Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
DTAFast standalone engine management
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None
DTAFast S-series ECU range
DTAFast S-series range, illustrative family photograph: DTAFast. The image is not a model-specific identification. Permission to republish confirmed by the user.

The DTAFast S60 Pro is an S-series programmable engine-management unit. Four injector and four coil drivers. The historical manufacturer product sheet describes four-cylinder sequential injection and coil-per-plug ignition, or up to eight cylinders with non-sequential injection and wasted spark; it supports one cam control. DTAFast historical S-series feature matrix.

Hardware and operation

The manufacturer's diagram labels separate power and sensor connectors and says output numbering follows firing order, not cylinder number. A cam sensor is required for sequential operation; the diagram specifies firmware V77.00 or newer for all illustrated options. Confirm the complete ECU label and revision; similarly named S-series units are separate records, and S-series capability differs from T-series. Record the number of injectors, coil arrangement, cam triggers and assigned auxiliary outputs before selecting a calibration.

Wiring and pinout

DTAFast S60 connector pinout and wiring gives connector views, supplies, grounds, sensor and actuator examples. Consult the documented firmware and circuit protection conditions; identify connector keyways and view direction before counting pins. A shared input or output can perform only the function assigned to it.

Software and additional references

The DTAFast S-series Pro manual describes DTASwin calibration software, data logging and model-specific settings. DTAFast S60 Pro product sheet provides an example of output and engine configuration limits. See the DTAFast model family for other ECUs.

S60 Pro pinout — manufacturer diagram

Power and sensor plugs are distinct 34-way connectors. The power connector is shown with three keyways, the sensor connector with four; each set of pin numbers begins at 1. DTAFast's S60 Pro wiring diagram is dated 18 November 2014 and specifies firmware V77.00 or later for all illustrated options. Both connector views are drawn from the pin-insertion side. These tables transcribe the functions shown; unlisted pins are not established as unused. Slash-separated labels are alternatives or configuration-dependent functions.

Power connections

PinDocumented function
1Coil 3
2Aux 6 / tacho
3Fuel pump relay
4Aux 2 / fan relay
5Aux 1 / cam control
6Aux 5 / shift light / electric dump valve
7Turbo pressure valve
8Idle valve
9Injector 1
10Coil 1
13, 14Power grounds
17Injector 2
18Coil 2
25Injector 4
26Coil 4
31Fused 12 V supply
32ALS valve / VTEC / Aux 4
33Aux 3 / VTEC / Bosch 3-pin idle valve fast side
34Injector 3

Sensor connections

PinDocumented function
1Analogue 2 / log switch / TPS 2
2Undriven wheel speed, Hall effect
3Analogue 3 / gear potentiometer
4Launch button
5Oil pressure
6Fuel pressure
7Air temperature
95 V output
10Analogue 1 / traction cut percentage / launch RPM
12Crank magnetic
13Crank Hall effect
14Shift cut / E85 / air-con / shaft speed
15ALS / map 2 / lambda switch
16Manifold / barometric pressure
17Oil temperature
19Lambda signal
21, 33Sensor ground
22Cam magnetic
23Cam Hall effect
25Water temperature
26CAN high
28CAN low
34Throttle position

The manufacturer diagram identifies the power connector's coil and injector outputs by firing order, not necessarily cylinder number. Separate crank and cam Hall and magnetic inputs are alternatives: the diagram says to use only one type per sensor. Check the exact model, keying, orientation, calibration and electrical ratings in the original diagram before wiring.