Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
MegaSquirt and MS3Pro standalone ECUs
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Changes from revision 2 to revision 3

Removed text is struck through; added text is highlighted.

MS3Pro Mini. Image: manufacturer product page; permission to republish confirmed by the user.

MS3Pro Mini is a MegaSquirt-family engine-management product. Compact 35-way AMPSEAL ECU with eight saturated injector outputs, four logic-level ignition outputs, built-in 4-bar MAP and separate barometric sensor, according to its manual. Model source.

Identification and software

Record the ECU label, processor generation, board revision, firmware and installed hardware modifications. Calibration software and firmware must match the hardware. DIYAutoTune software and firmware · Model-specific information.

Wiring and pinout

MS3Pro Mini AMPSEAL connector

Positions below follow the manufacturer connector decal and Mini manual. Verify physical orientation against the manufacturer drawing and note that MicroSquirt uses a different assignment despite the similar connector. Output H can be used as a tachometer with the documented pull-up configuration.

PinFunction112 V switched input2+5 V VREF output3PWM output 1 / idle4Fuel pump output5Injector A6Injector B7Injector C8Injector D9Injector E10Injector F11Injector G12Injector H13Analogue input 114Analogue input 215Analogue input 316Analogue input 417Spark output A18Spark output B19Spark output C20Spark output D21Sensor ground22Power ground23Power ground24CAN low25CAN high26Coolant temperature input27Intake air temperature input28Throttle position input29Digital switched input 1 / flex fuel30Crank sensor +31Crank sensor −32Cam sensor +33Cam sensor −34Digital frequency input 135Digital frequency input 2

Use the matching model document and wiring or support reference; the manufacturer manual index distinguishes wire-in and vehicle-specific variants. Check connector orientation, wiring changes, fuse ratings and output configuration before connecting loads; matching cases or software families do not establish identical pin functions.

See the MegaSquirt and MS3Pro family guide. Sources reviewed 17 November 2026.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 2: MS3Pro Mini

MS3Pro Mini is a MegaSquirt-family engine-management product. Compact 35-way AMPSEAL ECU with eight saturated injector outputs, four logic-level ignition outputs, built-in 4-bar MAP and separate barometric sensor, according to its manual. Model source.

Identification and software

Record the ECU label, processor generation, board revision, firmware and installed hardware modifications. Calibration software and firmware must match the hardware. DIYAutoTune software and firmware · Model-specific information.

Wiring and pinout

MS3Pro Mini AMPSEAL connector

Positions below follow the manufacturer connector decal and Mini manual. Verify physical orientation against the manufacturer drawing and note that MicroSquirt uses a different assignment despite the similar connector. Output H can be used as a tachometer with the documented pull-up configuration.

PinFunction
112 V switched input
2+5 V VREF output
3PWM output 1 / idle
4Fuel pump output
5Injector A
6Injector B
7Injector C
8Injector D
9Injector E
10Injector F
11Injector G
12Injector H
13Analogue input 1
14Analogue input 2
15Analogue input 3
16Analogue input 4
17Spark output A
18Spark output B
19Spark output C
20Spark output D
21Sensor ground
22Power ground
23Power ground
24CAN low
25CAN high
26Coolant temperature input
27Intake air temperature input
28Throttle position input
29Digital switched input 1 / flex fuel
30Crank sensor +
31Crank sensor −
32Cam sensor +
33Cam sensor −
34Digital frequency input 1
35Digital frequency input 2

Use the matching model document and wiring or support reference; the manufacturer manual index distinguishes wire-in and vehicle-specific variants. Check connector orientation, wiring changes, fuse ratings and output configuration before connecting loads; matching cases or software families do not establish identical pin functions.

See the MegaSquirt and MS3Pro family guide. Sources reviewed 17 November 2026.

Revision 3: MS3Pro Mini
MS3Pro Mini ECU
MS3Pro Mini. Image: manufacturer product page; permission to republish confirmed by the user.

MS3Pro Mini is a MegaSquirt-family engine-management product. Compact 35-way AMPSEAL ECU with eight saturated injector outputs, four logic-level ignition outputs, built-in 4-bar MAP and separate barometric sensor, according to its manual. Model source.

Identification and software

Record the ECU label, processor generation, board revision, firmware and installed hardware modifications. Calibration software and firmware must match the hardware. DIYAutoTune software and firmware · Model-specific information.

Wiring and pinout

MS3Pro Mini AMPSEAL connector

Positions below follow the manufacturer connector decal and Mini manual. Verify physical orientation against the manufacturer drawing and note that MicroSquirt uses a different assignment despite the similar connector. Output H can be used as a tachometer with the documented pull-up configuration.

PinFunction
112 V switched input
2+5 V VREF output
3PWM output 1 / idle
4Fuel pump output
5Injector A
6Injector B
7Injector C
8Injector D
9Injector E
10Injector F
11Injector G
12Injector H
13Analogue input 1
14Analogue input 2
15Analogue input 3
16Analogue input 4
17Spark output A
18Spark output B
19Spark output C
20Spark output D
21Sensor ground
22Power ground
23Power ground
24CAN low
25CAN high
26Coolant temperature input
27Intake air temperature input
28Throttle position input
29Digital switched input 1 / flex fuel
30Crank sensor +
31Crank sensor −
32Cam sensor +
33Cam sensor −
34Digital frequency input 1
35Digital frequency input 2

Use the matching model document and wiring or support reference; the manufacturer manual index distinguishes wire-in and vehicle-specific variants. Check connector orientation, wiring changes, fuse ratings and output configuration before connecting loads; matching cases or software families do not establish identical pin functions.

See the MegaSquirt and MS3Pro family guide. Sources reviewed 17 November 2026.