Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
Motorsport Electronics standalone ECUs
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Changes from revision 1 to revision 1

Removed text is struck through; added text is highlighted.

NODIZ Pro GEN-X product. Image: Motorsport Electronics; used with permission.

NODIZ Pro GEN-X is a four-cylinder programmable ignition-only controller for distributorless, wasted-spark applications, including carburetted engines. ME describes crank-triggered ignition with direct coil drive, configurable auxiliary outputs and optional load input. The related ME100 GEN-X adds functions, including the closed-loop VVT mode documented in the shared manual. Manufacturer documentation · ME manuals and downloads.

Identification and configuration

Record the complete model label, serial number, hardware generation, firmware and harness. Wire-in ECUs and vehicle-specific plug-in versions have different physical connections. Software and output assignments depend on the unit and calibration; follow the appropriate manufacturer wiring guide and check the installed configuration.

GEN-X 24-way pinout — manual revision 1.3

From NODIZ Pro / ME100 GEN-X manual revision 1.3, section 6.2. The source depicts the plug face and numbers; check the view, exact hardware and equipment-specific notes. It describes the four-cylinder configuration; the current ME100 listing advertises additional cylinder support, which this older table alone does not establish. Do not use it to wire an unverified variant.

PinDocumented functionA1Coil B switched groundA2Inlet air temperatureA3Chassis groundA4RS232 transmitA5RS232 receiveA6Sensor / signal groundA7TPS / MAP 5 V referenceA8Coil C; not used in documented four-cylinder configurationB1Coil A switched groundB2Coolant temperatureB3Launch control inputB4Knock positiveB5Crank sensor positiveB6Crank sensor negativeB7Sensor shields / grounds and serial groundB8Coil D; not used in documented four-cylinder configurationC1Low side 2C2Low side 1C3TPS / MAP signalC4Cam VR positiveC5Cam VR negativeC6Ignition-switched 12 VC7Low side 3C8Tachometer output

Software and further information

ME provides MEITE / EZ Tune, firmware and installation guides on its support page. Confirm the software and firmware required by the actual unit. See Motorsport Electronics ECU family.

Sources reviewed 17 November 2026.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 1: Motorsport Electronics NODIZ Pro GEN-X
NODIZ Pro GEN-X product
NODIZ Pro GEN-X product. Image: Motorsport Electronics; used with permission.

NODIZ Pro GEN-X is a four-cylinder programmable ignition-only controller for distributorless, wasted-spark applications, including carburetted engines. ME describes crank-triggered ignition with direct coil drive, configurable auxiliary outputs and optional load input. The related ME100 GEN-X adds functions, including the closed-loop VVT mode documented in the shared manual. Manufacturer documentation · ME manuals and downloads.

Identification and configuration

Record the complete model label, serial number, hardware generation, firmware and harness. Wire-in ECUs and vehicle-specific plug-in versions have different physical connections. Software and output assignments depend on the unit and calibration; follow the appropriate manufacturer wiring guide and check the installed configuration.

GEN-X 24-way pinout — manual revision 1.3

From NODIZ Pro / ME100 GEN-X manual revision 1.3, section 6.2. The source depicts the plug face and numbers; check the view, exact hardware and equipment-specific notes. It describes the four-cylinder configuration; the current ME100 listing advertises additional cylinder support, which this older table alone does not establish. Do not use it to wire an unverified variant.

PinDocumented function
A1Coil B switched ground
A2Inlet air temperature
A3Chassis ground
A4RS232 transmit
A5RS232 receive
A6Sensor / signal ground
A7TPS / MAP 5 V reference
A8Coil C; not used in documented four-cylinder configuration
B1Coil A switched ground
B2Coolant temperature
B3Launch control input
B4Knock positive
B5Crank sensor positive
B6Crank sensor negative
B7Sensor shields / grounds and serial ground
B8Coil D; not used in documented four-cylinder configuration
C1Low side 2
C2Low side 1
C3TPS / MAP signal
C4Cam VR positive
C5Cam VR negative
C6Ignition-switched 12 V
C7Low side 3
C8Tachometer output

Software and further information

ME provides MEITE / EZ Tune, firmware and installation guides on its support page. Confirm the software and firmware required by the actual unit. See Motorsport Electronics ECU family.

Sources reviewed 17 November 2026.

Revision 1: Motorsport Electronics NODIZ Pro GEN-X
NODIZ Pro GEN-X product
NODIZ Pro GEN-X product. Image: Motorsport Electronics; used with permission.

NODIZ Pro GEN-X is a four-cylinder programmable ignition-only controller for distributorless, wasted-spark applications, including carburetted engines. ME describes crank-triggered ignition with direct coil drive, configurable auxiliary outputs and optional load input. The related ME100 GEN-X adds functions, including the closed-loop VVT mode documented in the shared manual. Manufacturer documentation · ME manuals and downloads.

Identification and configuration

Record the complete model label, serial number, hardware generation, firmware and harness. Wire-in ECUs and vehicle-specific plug-in versions have different physical connections. Software and output assignments depend on the unit and calibration; follow the appropriate manufacturer wiring guide and check the installed configuration.

GEN-X 24-way pinout — manual revision 1.3

From NODIZ Pro / ME100 GEN-X manual revision 1.3, section 6.2. The source depicts the plug face and numbers; check the view, exact hardware and equipment-specific notes. It describes the four-cylinder configuration; the current ME100 listing advertises additional cylinder support, which this older table alone does not establish. Do not use it to wire an unverified variant.

PinDocumented function
A1Coil B switched ground
A2Inlet air temperature
A3Chassis ground
A4RS232 transmit
A5RS232 receive
A6Sensor / signal ground
A7TPS / MAP 5 V reference
A8Coil C; not used in documented four-cylinder configuration
B1Coil A switched ground
B2Coolant temperature
B3Launch control input
B4Knock positive
B5Crank sensor positive
B6Crank sensor negative
B7Sensor shields / grounds and serial ground
B8Coil D; not used in documented four-cylinder configuration
C1Low side 2
C2Low side 1
C3TPS / MAP signal
C4Cam VR positive
C5Cam VR negative
C6Ignition-switched 12 V
C7Low side 3
C8Tachometer output

Software and further information

ME provides MEITE / EZ Tune, firmware and installation guides on its support page. Confirm the software and firmware required by the actual unit. See Motorsport Electronics ECU family.

Sources reviewed 17 November 2026.