Removed text is struck through; added text is highlighted.
DTAFast S-series range, illustrative family photograph: DTAFast. The image is not a model-specific identification. Permission to republish confirmed by the user.
The DTAFast S60 Pro is an S-series programmable engine-management unit. Four injector and four coil drivers. The historical manufacturer product sheet describes four-cylinder sequential injection and coil-per-plug ignition, or up to eight cylinders with non-sequential injection and wasted spark; it supports one cam control. DTAFast historical S-series feature matrix.
Hardware and operation
The manufacturer's diagram labels separate power and sensor connectors and says output numbering follows firing order, not cylinder number. A cam sensor is required for sequential operation; the diagram specifies firmware V77.00 or newer for all illustrated options. Confirm the complete ECU label and revision; similarly named S-series units are separate records, and S-series capability differs from T-series. Record the number of injectors, coil arrangement, cam triggers and assigned auxiliary outputs before selecting a calibration.
Wiring and pinout
DTAFast S60 connector pinout and wiring gives connector views, supplies, grounds, sensor and actuator examples. Consult the documented firmware and circuit protection conditions; identify connector keyways and view direction before counting pins. A shared input or output can perform only the function assigned to it.
Software and additional references
The DTAFast S-series Pro manual describes DTASwin calibration software, data logging and model-specific settings. DTAFast S60 Pro product sheet provides an example of output and engine configuration limits. See the DTAFast model family for other ECUs.
S60 Pro pinout — manufacturer diagram
Power and sensor plugs are distinct 34-way connectors. The power connector is shown with three keyways, the sensor connector with four; each set of pin numbers begins at 1. DTAFast's S60 Pro wiring diagram is dated 18 November 2014 and specifies firmware V77.00 or later for all illustrated options. Both connector views are drawn from the pin-insertion side. These tables transcribe the functions shown; unlisted pins are not established as unused. Slash-separated labels are alternatives or configuration-dependent functions.
The manufacturer diagram identifies the power connector's coil and injector outputs by firing order, not necessarily cylinder number. Separate crank and cam Hall and magnetic inputs are alternatives: the diagram says to use only one type per sensor. Check the exact model, keying, orientation, calibration and electrical ratings in the original diagram before wiring.
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 3: DTAFast S60 ProDTAFast S-series range, illustrative family photograph: DTAFast. The image is not a model-specific identification. Permission to republish confirmed by the user.
The DTAFast S60 Pro is an S-series programmable engine-management unit. Four injector and four coil drivers. The historical manufacturer product sheet describes four-cylinder sequential injection and coil-per-plug ignition, or up to eight cylinders with non-sequential injection and wasted spark; it supports one cam control. DTAFast historical S-series feature matrix.
Hardware and operation
The manufacturer's diagram labels separate power and sensor connectors and says output numbering follows firing order, not cylinder number. A cam sensor is required for sequential operation; the diagram specifies firmware V77.00 or newer for all illustrated options. Confirm the complete ECU label and revision; similarly named S-series units are separate records, and S-series capability differs from T-series. Record the number of injectors, coil arrangement, cam triggers and assigned auxiliary outputs before selecting a calibration.
Wiring and pinout
DTAFast S60 connector pinout and wiring gives connector views, supplies, grounds, sensor and actuator examples. Consult the documented firmware and circuit protection conditions; identify connector keyways and view direction before counting pins. A shared input or output can perform only the function assigned to it.
Power and sensor plugs are distinct 34-way connectors. The power connector is shown with three keyways, the sensor connector with four; each set of pin numbers begins at 1. DTAFast's S60 Pro wiring diagram is dated 18 November 2014 and specifies firmware V77.00 or later for all illustrated options. Both connector views are drawn from the pin-insertion side. These tables transcribe the functions shown; unlisted pins are not established as unused. Slash-separated labels are alternatives or configuration-dependent functions.
Power connections
Pin
Documented function
1
Coil 3
2
Aux 6 / tacho
3
Fuel pump relay
4
Aux 2 / fan relay
5
Aux 1 / cam control
6
Aux 5 / shift light / electric dump valve
7
Turbo pressure valve
8
Idle valve
9
Injector 1
10
Coil 1
13, 14
Power grounds
17
Injector 2
18
Coil 2
25
Injector 4
26
Coil 4
31
Fused 12 V supply
32
ALS valve / VTEC / Aux 4
33
Aux 3 / VTEC / Bosch 3-pin idle valve fast side
34
Injector 3
Sensor connections
Pin
Documented function
1
Analogue 2 / log switch / TPS 2
2
Undriven wheel speed, Hall effect
3
Analogue 3 / gear potentiometer
4
Launch button
5
Oil pressure
6
Fuel pressure
7
Air temperature
9
5 V output
10
Analogue 1 / traction cut percentage / launch RPM
12
Crank magnetic
13
Crank Hall effect
14
Shift cut / E85 / air-con / shaft speed
15
ALS / map 2 / lambda switch
16
Manifold / barometric pressure
17
Oil temperature
19
Lambda signal
21, 33
Sensor ground
22
Cam magnetic
23
Cam Hall effect
25
Water temperature
26
CAN high
28
CAN low
34
Throttle position
The manufacturer diagram identifies the power connector's coil and injector outputs by firing order, not necessarily cylinder number. Separate crank and cam Hall and magnetic inputs are alternatives: the diagram says to use only one type per sensor. Check the exact model, keying, orientation, calibration and electrical ratings in the original diagram before wiring.
Revision 3: DTAFast S60 ProDTAFast S-series range, illustrative family photograph: DTAFast. The image is not a model-specific identification. Permission to republish confirmed by the user.
The DTAFast S60 Pro is an S-series programmable engine-management unit. Four injector and four coil drivers. The historical manufacturer product sheet describes four-cylinder sequential injection and coil-per-plug ignition, or up to eight cylinders with non-sequential injection and wasted spark; it supports one cam control. DTAFast historical S-series feature matrix.
Hardware and operation
The manufacturer's diagram labels separate power and sensor connectors and says output numbering follows firing order, not cylinder number. A cam sensor is required for sequential operation; the diagram specifies firmware V77.00 or newer for all illustrated options. Confirm the complete ECU label and revision; similarly named S-series units are separate records, and S-series capability differs from T-series. Record the number of injectors, coil arrangement, cam triggers and assigned auxiliary outputs before selecting a calibration.
Wiring and pinout
DTAFast S60 connector pinout and wiring gives connector views, supplies, grounds, sensor and actuator examples. Consult the documented firmware and circuit protection conditions; identify connector keyways and view direction before counting pins. A shared input or output can perform only the function assigned to it.
Power and sensor plugs are distinct 34-way connectors. The power connector is shown with three keyways, the sensor connector with four; each set of pin numbers begins at 1. DTAFast's S60 Pro wiring diagram is dated 18 November 2014 and specifies firmware V77.00 or later for all illustrated options. Both connector views are drawn from the pin-insertion side. These tables transcribe the functions shown; unlisted pins are not established as unused. Slash-separated labels are alternatives or configuration-dependent functions.
Power connections
Pin
Documented function
1
Coil 3
2
Aux 6 / tacho
3
Fuel pump relay
4
Aux 2 / fan relay
5
Aux 1 / cam control
6
Aux 5 / shift light / electric dump valve
7
Turbo pressure valve
8
Idle valve
9
Injector 1
10
Coil 1
13, 14
Power grounds
17
Injector 2
18
Coil 2
25
Injector 4
26
Coil 4
31
Fused 12 V supply
32
ALS valve / VTEC / Aux 4
33
Aux 3 / VTEC / Bosch 3-pin idle valve fast side
34
Injector 3
Sensor connections
Pin
Documented function
1
Analogue 2 / log switch / TPS 2
2
Undriven wheel speed, Hall effect
3
Analogue 3 / gear potentiometer
4
Launch button
5
Oil pressure
6
Fuel pressure
7
Air temperature
9
5 V output
10
Analogue 1 / traction cut percentage / launch RPM
12
Crank magnetic
13
Crank Hall effect
14
Shift cut / E85 / air-con / shaft speed
15
ALS / map 2 / lambda switch
16
Manifold / barometric pressure
17
Oil temperature
19
Lambda signal
21, 33
Sensor ground
22
Cam magnetic
23
Cam Hall effect
25
Water temperature
26
CAN high
28
CAN low
34
Throttle position
The manufacturer diagram identifies the power connector's coil and injector outputs by firing order, not necessarily cylinder number. Separate crank and cam Hall and magnetic inputs are alternatives: the diagram says to use only one type per sensor. Check the exact model, keying, orientation, calibration and electrical ratings in the original diagram before wiring.