Removed text is struck through; added text is highlighted.
Manufacturer product image of EVO3X application ECU: Link ECU. Permission to republish confirmed by the user.
Link G4X EVO3X is a vehicle-specific programmable plug-in ECU for the Mitsubishi Evo I–III application listed in Link's model-specific manuals index. It is an application board, rather than the universal wire-in ECU. Check the exact vehicle, market, engine, original ECU and board part number against the manufacturer's EVO3X installation manual.
Identification and installation
Record the Link model label and revision, donor factory ECU connector and car's engine and year. Plug-in boards connect to particular factory-harness layouts; the family or vehicle name alone does not establish every model-year or transmission combination. The manufacturer manual gives the supported application and any installation or configuration notes for this board.
G4X plug-in platforms offer configurable fuel and ignition control but available channels and features depend on the original header and board. The G4X plug-in general specifications are conditional on the particular application and do not mean every input is brought out to the factory harness.
Pinout and tuning
The EVO3X installation manual is the model-specific source for board pinouts, expansion connections, electrical cautions and startup configuration. Use its connector orientation and the exact board version; do not copy a wire-in ECU pinout onto a factory harness. PCLink and manual downloads; Link manufacturer overview.
EVO3X main header and expansion pinoutFrom Link’s EVOLink I–III installation manual, pages 14–16. The manufacturer’s view is into the ECU from the wire side. “nc” is reproduced from Link’s table; pin numbers 27–30 and 47–50 are not listed there. Check the exact vehicle and board revision before wiring.PinECU channelExample vehicle function1Injector 1Injection2Injector 3Injection3Injector 5 (Aux)Fan speed relay4Aux 5ISC stepper5Aux 7ISC stepper6nc7nc8Aux 1Fuel pump relay9nc10Ignition 1Ignition cylinders 1 & 411DI 5A/C switch (EVO III only)12+14 V main relayECU power13Ground14Injector 2Injection15Injector 4Injection16Injector 6 (Aux)Engine fan17Aux 6ISC stepper18Aux 8ISC stepper19nc20nc21Injector 6 (Aux)Engine fan22Aux 2A/C clutch relay23Ignition 2Ignition cylinders 2 & 324nc25+14 V main relayECU power26Ground31nc32nc33Ignition 3 (Aux)Fuel pressure solenoid34nc35nc36Injector 7 (Aux)CE light37DI 6Power steering switch38Ignition 4ECU hold power39Aux 3MIVEC solenoid, MIVEC Mirage CA4A only40Aux 4Wastegate solenoid41nc42nc43nc44nc45DI 1A/C request46nc51DI 2Start signal52An Temp 2MAF IAT53nc54nc55nc56An Volt 4Oxygen signal57nc58Knock 1Knock59nc60nc (constant +12 V)61+5 V Out62DI 3Ignition switch63An Temp 1ECT64An Volt 3TPS signal65nc66DI 4Vehicle speed67DI 7Idle switch68Trig 2Trigger 269Trig 1Trigger 170An Volt 2MAF signal71Ground72Ground (signal)Link lists injector 6 (Aux) at both pins 16 and 21 for the engine fan; verify the vehicle wiring. Injector drive 8 is not exposed and lacks hardware for driving an injector. The on-board MAP uses An Volt 1.Expansion connectorPinECU channel1Ground (signal)2+5 V Out3DI 84DI 95An Volt 56An Volt 67An Temp 38An Temp 49Ignition 510Ignition 611Ignition 712Ignition 813An Volt 814An Volt 915An Volt 1016An Volt 11CAN 1 / RS232PinFunction / cable colour1Comms GND (brown)2CAN1 L (green)3CAN1 H (white)4RS232 RX (grey)5RS232 TX (yellow)CAN 2 / OBDPinFunction / cable colour1GND (brown)2CAN2 L (green)3CAN2 H (white)4NC (grey)5+14 V (yellow)Link cautions that serial wires connected to the CAN 1/RS232 plug can interfere with USB communication when used for CAN.
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 2: Link G4X EVO3X plug-in ECUManufacturer product image of EVO3X application ECU: Link ECU. Permission to republish confirmed by the user.
Link G4X EVO3X is a vehicle-specific programmable plug-in ECU for the Mitsubishi Evo I–III application listed in Link's model-specific manuals index. It is an application board, rather than the universal wire-in ECU. Check the exact vehicle, market, engine, original ECU and board part number against the manufacturer's EVO3X installation manual.
Identification and installation
Record the Link model label and revision, donor factory ECU connector and car's engine and year. Plug-in boards connect to particular factory-harness layouts; the family or vehicle name alone does not establish every model-year or transmission combination. The manufacturer manual gives the supported application and any installation or configuration notes for this board.
G4X plug-in platforms offer configurable fuel and ignition control but available channels and features depend on the original header and board. The G4X plug-in general specifications are conditional on the particular application and do not mean every input is brought out to the factory harness.
Pinout and tuning
The EVO3X installation manual is the model-specific source for board pinouts, expansion connections, electrical cautions and startup configuration. Use its connector orientation and the exact board version; do not copy a wire-in ECU pinout onto a factory harness. PCLink and manual downloads; Link manufacturer overview.
Revision 3: Link G4X EVO3X plug-in ECUManufacturer product image of EVO3X application ECU: Link ECU. Permission to republish confirmed by the user.
Link G4X EVO3X is a vehicle-specific programmable plug-in ECU for the Mitsubishi Evo I–III application listed in Link's model-specific manuals index. It is an application board, rather than the universal wire-in ECU. Check the exact vehicle, market, engine, original ECU and board part number against the manufacturer's EVO3X installation manual.
Identification and installation
Record the Link model label and revision, donor factory ECU connector and car's engine and year. Plug-in boards connect to particular factory-harness layouts; the family or vehicle name alone does not establish every model-year or transmission combination. The manufacturer manual gives the supported application and any installation or configuration notes for this board.
G4X plug-in platforms offer configurable fuel and ignition control but available channels and features depend on the original header and board. The G4X plug-in general specifications are conditional on the particular application and do not mean every input is brought out to the factory harness.
Pinout and tuning
The EVO3X installation manual is the model-specific source for board pinouts, expansion connections, electrical cautions and startup configuration. Use its connector orientation and the exact board version; do not copy a wire-in ECU pinout onto a factory harness. PCLink and manual downloads; Link manufacturer overview.
EVO3X main header and expansion pinout
From Link’s EVOLink I–III installation manual, pages 14–16. The manufacturer’s view is into the ECU from the wire side. “nc” is reproduced from Link’s table; pin numbers 27–30 and 47–50 are not listed there. Check the exact vehicle and board revision before wiring.
Pin
ECU channel
Example vehicle function
1
Injector 1
Injection
2
Injector 3
Injection
3
Injector 5 (Aux)
Fan speed relay
4
Aux 5
ISC stepper
5
Aux 7
ISC stepper
6
nc
7
nc
8
Aux 1
Fuel pump relay
9
nc
10
Ignition 1
Ignition cylinders 1 & 4
11
DI 5
A/C switch (EVO III only)
12
+14 V main relay
ECU power
13
Ground
14
Injector 2
Injection
15
Injector 4
Injection
16
Injector 6 (Aux)
Engine fan
17
Aux 6
ISC stepper
18
Aux 8
ISC stepper
19
nc
20
nc
21
Injector 6 (Aux)
Engine fan
22
Aux 2
A/C clutch relay
23
Ignition 2
Ignition cylinders 2 & 3
24
nc
25
+14 V main relay
ECU power
26
Ground
31
nc
32
nc
33
Ignition 3 (Aux)
Fuel pressure solenoid
34
nc
35
nc
36
Injector 7 (Aux)
CE light
37
DI 6
Power steering switch
38
Ignition 4
ECU hold power
39
Aux 3
MIVEC solenoid, MIVEC Mirage CA4A only
40
Aux 4
Wastegate solenoid
41
nc
42
nc
43
nc
44
nc
45
DI 1
A/C request
46
nc
51
DI 2
Start signal
52
An Temp 2
MAF IAT
53
nc
54
nc
55
nc
56
An Volt 4
Oxygen signal
57
nc
58
Knock 1
Knock
59
nc
60
nc (constant +12 V)
61
+5 V Out
62
DI 3
Ignition switch
63
An Temp 1
ECT
64
An Volt 3
TPS signal
65
nc
66
DI 4
Vehicle speed
67
DI 7
Idle switch
68
Trig 2
Trigger 2
69
Trig 1
Trigger 1
70
An Volt 2
MAF signal
71
Ground
72
Ground (signal)
Link lists injector 6 (Aux) at both pins 16 and 21 for the engine fan; verify the vehicle wiring. Injector drive 8 is not exposed and lacks hardware for driving an injector. The on-board MAP uses An Volt 1.
Expansion connector
Pin
ECU channel
1
Ground (signal)
2
+5 V Out
3
DI 8
4
DI 9
5
An Volt 5
6
An Volt 6
7
An Temp 3
8
An Temp 4
9
Ignition 5
10
Ignition 6
11
Ignition 7
12
Ignition 8
13
An Volt 8
14
An Volt 9
15
An Volt 10
16
An Volt 11
CAN 1 / RS232
Pin
Function / cable colour
1
Comms GND (brown)
2
CAN1 L (green)
3
CAN1 H (white)
4
RS232 RX (grey)
5
RS232 TX (yellow)
CAN 2 / OBD
Pin
Function / cable colour
1
GND (brown)
2
CAN2 L (green)
3
CAN2 H (white)
4
NC (grey)
5
+14 V (yellow)
Link cautions that serial wires connected to the CAN 1/RS232 plug can interfere with USB communication when used for CAN.