Removed text is struck through; added text is highlighted.
AEM Infinity ECU family illustration, showing multiple models; not necessarily Infinity 708. Image: AEM / Holley, reproduced with permission.
AEM Infinity 708 (manufacturer part 30-7101) is a programmable Infinity engine-management ECU, a separately identified model in AEM's hardware comparison.
Identification and capability
Manufacturer specificationInfinity 708Maximum cylinders, as listed8Sequential injector outputs8 high- or low-impedanceIgnition8 logic-levelConnector positions129Electronic throttleDualCAN channels2Internal wideband channels2
Compare injector impedance and ignition driver type before connecting components. Maximum cylinder count does not imply every feature or configuration is available simultaneously; verify exact part number, harness and calibration. AEM lists InfinityTuner software separately from Series 1/2 EMS software.
ProcessorAEM and Holley marketing text describes the Infinity family as built around a 32-bit floating-point, 200 MHz automotive processor rated at 400 MIPS, running a real-time operating system, with a separate power-management processor behind the permanent battery power inputs. These are vendor claims; the silicon vendor and part number are not named in AEM's hardware specification or in the trade-press and retailer pages checked, so the MCU family is not established.Engine applicationsThe Infinity 708 is a universal standalone ECU for engines of up to eight cylinders. AEM's Series 7 hardware specification includes example system schematics for a 1995 BMW E36 M3, Mitsubishi Lancer Evolution VIII and IX, a 1993-1998 Toyota Supra 2JZ-GTE and a GM LS3 drive-by-wire installation (manufacturer documentation). Engine codes beyond those named are not given.
Connector and wiring
AEM's Infinity 708 family hardware and wiring reference gives electrical limits and connector diagrams. Match the ECU's number and physical harness, and verify connector orientation. The 506 and 508 share an 80-way shell but some pin assignments differ; Series 3 and Series 7 use different connectors and are not interchangeable by name.
Connector pinoutThe 129 positions are split between a 73-pin C1 and a 56-pin C2 connector. The full assignment (manufacturer documentation) is on the AEM Infinity 708, 710 and 712 connector pinout page. The source gives no connector face view, so the diagrams are numbered pin indexes. Diagram redrawn by Tuning Wiki from the AEM Series 7 hardware specification.
Further documents
Manufacturer wiring and hardware specificationsAEM Infinity user manual and comparisonAEM engine management support and application harnessesAEM manufacturer index
Sources reviewed 17 November 2026. Availability of an exact part or application should be checked separately.
AEM formerly called this Infinity-8; it listed part numbers 30-7101, 30-7109 and 30-7110. AEM model-name change announcement.
SourcesInfinity Hardware Specification 30-7100/7101/7111. AEM manufacturer document, build 13 April 2017. Accessed 19 November 2026.AEM Performance Electronics Infinity Series 7 ECU. Trade press repeating AEM's processor description. Accessed 19 November 2026.
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 2: AEM Infinity 708AEM Infinity ECU family illustration, showing multiple models; not necessarily Infinity 708. Image: AEM / Holley, reproduced with permission.
AEM Infinity 708 (manufacturer part 30-7101) is a programmable Infinity engine-management ECU, a separately identified model in AEM's hardware comparison.
Identification and capability
Manufacturer specification
Infinity 708
Maximum cylinders, as listed
8
Sequential injector outputs
8 high- or low-impedance
Ignition
8 logic-level
Connector positions
129
Electronic throttle
Dual
CAN channels
2
Internal wideband channels
2
Compare injector impedance and ignition driver type before connecting components. Maximum cylinder count does not imply every feature or configuration is available simultaneously; verify exact part number, harness and calibration. AEM lists InfinityTuner software separately from Series 1/2 EMS software.
Connector and wiring
AEM's Infinity 708 family hardware and wiring reference gives electrical limits and connector diagrams. Match the ECU's number and physical harness, and verify connector orientation. The 506 and 508 share an 80-way shell but some pin assignments differ; Series 3 and Series 7 use different connectors and are not interchangeable by name.
Revision 3: AEM Infinity 708AEM Infinity ECU family illustration, showing multiple models; not necessarily Infinity 708. Image: AEM / Holley, reproduced with permission.
AEM Infinity 708 (manufacturer part 30-7101) is a programmable Infinity engine-management ECU, a separately identified model in AEM's hardware comparison.
Identification and capability
Manufacturer specification
Infinity 708
Maximum cylinders, as listed
8
Sequential injector outputs
8 high- or low-impedance
Ignition
8 logic-level
Connector positions
129
Electronic throttle
Dual
CAN channels
2
Internal wideband channels
2
Compare injector impedance and ignition driver type before connecting components. Maximum cylinder count does not imply every feature or configuration is available simultaneously; verify exact part number, harness and calibration. AEM lists InfinityTuner software separately from Series 1/2 EMS software.
Processor
AEM and Holley marketing text describes the Infinity family as built around a 32-bit floating-point, 200 MHz automotive processor rated at 400 MIPS, running a real-time operating system, with a separate power-management processor behind the permanent battery power inputs. These are vendor claims; the silicon vendor and part number are not named in AEM's hardware specification or in the trade-press and retailer pages checked, so the MCU family is not established.
Engine applications
The Infinity 708 is a universal standalone ECU for engines of up to eight cylinders. AEM's Series 7 hardware specification includes example system schematics for a 1995 BMW E36 M3, Mitsubishi Lancer Evolution VIII and IX, a 1993-1998 Toyota Supra 2JZ-GTE and a GM LS3 drive-by-wire installation (manufacturer documentation). Engine codes beyond those named are not given.
Connector and wiring
AEM's Infinity 708 family hardware and wiring reference gives electrical limits and connector diagrams. Match the ECU's number and physical harness, and verify connector orientation. The 506 and 508 share an 80-way shell but some pin assignments differ; Series 3 and Series 7 use different connectors and are not interchangeable by name.
Connector pinout
The 129 positions are split between a 73-pin C1 and a 56-pin C2 connector. The full assignment (manufacturer documentation) is on the AEM Infinity 708, 710 and 712 connector pinout page. The source gives no connector face view, so the diagrams are numbered pin indexes. Diagram redrawn by Tuning Wiki from the AEM Series 7 hardware specification.