Removed text is struck through; added text is highlighted.
ECUMaster EMU Black Lotus 2ZZ-GE plug-in. Product photo: ECUMaster plug-in ECU catalogue; reproduced with permission.
The manufacturer catalogue specifies the drive-by-wire Lotus 2ZZ-GE plug-in. Manual v2.0 is for EMU Black software 2.169 or later and documents naturally aspirated and supercharged variants, OEM CAN, variable valve lift and timing, and a stock 2ZZ base map. Actual installation depends on the engine and car specification. Model source · ECUMaster plug-in catalogue.
Wiring and pinout
The manual's page 8 describes wideband signal connections at the OEM Lotus connector. The following are the ECU terminal labels, not sensor connector pin numbers. The source gives separate Bosch LSU 4.2 and 4.9 sensor-side mappings and instructs disconnection of the OEM narrowband sensor when fitting wideband. Manufacturer model-specific document.
TerminalDocumented function3KWideband heater4EWideband Ip3AWideband Vs3DWideband Rcal4FWideband VGnd3G+12 V
Spare factory terminals — manual v2.0The manufacturer's spare-I/O table lists these positions on otherwise unused OEM ECU terminals. This is not a complete factory connector pinout.ECU terminalManual function1GEGT input 12CRS232 TX3CRS232 RX3DWideband Rcal3FEGT input 24EWideband Ip4FWideband VGnd3AKnock sensor input 2 (source conflicts; see below)3LFlex fuel inputConflicting source: The same manual assigns terminal 3A to wideband Vs in its wideband wiring table and knock sensor input 2 in the spare-I/O table. Confirm the correct assignment with ECUMaster for the specific ECU before wiring.Wideband connector mappingSensor-side terminals differ between LSU 4.2 and 4.9. The manual directs that the original narrowband sensor be disconnected before installing a wideband.ECU terminalFunctionLSU 4.2 terminalLSU 4.9 terminal3KHeater434EIp613AVs (conflicts with spare-I/O table)163DRcal254FVGnd523G+12 V34
Calibration and fitment checks
Record the engine code, ECU label and hardware, factory wiring and software version. The manufacturer provides software, available application notes and base maps; a base map is a starting point requiring checks of sensor readings, throttle operation, injector and ignition settings, trigger timing and engine calibration. Do not transfer universal EMU Black pin numbers or another plug-in's auxiliary connector assignments to this unit.
See the EMU Black model page and manufacturer index.
Other 2ZZ arrangements
The ECU manual lists separate CAN dashboard settings for 2ZZ electronic throttle, cable throttle and Lotus S3 2ZZ; a selectable software mode alone does not prove that one physical plug-in ECU fits every harness. RRR separately sells a Lotus S2 2ZZ cable-throttle adapter kit using an EMU Black. Identify the kit and adapter maker and obtain the matching wiring instructions; it is not established to be the same integrated ECU as the ECUMaster DBW plug-in.
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 2: ECUMaster EMU Black Lotus 2ZZ-GE plug-inECUMaster EMU Black Lotus 2ZZ-GE plug-in. Product photo: ECUMaster plug-in ECU catalogue; reproduced with permission.
The manufacturer catalogue specifies the drive-by-wire Lotus 2ZZ-GE plug-in. Manual v2.0 is for EMU Black software 2.169 or later and documents naturally aspirated and supercharged variants, OEM CAN, variable valve lift and timing, and a stock 2ZZ base map. Actual installation depends on the engine and car specification. Model source · ECUMaster plug-in catalogue.
Wiring and pinout
The manual's page 8 describes wideband signal connections at the OEM Lotus connector. The following are the ECU terminal labels, not sensor connector pin numbers. The source gives separate Bosch LSU 4.2 and 4.9 sensor-side mappings and instructs disconnection of the OEM narrowband sensor when fitting wideband. Manufacturer model-specific document.
Terminal
Documented function
3K
Wideband heater
4E
Wideband Ip
3A
Wideband Vs
3D
Wideband Rcal
4F
Wideband VGnd
3G
+12 V
Calibration and fitment checks
Record the engine code, ECU label and hardware, factory wiring and software version. The manufacturer provides software, available application notes and base maps; a base map is a starting point requiring checks of sensor readings, throttle operation, injector and ignition settings, trigger timing and engine calibration. Do not transfer universal EMU Black pin numbers or another plug-in's auxiliary connector assignments to this unit.
The ECU manual lists separate CAN dashboard settings for 2ZZ electronic throttle, cable throttle and Lotus S3 2ZZ; a selectable software mode alone does not prove that one physical plug-in ECU fits every harness. RRR separately sells a Lotus S2 2ZZ cable-throttle adapter kit using an EMU Black. Identify the kit and adapter maker and obtain the matching wiring instructions; it is not established to be the same integrated ECU as the ECUMaster DBW plug-in.
Revision 3: ECUMaster EMU Black Lotus 2ZZ-GE plug-inECUMaster EMU Black Lotus 2ZZ-GE plug-in. Product photo: ECUMaster plug-in ECU catalogue; reproduced with permission.
The manufacturer catalogue specifies the drive-by-wire Lotus 2ZZ-GE plug-in. Manual v2.0 is for EMU Black software 2.169 or later and documents naturally aspirated and supercharged variants, OEM CAN, variable valve lift and timing, and a stock 2ZZ base map. Actual installation depends on the engine and car specification. Model source · ECUMaster plug-in catalogue.
Wiring and pinout
The manual's page 8 describes wideband signal connections at the OEM Lotus connector. The following are the ECU terminal labels, not sensor connector pin numbers. The source gives separate Bosch LSU 4.2 and 4.9 sensor-side mappings and instructs disconnection of the OEM narrowband sensor when fitting wideband. Manufacturer model-specific document.
Terminal
Documented function
3K
Wideband heater
4E
Wideband Ip
3A
Wideband Vs
3D
Wideband Rcal
4F
Wideband VGnd
3G
+12 V
Spare factory terminals — manual v2.0
The manufacturer's spare-I/O table lists these positions on otherwise unused OEM ECU terminals. This is not a complete factory connector pinout.
ECU terminal
Manual function
1G
EGT input 1
2C
RS232 TX
3C
RS232 RX
3D
Wideband Rcal
3F
EGT input 2
4E
Wideband Ip
4F
Wideband VGnd
3A
Knock sensor input 2 (source conflicts; see below)
3L
Flex fuel input
Conflicting source: The same manual assigns terminal 3A to wideband Vs in its wideband wiring table and knock sensor input 2 in the spare-I/O table. Confirm the correct assignment with ECUMaster for the specific ECU before wiring.
Wideband connector mapping
Sensor-side terminals differ between LSU 4.2 and 4.9. The manual directs that the original narrowband sensor be disconnected before installing a wideband.
ECU terminal
Function
LSU 4.2 terminal
LSU 4.9 terminal
3K
Heater
4
3
4E
Ip
6
1
3A
Vs (conflicts with spare-I/O table)
1
6
3D
Rcal
2
5
4F
VGnd
5
2
3G
+12 V
3
4
Calibration and fitment checks
Record the engine code, ECU label and hardware, factory wiring and software version. The manufacturer provides software, available application notes and base maps; a base map is a starting point requiring checks of sensor readings, throttle operation, injector and ignition settings, trigger timing and engine calibration. Do not transfer universal EMU Black pin numbers or another plug-in's auxiliary connector assignments to this unit.
The ECU manual lists separate CAN dashboard settings for 2ZZ electronic throttle, cable throttle and Lotus S3 2ZZ; a selectable software mode alone does not prove that one physical plug-in ECU fits every harness. RRR separately sells a Lotus S2 2ZZ cable-throttle adapter kit using an EMU Black. Identify the kit and adapter maker and obtain the matching wiring instructions; it is not established to be the same integrated ECU as the ECUMaster DBW plug-in.