
Pro-8 is the smaller ECU in the EMU Pro range, aimed at up to eight-cylinder engines. ECUMaster lists eight peak-and-hold injector outputs, eight software-selectable active or passive ignition outputs, 12 low-side auxiliary outputs, three full H-bridges, two LSU 4.9 controllers, two drive-by-wire controllers, two CAN buses and one LIN bus. The IP65 enclosure measures 165 × 95 × 38 mm. Direct-injection engines need the separate GDI Driver. Manufacturer product specification · Manufacturer comparison.
Connector pinout and wiring
The linked v1.0 pinout specifies three Superseal 1.0 mating housings A 4-1437290-1, B 1473416-1 and C 4-1437290-0. CAN1 serves PC communications and requires external termination; USB is for a flash logging drive. Use the exact PDF drawings for cavity numbers, orientation and current limits. Exact-model manufacturer pinout.
Software and installation
Record the ECU serial, firmware, software and project versions and confirm assigned outputs and trigger inputs before connecting loads. The manufacturer downloads contain current software, manuals and supported base maps. Base maps do not establish the correct pinout for a particular vehicle. Compare with the ECUMaster family guide.
Connector pin tables
The tables transcribe ECUMaster Pro-8 pinout v1.0. Use the numbered manufacturer connector drawings and mating-housing keys to establish orientation; these tables describe ECU connector positions, not sensor-side terminal numbers. Configurable and shared functions depend on software setup. Refer to the source for protection, currents, grounds, termination and sensor-wiring conditions before use.
Connector A
| Pin | Manufacturer function |
|---|---|
| A1 | Ignition 8 |
| A2 | Injector 1 |
| A3 | Injector 2 |
| A4 | Injector 3 |
| A5 | Injector 4 |
| A6 | Injector 5 |
| A7 | Injector 6 |
| A8 | Injector 7 |
| A9 | Injector 8 |
| A10 | Ignition 7 |
| A11 | Power ground |
| A12 | +5 V source A |
| A13 | Digital 2 |
| A14 | Digital 4 |
| A15 | Digital 8 |
| A16 | Digital 6 (turboshaft) |
| A17 | Power ground |
| A18 | Ignition 6 |
| A19 | Power ground |
| A20 | Digital ground |
| A21 | Digital 1 (crank) |
| A22 | Digital 3 |
| A23 | Digital 7 |
| A24 | Digital 5 (turboshaft) |
| A25 | Auxiliary 9 |
| A26 | Ignition 5 |
| A27 | Ignition 4 |
| A28 | Ignition 3 |
| A29 | Ignition 2 |
| A30 | Ignition 1 |
| A31 | CAN 1 high (PC) |
| A32 | CAN 1 low (PC) |
| A33 | CAN 2 high |
| A34 | CAN 2 low |
Connector B
| Pin | Manufacturer function |
|---|---|
| B1 | Auxiliary 1 (wideband heater option) |
| B2 | Auxiliary 2 (wideband heater option) |
| B3 | Auxiliary 3 (wideband heater option) |
| B4 | Auxiliary 4 (wideband heater option) |
| B5 | Auxiliary 5 |
| B6 | Auxiliary 6 |
| B7 | Auxiliary 7 |
| B8 | +12 V supply |
| B9 | Digital ground (flash drive) |
| B10 | USB D− (flash drive) |
| B11 | USB D+ (flash drive) |
| B12 | +5 V source A (flash drive) |
| B13 | Auxiliary 8 |
| B14 | +12 V supply |
| B15 | +12 V switched |
| B16 | Knock sensor 1 |
| B17 | Knock sensor 2 |
| B18 | Wideband 2 VGND (LSU 4.9) |
| B19 | Power ground |
| B20 | Wideband 1 Ip (LSU 4.9) |
| B21 | Wideband 1 Vs (LSU 4.9) |
| B22 | Wideband 1 Rcal (LSU 4.9) |
| B23 | Wideband 1 VGND (LSU 4.9) |
| B24 | Wideband 2 Ip (LSU 4.9) |
| B25 | Wideband 2 Vs (LSU 4.9) |
| B26 | Wideband 2 Rcal (LSU 4.9) |
Connector C
| Pin | Manufacturer function |
|---|---|
| C1 | Auxiliary 10 |
| C2 | Auxiliary 11 |
| C3 | Auxiliary 12 |
| C4 | Analogue 7 |
| C5 | Analogue 10 (2.2 kΩ pull) |
| C6 | H-bridge 1A |
| C7 | H-bridge 2B |
| C8 | H-bridge 3A |
| C9 | H-bridge 2A |
| C10 | Analogue 1 (MAP) |
| C11 | Analogue 3 |
| C12 | Analogue 5 |
| C13 | Analogue 8 |
| C14 | Analogue 11 (2.2 kΩ pull) |
| C15 | Analogue 13 (1 kΩ pull) |
| C16 | Analogue 15 (330 Ω pull) |
| C17 | H-bridge 3B |
| C18 | Analogue 2 |
| C19 | Analogue 4 |
| C20 | Analogue 6 |
| C21 | Analogue 9 (2.2 kΩ pull) |
| C22 | Analogue 12 (2.2 kΩ pull) |
| C23 | Analogue 14 (1 kΩ pull) |
| C24 | Analogue 16 (100 Ω pull) |
| C25 | H-bridge 1B |
| C26 | LIN |
| C27 | +5 V source B |
| C28 | +5 V source B |
| C29 | Analogue ground |
| C30 | Power ground |
| C31 | Precision analogue 1 |
| C32 | Precision analogue 2 |
| C33 | Precision analogue 3 |
| C34 | Precision analogue 4 |
CAN1 carries PC communications and has no internal terminator in the cited document. B9–B12 are the flash-drive connections; they are not the tuning PC connection. All named power and sensor grounds have the specific wiring requirements described by the manufacturer.