Removed text is struck through; added text is highlighted.
Emtron sl8 product image: Emtron Australia. Reproduced with permission.
Emtron SL8 is a programmable standalone ECU from Emtron Australia. Eight sequential injector and ignition channels are listed, with two 34-way connectors, Ethernet communication, two knock inputs and up to 32 MB logging. Emtron SL8 datasheet.
Identification and configuration
Record the ECU model, serial, board revision and loaded firmware. The Emtune calibration determines the use of configurable inputs and outputs; electrical limits, ignition driver type, injector impedance and wired supplies must be checked for the actual unit. Emtron engine-management manual.
Connector pinouts
These tables reproduce the positions in Emtron's SL8 pinout. The source diagrams are viewed looking into the ECU connector. NC is the manufacturer's unconnected designation. Verify connector keying, revision, power, grounds and all limits in the original before wiring; assignments differ between models and hardware revisions.
Sensor 0 V references and main ECU grounds have distinct wiring requirements. H-bridge supplies and relay control require the installation described in the manufacturer's power-distribution guide. See Emtron wiring index and revision-specific diagrams.
Documentation and setup
Manufacturer's SL8 datasheet and product illustrationModel-specific pinout and connector diagramsEmtune setup and technical manualEmtron family reference
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 2: Emtron SL8Emtron sl8 product image: Emtron Australia. Reproduced with permission.
Emtron SL8 is a programmable standalone ECU from Emtron Australia. Eight sequential injector and ignition channels are listed, with two 34-way connectors, Ethernet communication, two knock inputs and up to 32 MB logging. Emtron SL8 datasheet.
Identification and configuration
Record the ECU model, serial, board revision and loaded firmware. The Emtune calibration determines the use of configurable inputs and outputs; electrical limits, ignition driver type, injector impedance and wired supplies must be checked for the actual unit. Emtron engine-management manual.
Connector pinouts
These tables reproduce the positions in Emtron's SL8 pinout. The source diagrams are viewed looking into the ECU connector. NC is the manufacturer's unconnected designation. Verify connector keying, revision, power, grounds and all limits in the original before wiring; assignments differ between models and hardware revisions.
Connector A
Pin
Channel Name
Pin
Channel Name
A1
Injection Channel 1
A18
Auxiliary Output 9
A2
Injection Channel 2
A19
Auxiliary Output 10
A3
Injection Channel 3
A20
Digital Input 1
A4
Injection Channel 4
A21
Digital Input 2
A5
Injection Channel 5
A22
Digital Input 3
A6
Injection Channel 6
A23
Digital Input 4
A7
Injection Channel 7
A24
Digital Input 5
A8
Injection Channel 8
A25
Digital Input 6
A9
Sensor Supply 8V
A26
Ignition Channel 1
A10
Auxiliary Output 1
A27
Ignition Channel 2
A11
Auxiliary Output 2
A28
Ignition Channel 3
A12
Auxiliary Output 3
A29
Ignition Channel 4
A13
Auxiliary Output 4
A30
Ignition Channel 5
A14
Auxiliary Output 5
A31
Ignition Channel 6
A15
Auxiliary Output 6
A32
Ignition Channel 7
A16
Auxiliary Output 7
A33
Ignition Channel 8
A17
Auxiliary Output 8
A34
Auxiliary Output 9-10, 14V Supply
Connector B
Pin
Channel Name
Pin
Channel Name
B1
ECU 14V Supply
B18
ECU Ground
B2
Sensor Supply Vref1: 5.0V
B19
Analog Input Channel 6
B3
EFI Relay Output (Low Side 200mA)
B20
Analog Input Channel 7
B4
Ignition Switch Input
B21
Analog Input Channel 8
B5
Crank Index Sensor +
B22
Analog Input Channel 9
B6
Crank Index Sensor -
B23
Analog Input Channel 10
B7
Sync Sensor +
B24
Knock 2 +
B8
Sync Sensor -
B25
Knock 2 -
B9
Shield (Crank/Sync/ Knock)
B26
ECU Ground
B10
Analog Sensor 0V Reference
B27
CAN 1H
B11
Analog Input Channel 1
B28
CAN 1L
B12
Analog Input Channel 2
B29
NC
B13
Analog Input Channel 3
B30
NC
B14
Analog Input Channel 4
B31
Ethernet Tx +
B15
Analog Input Channel 5
B32
Ethernet Tx -
B16
Knock 1 +
B33
Ethernet Rx +
B17
Knock 1 -
B34
Ethernet Rx -
Sensor 0 V references and main ECU grounds have distinct wiring requirements. H-bridge supplies and relay control require the installation described in the manufacturer's power-distribution guide. See Emtron wiring index and revision-specific diagrams.
Revision 2: Emtron SL8Emtron sl8 product image: Emtron Australia. Reproduced with permission.
Emtron SL8 is a programmable standalone ECU from Emtron Australia. Eight sequential injector and ignition channels are listed, with two 34-way connectors, Ethernet communication, two knock inputs and up to 32 MB logging. Emtron SL8 datasheet.
Identification and configuration
Record the ECU model, serial, board revision and loaded firmware. The Emtune calibration determines the use of configurable inputs and outputs; electrical limits, ignition driver type, injector impedance and wired supplies must be checked for the actual unit. Emtron engine-management manual.
Connector pinouts
These tables reproduce the positions in Emtron's SL8 pinout. The source diagrams are viewed looking into the ECU connector. NC is the manufacturer's unconnected designation. Verify connector keying, revision, power, grounds and all limits in the original before wiring; assignments differ between models and hardware revisions.
Connector A
Pin
Channel Name
Pin
Channel Name
A1
Injection Channel 1
A18
Auxiliary Output 9
A2
Injection Channel 2
A19
Auxiliary Output 10
A3
Injection Channel 3
A20
Digital Input 1
A4
Injection Channel 4
A21
Digital Input 2
A5
Injection Channel 5
A22
Digital Input 3
A6
Injection Channel 6
A23
Digital Input 4
A7
Injection Channel 7
A24
Digital Input 5
A8
Injection Channel 8
A25
Digital Input 6
A9
Sensor Supply 8V
A26
Ignition Channel 1
A10
Auxiliary Output 1
A27
Ignition Channel 2
A11
Auxiliary Output 2
A28
Ignition Channel 3
A12
Auxiliary Output 3
A29
Ignition Channel 4
A13
Auxiliary Output 4
A30
Ignition Channel 5
A14
Auxiliary Output 5
A31
Ignition Channel 6
A15
Auxiliary Output 6
A32
Ignition Channel 7
A16
Auxiliary Output 7
A33
Ignition Channel 8
A17
Auxiliary Output 8
A34
Auxiliary Output 9-10, 14V Supply
Connector B
Pin
Channel Name
Pin
Channel Name
B1
ECU 14V Supply
B18
ECU Ground
B2
Sensor Supply Vref1: 5.0V
B19
Analog Input Channel 6
B3
EFI Relay Output (Low Side 200mA)
B20
Analog Input Channel 7
B4
Ignition Switch Input
B21
Analog Input Channel 8
B5
Crank Index Sensor +
B22
Analog Input Channel 9
B6
Crank Index Sensor -
B23
Analog Input Channel 10
B7
Sync Sensor +
B24
Knock 2 +
B8
Sync Sensor -
B25
Knock 2 -
B9
Shield (Crank/Sync/ Knock)
B26
ECU Ground
B10
Analog Sensor 0V Reference
B27
CAN 1H
B11
Analog Input Channel 1
B28
CAN 1L
B12
Analog Input Channel 2
B29
NC
B13
Analog Input Channel 3
B30
NC
B14
Analog Input Channel 4
B31
Ethernet Tx +
B15
Analog Input Channel 5
B32
Ethernet Tx -
B16
Knock 1 +
B33
Ethernet Rx +
B17
Knock 1 -
B34
Ethernet Rx -
Sensor 0 V references and main ECU grounds have distinct wiring requirements. H-bridge supplies and relay control require the installation described in the manufacturer's power-distribution guide. See Emtron wiring index and revision-specific diagrams.