Removed text is struck through; added text is highlighted.
Emtron shadow-8 product image: Emtron Australia. Reproduced with permission.
Emtron Shadow 8 is a programmable standalone ECU from Emtron Australia. Eight high-impedance port-injector and eight ignition channels, ten analogue inputs, twelve auxiliary outputs, two CAN buses, two knock inputs and USB-C are listed. One electronic-throttle motor is supported. Emtron Shadow 8 datasheet.
Identification and configuration
Record the ECU model, serial, board revision and loaded firmware. The Emtune calibration determines the use of configurable inputs and outputs; electrical limits, ignition driver type, injector impedance and wired supplies must be checked for the actual unit. Emtron engine-management manual.
Connector pinouts
These tables reproduce the positions in Emtron's Shadow 8 pinout. The source diagrams are viewed looking into the ECU connector. NC is the manufacturer's unconnected designation. Verify connector keying, revision, power, grounds and all limits in the original before wiring; assignments differ between models and hardware revisions.
Connector A
PinChannel NamePinChannel NameA1ECU SupplyA18Analog Voltage 6A2Sensor 8.0V Sensor SupplyA19Analog Voltage 7A3Sensor 5.0V Sensor SupplyA20Analog Voltage 8A40V Analog ReferenceA21Analog Voltage 9A5Crank Position SensorA22Analog Voltage 10A6Sync Position SensorA23CAN Bus 1 LowA7Trigger GroundA24Knock 2 +veA8ShieldA25Knock 2 -veA9Ground 1A26Digital Input 1A10Analog Voltage 1A27Digital Input 2A11Analog Voltage 2A28Digital Input 3A12Analog Voltage 3A29Digital Input 4A13Analog Voltage 4A30Digital Input 5A14Analog Voltage 5A31Digital Input 6A15CAN Bus 1 HighA32CAN Bus 2 HighA16Knock 1 +veA33CAN Bus 2 LowA17Knock 1 -veA34Ground 2
Sensor 0 V references and main ECU grounds have distinct wiring requirements. H-bridge supplies and relay control require the installation described in the manufacturer's power-distribution guide. See Emtron wiring index and revision-specific diagrams.
Documentation and setup
Manufacturer's Shadow 8 datasheet and product illustrationModel-specific pinout and connector diagramsEmtune setup and technical manualEmtron family reference
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 1: Emtron Shadow 8
Emtron Shadow 8 is a programmable standalone ECU from Emtron Australia. Eight high-impedance port-injector and eight ignition channels, ten analogue inputs, twelve auxiliary outputs, two CAN buses, two knock inputs and USB-C are listed. One electronic-throttle motor is supported. Emtron Shadow 8 datasheet.
Identification and configuration
Record the ECU model, serial, board revision and loaded firmware. The Emtune calibration determines the use of configurable inputs and outputs; electrical limits, ignition driver type, injector impedance and wired supplies must be checked for the actual unit. Emtron engine-management manual.
Connector pinouts
These tables reproduce the positions in Emtron's Shadow 8 pinout. The source diagrams are viewed looking into the ECU connector. NC is the manufacturer's unconnected designation. Verify connector keying, revision, power, grounds and all limits in the original before wiring; assignments differ between models and hardware revisions.
Connector A
Pin
Channel Name
Pin
Channel Name
A1
ECU Supply
A18
Analog Voltage 6
A2
Sensor 8.0V Sensor Supply
A19
Analog Voltage 7
A3
Sensor 5.0V Sensor Supply
A20
Analog Voltage 8
A4
0V Analog Reference
A21
Analog Voltage 9
A5
Crank Position Sensor
A22
Analog Voltage 10
A6
Sync Position Sensor
A23
CAN Bus 1 Low
A7
Trigger Ground
A24
Knock 2 +ve
A8
Shield
A25
Knock 2 -ve
A9
Ground 1
A26
Digital Input 1
A10
Analog Voltage 1
A27
Digital Input 2
A11
Analog Voltage 2
A28
Digital Input 3
A12
Analog Voltage 3
A29
Digital Input 4
A13
Analog Voltage 4
A30
Digital Input 5
A14
Analog Voltage 5
A31
Digital Input 6
A15
CAN Bus 1 High
A32
CAN Bus 2 High
A16
Knock 1 +ve
A33
CAN Bus 2 Low
A17
Knock 1 -ve
A34
Ground 2
Connector B
Pin
Channel Name
Pin
Channel Name
B1
Battery Constant (HOT) Supply
B18
Digital Input 7
B2
Injector Cylinder 1
B19
Digital Input 8
B3
Injector Cylinder 2
B20
Digital Input 9
B4
Injector Cylinder 3
B21
Digital Input 10 / Ignition Switch
B5
Injector Cylinder 4
B22
Aux Output 9
B6
Injector Cylinder 5
B23
Aux Output 10
B7
Injector Cylinder 6
B24
Aux Output 11
B8
Injector Cylinder 7
B25
Aux Output 12
B9
Injector Cylinder 8
B26
Aux 9-12 Power Supply
B10
Aux Output 1
B27
Ignition TTL Cylinder 1
B11
Aux Output 2
B28
Ignition TTL Cylinder 2
B12
Aux Output 3
B29
Ignition TTL Cylinder 3
B13
Aux Output 4
B30
Ignition TTL Cylinder 4
B14
Aux Output 5
B31
Ignition TTL Cylinder 5
B15
Aux Output 6
B32
Ignition TTL Cylinder 6
B16
Aux Output 7
B33
Ignition TTL Cylinder 7
B17
Aux Output 8
B34
Ignition TTL Cylinder 8
Sensor 0 V references and main ECU grounds have distinct wiring requirements. H-bridge supplies and relay control require the installation described in the manufacturer's power-distribution guide. See Emtron wiring index and revision-specific diagrams.
Revision 2: Emtron Shadow 8Emtron shadow-8 product image: Emtron Australia. Reproduced with permission.
Emtron Shadow 8 is a programmable standalone ECU from Emtron Australia. Eight high-impedance port-injector and eight ignition channels, ten analogue inputs, twelve auxiliary outputs, two CAN buses, two knock inputs and USB-C are listed. One electronic-throttle motor is supported. Emtron Shadow 8 datasheet.
Identification and configuration
Record the ECU model, serial, board revision and loaded firmware. The Emtune calibration determines the use of configurable inputs and outputs; electrical limits, ignition driver type, injector impedance and wired supplies must be checked for the actual unit. Emtron engine-management manual.
Connector pinouts
These tables reproduce the positions in Emtron's Shadow 8 pinout. The source diagrams are viewed looking into the ECU connector. NC is the manufacturer's unconnected designation. Verify connector keying, revision, power, grounds and all limits in the original before wiring; assignments differ between models and hardware revisions.
Connector A
Pin
Channel Name
Pin
Channel Name
A1
ECU Supply
A18
Analog Voltage 6
A2
Sensor 8.0V Sensor Supply
A19
Analog Voltage 7
A3
Sensor 5.0V Sensor Supply
A20
Analog Voltage 8
A4
0V Analog Reference
A21
Analog Voltage 9
A5
Crank Position Sensor
A22
Analog Voltage 10
A6
Sync Position Sensor
A23
CAN Bus 1 Low
A7
Trigger Ground
A24
Knock 2 +ve
A8
Shield
A25
Knock 2 -ve
A9
Ground 1
A26
Digital Input 1
A10
Analog Voltage 1
A27
Digital Input 2
A11
Analog Voltage 2
A28
Digital Input 3
A12
Analog Voltage 3
A29
Digital Input 4
A13
Analog Voltage 4
A30
Digital Input 5
A14
Analog Voltage 5
A31
Digital Input 6
A15
CAN Bus 1 High
A32
CAN Bus 2 High
A16
Knock 1 +ve
A33
CAN Bus 2 Low
A17
Knock 1 -ve
A34
Ground 2
Connector B
Pin
Channel Name
Pin
Channel Name
B1
Battery Constant (HOT) Supply
B18
Digital Input 7
B2
Injector Cylinder 1
B19
Digital Input 8
B3
Injector Cylinder 2
B20
Digital Input 9
B4
Injector Cylinder 3
B21
Digital Input 10 / Ignition Switch
B5
Injector Cylinder 4
B22
Aux Output 9
B6
Injector Cylinder 5
B23
Aux Output 10
B7
Injector Cylinder 6
B24
Aux Output 11
B8
Injector Cylinder 7
B25
Aux Output 12
B9
Injector Cylinder 8
B26
Aux 9-12 Power Supply
B10
Aux Output 1
B27
Ignition TTL Cylinder 1
B11
Aux Output 2
B28
Ignition TTL Cylinder 2
B12
Aux Output 3
B29
Ignition TTL Cylinder 3
B13
Aux Output 4
B30
Ignition TTL Cylinder 4
B14
Aux Output 5
B31
Ignition TTL Cylinder 5
B15
Aux Output 6
B32
Ignition TTL Cylinder 6
B16
Aux Output 7
B33
Ignition TTL Cylinder 7
B17
Aux Output 8
B34
Ignition TTL Cylinder 8
Sensor 0 V references and main ECU grounds have distinct wiring requirements. H-bridge supplies and relay control require the installation described in the manufacturer's power-distribution guide. See Emtron wiring index and revision-specific diagrams.