Removed text is struck through; added text is highlighted.
DTAFast S-series range, illustrative family photograph: DTAFast. The image is not a model-specific identification. Permission to republish confirmed by the user.
The DTAFast S80 Pro is an S-series programmable engine-management unit. Eight injector and eight coil drivers with two cam inputs in the historical DTA feature matrix. The S-series manual describes traction control on S80 Pro and above. DTAFast historical S-series feature matrix.
Hardware and operation
Refer to the manufacturer S80 Pro connector diagrams, sensor options and notes; outputs can be shared by configurable functions. Confirm the complete ECU label and revision; similarly named S-series units are separate records, and S-series capability differs from T-series. Record the number of injectors, coil arrangement, cam triggers and assigned auxiliary outputs before selecting a calibration.
Wiring and pinout
DTAFast S80 connector pinout and wiring gives connector views, supplies, grounds, sensor and actuator examples. Consult the documented firmware and circuit protection conditions; identify connector keyways and view direction before counting pins. A shared input or output can perform only the function assigned to it.
Software and additional references
The DTAFast S-series Pro manual describes DTASwin calibration software, data logging and model-specific settings. DTAFast S60 Pro product sheet provides an example of output and engine configuration limits. See the DTAFast model family for other ECUs.
S80 Pro pinout — manufacturer diagram
Power and sensor plugs are distinct 34-way connectors. The power connector is shown with three keyways, the sensor connector with four; each set of pin numbers begins at 1. DTAFast's S80 Pro wiring diagram is dated 18 November 2014 and specifies firmware V77.00 or later for all illustrated options. Both connector views are drawn from the pin-insertion side. These tables transcribe the functions shown; unlisted pins are not established as unused. Slash-separated labels are alternatives or configuration-dependent functions.
PinDocumented function1Analogue 2 / log switch / TPS 22Undriven wheel speed, Hall effect3Analogue 3 / gear potentiometer4Launch button5Oil pressure6Fuel pressure7Air temperature95 V output10Analogue 1 / traction cut percentage / launch RPM12Crank magnetic13Crank Hall effect14Shift cut / E85 / air-con / shaft speed15ALS / map 2 / lambda switch16Manifold / barometric pressure17Oil temperature19Left or only lambda signal21, 33Sensor ground22Cam magnetic23Cam Hall effect25Water temperature26CAN high28CAN low34Throttle position8Traction on/off switch11Traction wet/dry switch18Right lambda or launch RPM20Right undriven wheel speed245 V output27Aux switch / pit lane speed29Cam 2 Hall effect30Cam 2 magnetic31Left driven wheel speed32Right driven wheel speed
The manufacturer diagram identifies the power connector's coil and injector outputs by firing order, not necessarily cylinder number. Separate crank and cam Hall and magnetic inputs are alternatives: the diagram says to use only one type per sensor. Check the exact model, keying, orientation, calibration and electrical ratings in the original diagram before wiring.
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 3: DTAFast S80 ProDTAFast S-series range, illustrative family photograph: DTAFast. The image is not a model-specific identification. Permission to republish confirmed by the user.
The DTAFast S80 Pro is an S-series programmable engine-management unit. Eight injector and eight coil drivers with two cam inputs in the historical DTA feature matrix. The S-series manual describes traction control on S80 Pro and above. DTAFast historical S-series feature matrix.
Hardware and operation
Refer to the manufacturer S80 Pro connector diagrams, sensor options and notes; outputs can be shared by configurable functions. Confirm the complete ECU label and revision; similarly named S-series units are separate records, and S-series capability differs from T-series. Record the number of injectors, coil arrangement, cam triggers and assigned auxiliary outputs before selecting a calibration.
Wiring and pinout
DTAFast S80 connector pinout and wiring gives connector views, supplies, grounds, sensor and actuator examples. Consult the documented firmware and circuit protection conditions; identify connector keyways and view direction before counting pins. A shared input or output can perform only the function assigned to it.
Power and sensor plugs are distinct 34-way connectors. The power connector is shown with three keyways, the sensor connector with four; each set of pin numbers begins at 1. DTAFast's S80 Pro wiring diagram is dated 18 November 2014 and specifies firmware V77.00 or later for all illustrated options. Both connector views are drawn from the pin-insertion side. These tables transcribe the functions shown; unlisted pins are not established as unused. Slash-separated labels are alternatives or configuration-dependent functions.
Power connections
Pin
Documented function
1
Coil 3
2
Aux 9 / tacho
3
Aux 7 / fuel pump relay
4
Aux 2 / fan relay
5
Aux 1 / cam control
6
Aux 8 / shift light / electric dump valve
7
Turbo pressure valve
8
Idle valve
9
Injector 1
10
Coil 1
11
Coil 5
12
Coil 7
13, 14
Power grounds
15
Injector 6
16
Injector 5
17
Injector 2
18
Coil 2
19
Coil 8
21
Cam 2
23
Injector 8
24
Injector 7
25
Injector 4
26
Coil 4
27
Coil 6
29
Aux 5 (12 V output)
30
Aux 6
31
Fused 12 V supply
32
Aux 4 / ALS / VTEC
33
Aux 3 / VTEC / Bosch 3-pin idle valve fast side
34
Injector 3
Sensor connections
Pin
Documented function
1
Analogue 2 / log switch / TPS 2
2
Undriven wheel speed, Hall effect
3
Analogue 3 / gear potentiometer
4
Launch button
5
Oil pressure
6
Fuel pressure
7
Air temperature
9
5 V output
10
Analogue 1 / traction cut percentage / launch RPM
12
Crank magnetic
13
Crank Hall effect
14
Shift cut / E85 / air-con / shaft speed
15
ALS / map 2 / lambda switch
16
Manifold / barometric pressure
17
Oil temperature
19
Left or only lambda signal
21, 33
Sensor ground
22
Cam magnetic
23
Cam Hall effect
25
Water temperature
26
CAN high
28
CAN low
34
Throttle position
8
Traction on/off switch
11
Traction wet/dry switch
18
Right lambda or launch RPM
20
Right undriven wheel speed
24
5 V output
27
Aux switch / pit lane speed
29
Cam 2 Hall effect
30
Cam 2 magnetic
31
Left driven wheel speed
32
Right driven wheel speed
The manufacturer diagram identifies the power connector's coil and injector outputs by firing order, not necessarily cylinder number. Separate crank and cam Hall and magnetic inputs are alternatives: the diagram says to use only one type per sensor. Check the exact model, keying, orientation, calibration and electrical ratings in the original diagram before wiring.
Revision 3: DTAFast S80 ProDTAFast S-series range, illustrative family photograph: DTAFast. The image is not a model-specific identification. Permission to republish confirmed by the user.
The DTAFast S80 Pro is an S-series programmable engine-management unit. Eight injector and eight coil drivers with two cam inputs in the historical DTA feature matrix. The S-series manual describes traction control on S80 Pro and above. DTAFast historical S-series feature matrix.
Hardware and operation
Refer to the manufacturer S80 Pro connector diagrams, sensor options and notes; outputs can be shared by configurable functions. Confirm the complete ECU label and revision; similarly named S-series units are separate records, and S-series capability differs from T-series. Record the number of injectors, coil arrangement, cam triggers and assigned auxiliary outputs before selecting a calibration.
Wiring and pinout
DTAFast S80 connector pinout and wiring gives connector views, supplies, grounds, sensor and actuator examples. Consult the documented firmware and circuit protection conditions; identify connector keyways and view direction before counting pins. A shared input or output can perform only the function assigned to it.
Power and sensor plugs are distinct 34-way connectors. The power connector is shown with three keyways, the sensor connector with four; each set of pin numbers begins at 1. DTAFast's S80 Pro wiring diagram is dated 18 November 2014 and specifies firmware V77.00 or later for all illustrated options. Both connector views are drawn from the pin-insertion side. These tables transcribe the functions shown; unlisted pins are not established as unused. Slash-separated labels are alternatives or configuration-dependent functions.
Power connections
Pin
Documented function
1
Coil 3
2
Aux 9 / tacho
3
Aux 7 / fuel pump relay
4
Aux 2 / fan relay
5
Aux 1 / cam control
6
Aux 8 / shift light / electric dump valve
7
Turbo pressure valve
8
Idle valve
9
Injector 1
10
Coil 1
11
Coil 5
12
Coil 7
13, 14
Power grounds
15
Injector 6
16
Injector 5
17
Injector 2
18
Coil 2
19
Coil 8
21
Cam 2
23
Injector 8
24
Injector 7
25
Injector 4
26
Coil 4
27
Coil 6
29
Aux 5 (12 V output)
30
Aux 6
31
Fused 12 V supply
32
Aux 4 / ALS / VTEC
33
Aux 3 / VTEC / Bosch 3-pin idle valve fast side
34
Injector 3
Sensor connections
Pin
Documented function
1
Analogue 2 / log switch / TPS 2
2
Undriven wheel speed, Hall effect
3
Analogue 3 / gear potentiometer
4
Launch button
5
Oil pressure
6
Fuel pressure
7
Air temperature
9
5 V output
10
Analogue 1 / traction cut percentage / launch RPM
12
Crank magnetic
13
Crank Hall effect
14
Shift cut / E85 / air-con / shaft speed
15
ALS / map 2 / lambda switch
16
Manifold / barometric pressure
17
Oil temperature
19
Left or only lambda signal
21, 33
Sensor ground
22
Cam magnetic
23
Cam Hall effect
25
Water temperature
26
CAN high
28
CAN low
34
Throttle position
8
Traction on/off switch
11
Traction wet/dry switch
18
Right lambda or launch RPM
20
Right undriven wheel speed
24
5 V output
27
Aux switch / pit lane speed
29
Cam 2 Hall effect
30
Cam 2 magnetic
31
Left driven wheel speed
32
Right driven wheel speed
The manufacturer diagram identifies the power connector's coil and injector outputs by firing order, not necessarily cylinder number. Separate crank and cam Hall and magnetic inputs are alternatives: the diagram says to use only one type per sensor. Check the exact model, keying, orientation, calibration and electrical ratings in the original diagram before wiring.