Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
Holley EFI standalone ECUs
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Holley EFI Dominator is a programmable US Holley engine-control unit; ECU part number 554-114 is listed by Holley. Holley ECU and harness parts guide · manufacturer comparison.

Identification and capabilities

The Dominator has six ECU connectors, two wideband channels, USB PC communication, internal/external logging and substantially expanded inputs and outputs. It can control supported drive-by-wire and automatic-transmission installations with the correct hardware, harness and software.

HardwareManufacturer description
ECU identifier554-114
Injector drivers12 injector drivers with high- and low-impedance support
Model-specific distinctionJ1A/J1B are only the common main connectors. Additional Dominator connectors require the exact Dominator wiring and function allocation; never infer their pins from HP or Terminator.

Injector impedance, timing hardware, firmware, sensor types and output allocation determine compatibility. Kits may use a model ECU with different vehicle-specific main and injector harnesses.

J1A and J1B ECU pinouts

Holley's ECU pinout gives J1A and J1B for HP, Dominator, Terminator X and X Max; this table records the Dominator interpretation. Source naming and ratings are preserved; verify connector orientation and model-specific harness, fuse and configuration before connection.

Connector J1A

PositionFunction
A1Coil negative input
A2Fuel pump output +12 V (10 A maximum)
A3Input 2 (capabilities depend on model)
A4Input 4 (capabilities depend on model)
A5TPS input
A6Points trigger output
A7Wideband 1 COMPR2
A8Wideband 1 shield
A9Wideband heater negative
A10Switched +12 V input
A11Manifold air temperature input
A12Input 1 (capabilities depend on model)
A13Input 3 (capabilities depend on model)
A14Cam/crank ground
A15Gauge digital output
A16Wideband 1 COMPR1
A17Wideband 1 VS−/IP+
A18Sensor ground
A19Engine coolant temperature input
A20Oil pressure input
A21Knock 2 input
A22Cam sync input / ignition bypass output
A23MAP sensor input
A24CAN low
A25Wideband 1 VS+
A26Sensor +5 V
A27Not used
A28EST/Spout output
A29Knock 1 input
A30Crank speed input
A31Fuel pressure input
A32CAN high
A33Wideband 1 IP+
A34Wideband heater positive

Connector J1B

PositionFunction
B1IAC A low
B2IAC A high
B3Output 4 (ground/PWM−)
B4Injector F
B5Injector G
B6Injector H
B7Injector E
B8IAC B low
B9IAC B high
B10Output 3 (ground/PWM−)
B11Output 2 (high-side / PWM+)
B12Output 1 (high-side / PWM+)
B13Injector D
B14EST ground output
B15EST 2 (cylinder 2)
B16EST 4 (cylinder 4)
B17EST 6 (cylinder 6)
B18EST 8 (cylinder 8)
B19Injector A
B20EST 12 V output
B21EST 1 (cylinder 1)
B22EST 3 (cylinder 3)
B23EST 5 (cylinder 5)
B24EST 7 (cylinder 7)
B25Injector C
B26Injector B

Input type codes and B11/B12 drive polarity vary across the families; refer to Holley's auxiliary I/O harness guide. Additional connectors are not represented by this table.

Software and sources

Source review: 17 November 2026.