Emtron KV16M is a programmable standalone ECU from Emtron Australia. Sixteen fuel and twelve sequential ignition channels are listed. The KV16M has a 136-way Deutsch Autosport connector system, distinct from the Superseal KV16. Emtron KV16M datasheet.
Identification and configuration
Record the ECU model, serial, board revision and loaded firmware. The Emtune calibration determines the use of configurable inputs and outputs; electrical limits, ignition driver type, injector impedance and wired supplies must be checked for the actual unit. Emtron engine-management manual.
Connector pinouts
These tables reproduce the positions in Emtron's KV16M pinout. The source diagrams are viewed looking into the ECU connector. NC is the manufacturer's unconnected designation. Verify connector keying, revision, power, grounds and all limits in the original before wiring; assignments differ between models and hardware revisions.
Connector A
| Pin | Channel Name | Pin | Channel Name |
|---|---|---|---|
| 1 | Injection Channel 1 | 29 | Lambda 2 Heater + |
| 2 | Injection Channel 2 | 30 | Lambda 2 Heater - |
| 3 | Injection Channel 3 | 31 | Digital Input Ground Out |
| 4 | Injection Channel 4 | 32 | Ignition Channel 1 |
| 5 | Injection Channel 5 | 33 | Ignition Channel 2 |
| 6 | Injection Channel 6 | 34 | Ignition Channel 3 |
| 7 | Injection Channel 7 | 35 | Ignition Channel 4 |
| 8 | Injection Channel 8 | 36 | Ignition Channel 5 |
| 9 | Injection Channel 9 | 37 | Ignition Channel 6 |
| 10 | Injection Channel 10 | 38 | Ignition Channel 7 |
| 11 | Injection Channel 11 | 39 | Ignition Channel 8 |
| 12 | Injection Channel 12 | 40 | Ignition Channel 9 |
| 13 | Injection Channel 13 | 41 | Ignition Channel 10 |
| 14 | Injection Channel 14 | 42 | Ignition Channel 11 |
| 15 | Injection Channel 15 | 43 | Ignition Channel 12 |
| 16 | Injection Channel 16 | 44 | Digital Input 3 |
| 17 | Lambda 1 Nernst Cell (Vs) | 45 | Digital Input 2 |
| 18 | Lambda 1 Cal Resistor (CalR) | 46 | Digital Input 1 |
| 19 | Lambda 1 Pump Cell (Ip) | 47 | Digital Input 9 |
| 20 | Lambda 1 Virtual Ground (VGnd) | 48 | Digital Input 8 |
| 21 | Lambda 1 Heater + | 49 | Digital Input 7 |
| 22 | Lambda 1 Heater - | 50 | Digital Input 6 |
| 23 | Digital Input 13 | 51 | Digital Input 5 |
| 24 | Digital Input 14 | 52 | Digital Input 4 |
| 25 | Lambda 2 Pump Cell (Ip) | 53 | Digital Input 10 |
| 26 | Lambda 2 Virtual Ground (VGnd) | 54 | Digital Input 11 |
| 27 | Lambda 2 Nernst Cell (Vs) | 55 | Digital Input 12 |
| 28 | Lambda 2 Cal Resistor (CalR) |
Connector B
| Pin | Channel Name |
|---|---|
| A | ECU 14V Supply |
| B | ECU 14V Supply |
| C | ECU 14V Supply |
| D | ECU Ground |
| E | ECU Ground |
| F | Auxiliary Output 16 |
| G | Auxiliary Output 15 |
| H | Auxiliary Output 14 |
| J | Auxiliary Output 12 |
| K | Auxiliary Output 10 |
| L | Auxiliary Output 8 |
| M | Auxiliary Output 7 |
| N | Auxiliary Output 5 |
| P | Auxiliary Output 3 |
| R | Auxiliary Output 1 |
| S | Auxiliary Output 2 |
| T | ECU 14V Supply |
| U | ECU Ground |
| V | ECU Ground |
| W | Auxiliary Output 13 |
| X | Auxiliary Output 11 |
| Y | Auxiliary Output 9 |
| Z | Auxiliary Output 6 |
| a | Auxiliary Output 4 |
| b | ECU Ground |
| c | ECU Ground |
Connector C
| Pin | Channel Name | Pin | Channel Name |
|---|---|---|---|
| 1 | Analog Input Channel 1 | 29 | Analog Sensor 0V Reference |
| 2 | Analog Input Channel 2 | 30 | Analog Sensor 0V Reference |
| 3 | Analog Input Channel 3 | 31 | Analog Sensor 0V Reference |
| 4 | Analog Input Channel 4 | 32 | Knock 2 + |
| 5 | Analog Input Channel 5 | 33 | Analog Out |
| 6 | Analog Input Channel 6 | 34 | CAN 2L |
| 7 | Analog Input Channel 7 | 35 | CAN 2H |
| 8 | Analog Input Channel 8 | 36 | CAN 1L |
| 9 | Analog Input Channel 9 | 37 | CAN 1H |
| 10 | Analog Input Channel 10 | 38 | Sensor Supply Vref2: 5.0V |
| 11 | Analog Input Channel 11 | 39 | Sensor Supply Vref2: 5.0V |
| 12 | Analog Input Channel 12 | 40 | Knock 1 - |
| 13 | Analog Input Channel 13 | 41 | Sync Sensor - |
| 14 | Analog Input Channel 14 | 42 | Sync Sensor + |
| 15 | Analog Input Channel 15 | 43 | Crank Index Sensor - |
| 16 | Analog Input Channel 16 | 44 | Crank Index Sensor + |
| 17 | Analog Input Channel 17 | 45 | Sensor Supply Vref1: 5.0V |
| 18 | Analog Input Channel 18 | 46 | Sensor Supply Vref1: 5.0V |
| 19 | Analog Input Channel 19 | 47 | Knock 1 + |
| 20 | Analog Input Channel 20 | 48 | Ethernet Tx + |
| 21 | Analog Input Channel 21 | 49 | Ethernet Tx - |
| 22 | Analog Input Channel 22 | 50 | Ethernet Rx + |
| 23 | Analog Input Channel 23 | 51 | Ethernet Rx - |
| 24 | Analog Input Channel 24 | 52 | Sensor Supply 8V |
| 25 | Knock 2 - | 53 | Constant 14V Supply(Backup) |
| 26 | SHIELD (Crank/Cam/ Knock) | 54 | Sensor Supply Vref3: 5.0V |
| 27 | SHIELD (Crank/Cam/ Knock) | 55 | Sensor Supply Vref3: 5.0V |
| 28 | Analog Sensor 0V Reference |
Sensor 0 V references and main ECU grounds have distinct wiring requirements. H-bridge supplies and relay control require the installation described in the manufacturer's power-distribution guide. See Emtron wiring index and revision-specific diagrams.