volt Supply |
| 2 | CAN High |
| 3 | CAN Low |
| 4 | VRIN2+ |
| 5 | Spare Input |
| 6 | Flex Fuel |
| 7 | FIDLE |
| 8 | FUEL PUMP |
| 9 | INJECTOR 1 |
| 10 | INJECTOR 2 |
| 11 | IGNITION OUTPUT #2 |
| 12 | IGNITION OUTPUT #1 |
| 13 | SERIAL Rx |
| 14 | SERIAL Tx |
| 15 | BOOTLOADER |
| 16 | ACCEL LED |
| 17 | WARM-UP LED |
| 18 | N/C (ground) |
| 19 | SERIAL GROUND |
| 20 | SENSOR GROUND |
| 21 | GROUND |
| 22 | GROUND |
| 23 | GROUND |
| 24 | MAP |
| 25 | CLT |
| 26 | IAT |
| 27 | TPS |
| 28 | Vref |
| 29 | SPARE ADC |
| 30 | OPTOIN+ |
| 31 | OPTOIN- |
| 32 | VRIN1+ |
| 33 | VRIN- |
| 34 | O2 |
| 35 | TACH OUTPUT |
Structured pinout
This V2 pin list is tabulated alongside the manufacturer-documented MicroSquirt V3 assignments, and redrawn as a pin index, in MicroSquirt V3 and V2 AMPSEAL connector pinout; the V2 entries are graded suspected there because they come from the earlier wiring guide rather than a current manufacturer manual.