Removed text is struck through; added text is highlighted.
MaxxECU Mitsubishi EVO IV - VIII plug-in product image. Source: MaxxECU; used with permission. Illustrative kit; confirm included hardware for the particular package.
MaxxECU Mitsubishi EVO IV - VIII plug-in adapter connects a compatible MaxxECU to an application-specific factory wiring loom. It is an adapter and installation package rather than a new universal ECU architecture. The published MaxxECU application guide identifies its intended configuration and connector details.
Identification and scope
Match the vehicle, engine, original ECU and connector, transmission, adapter revision and the MaxxECU unit to the guide. GEN1 adapters and earlier V1-specific adapters are not automatically interchangeable. The manufacturer's GEN1 adapter index separates the vehicle-specific instructions.
Manufacturer-listed examples
These examples and qualifications are transcribed from the manufacturer's adapter guide. A listed platform is not proof that every market or hardware combination is compatible; check the exact ECU, loom and transmission.
VehicleEngine codeYearLSU sensorNoteMitsubishi EVO 44G63T1996 - 1998External LSU neededMitsubishi EVO 54G63T1998 - 1999External LSU neededMitsubishi EVO 64G63T1999 - 2001External LSU neededMitsubishi EVO 74G63T2001 - 2003External LSU neededMitsubishi EVO 84G63T2003 - 2005External LSU needed
Vehicle and ECU functions
Manufacturer's mapping and availability for this particular adapter; a yes or no applies only to the configuration named in the table. Confirm adapter revision, hardware and calibration with the original guide.
EVO 4,5,6EVO 7,8MaxxECU IOV1/RACE/PRONoteAC clutchFuel pump (main)GPO 3YesFuel pump (stage 2)-GPO 5YesLower the fuel pump capacity on EVO VIII...TachometerTachometerGPO 8YesCheck engine lightCheck engine lightGPO 2YesIdle stepperIdle stepperINJ 5,6,7,8YesBoost solenoidBoost solenoidGPO 4YesUses stock solenoidEngine FANs (high + low)Engine fan (PWM)GPO 6YesVehicle speedVehicle speedDIN 1YesFuel pump (stage 1)AC clutch + AC FANGPO 1YesAC requestAC requestDIN 2Yes-EVAP valveGPO 7YesAlso connected to extra 16-pin connector-Clutch switch-No-Intercooler sprayer-No-Sec air system solenoid-No-Evap vent solenoid-NoIdle position switchAYC/ACD signal-No-EGR-NoBluetooth ( MDash)Bluetooth ( MDash)-YesKnock sensor(s)Knock sensor(s)-NoEGT optionEGT option-Yes, direct
Additional connector
The following is the extra connector table in the model-specific guide. Refer to its illustrated connector and installation notes for view, cable colours, electrical limits and revision; these positions are not the factory ECU connector.
PinDescriptionUsageNote1Wide band (VREF)2Wide band (VS)3Wide band (shield)4Wide band (H-)56-7-8GPO 7 / DIN 3Output or digital inputParallel connected to stock EVAP solenoid, to use this, EVAP solenoid connector MUST be disconnected9Wide band (IP)10Wide band (RCAL)11+12VOutput12+12VOutput13Engine GND14AIN 30-5V analog input15AIN 1temperature input16AIN 2temperature input
Installation and verification
The adapter may require an external wideband sensor, a MAP hose, additional connectors, or other changes depending on the application and kit. Do not assume that every factory function, emissions device, dashboard feature, air-conditioning function or transmission is supported. Check the model-specific tables, base configuration and full manufacturer installation guide for the exact unit before connection and calibration.
Documents
MaxxECU Mitsubishi EVO IV - VIII adapter installation and pinoutGEN1 plug-in compatibility and wiring indexMaxxECU manufacturer and universal-model index
Sources reviewed 17 November 2026.
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 2: MaxxECU Mitsubishi EVO IV - VIII plug-in adapterMaxxECU Mitsubishi EVO IV - VIII plug-in product image. Source: MaxxECU; used with permission. Illustrative kit; confirm included hardware for the particular package.
MaxxECU Mitsubishi EVO IV - VIII plug-in adapter connects a compatible MaxxECU to an application-specific factory wiring loom. It is an adapter and installation package rather than a new universal ECU architecture. The published MaxxECU application guide identifies its intended configuration and connector details.
Identification and scope
Match the vehicle, engine, original ECU and connector, transmission, adapter revision and the MaxxECU unit to the guide. GEN1 adapters and earlier V1-specific adapters are not automatically interchangeable. The manufacturer's GEN1 adapter index separates the vehicle-specific instructions.
Manufacturer-listed examples
These examples and qualifications are transcribed from the manufacturer's adapter guide. A listed platform is not proof that every market or hardware combination is compatible; check the exact ECU, loom and transmission.
Vehicle
Engine code
Year
LSU sensor
Note
Mitsubishi EVO 4
4G63T
1996 - 1998
External LSU needed
Mitsubishi EVO 5
4G63T
1998 - 1999
External LSU needed
Mitsubishi EVO 6
4G63T
1999 - 2001
External LSU needed
Mitsubishi EVO 7
4G63T
2001 - 2003
External LSU needed
Mitsubishi EVO 8
4G63T
2003 - 2005
External LSU needed
Vehicle and ECU functions
Manufacturer's mapping and availability for this particular adapter; a yes or no applies only to the configuration named in the table. Confirm adapter revision, hardware and calibration with the original guide.
EVO 4,5,6
EVO 7,8
MaxxECU IO
V1/RACE/PRO
Note
AC clutch
Fuel pump (main)
GPO 3
Yes
Fuel pump (stage 2)
-
GPO 5
Yes
Lower the fuel pump capacity on EVO VIII...
Tachometer
Tachometer
GPO 8
Yes
Check engine light
Check engine light
GPO 2
Yes
Idle stepper
Idle stepper
INJ 5,6,7,8
Yes
Boost solenoid
Boost solenoid
GPO 4
Yes
Uses stock solenoid
Engine FANs (high + low)
Engine fan (PWM)
GPO 6
Yes
Vehicle speed
Vehicle speed
DIN 1
Yes
Fuel pump (stage 1)
AC clutch + AC FAN
GPO 1
Yes
AC request
AC request
DIN 2
Yes
-
EVAP valve
GPO 7
Yes
Also connected to extra 16-pin connector
-
Clutch switch
-
No
-
Intercooler sprayer
-
No
-
Sec air system solenoid
-
No
-
Evap vent solenoid
-
No
Idle position switch
AYC/ACD signal
-
No
-
EGR
-
No
Bluetooth ( MDash)
Bluetooth ( MDash)
-
Yes
Knock sensor(s)
Knock sensor(s)
-
No
EGT option
EGT option
-
Yes, direct
Additional connector
The following is the extra connector table in the model-specific guide. Refer to its illustrated connector and installation notes for view, cable colours, electrical limits and revision; these positions are not the factory ECU connector.
Pin
Description
Usage
Note
1
Wide band (VREF)
2
Wide band (VS)
3
Wide band (shield)
4
Wide band (H-)
5
6
-
7
-
8
GPO 7 / DIN 3
Output or digital input
Parallel connected to stock EVAP solenoid, to use this, EVAP solenoid connector MUST be disconnected
9
Wide band (IP)
10
Wide band (RCAL)
11
+12V
Output
12
+12V
Output
13
Engine GND
14
AIN 3
0-5V analog input
15
AIN 1
temperature input
16
AIN 2
temperature input
Installation and verification
The adapter may require an external wideband sensor, a MAP hose, additional connectors, or other changes depending on the application and kit. Do not assume that every factory function, emissions device, dashboard feature, air-conditioning function or transmission is supported. Check the model-specific tables, base configuration and full manufacturer installation guide for the exact unit before connection and calibration.
Revision 2: MaxxECU Mitsubishi EVO IV - VIII plug-in adapterMaxxECU Mitsubishi EVO IV - VIII plug-in product image. Source: MaxxECU; used with permission. Illustrative kit; confirm included hardware for the particular package.
MaxxECU Mitsubishi EVO IV - VIII plug-in adapter connects a compatible MaxxECU to an application-specific factory wiring loom. It is an adapter and installation package rather than a new universal ECU architecture. The published MaxxECU application guide identifies its intended configuration and connector details.
Identification and scope
Match the vehicle, engine, original ECU and connector, transmission, adapter revision and the MaxxECU unit to the guide. GEN1 adapters and earlier V1-specific adapters are not automatically interchangeable. The manufacturer's GEN1 adapter index separates the vehicle-specific instructions.
Manufacturer-listed examples
These examples and qualifications are transcribed from the manufacturer's adapter guide. A listed platform is not proof that every market or hardware combination is compatible; check the exact ECU, loom and transmission.
Vehicle
Engine code
Year
LSU sensor
Note
Mitsubishi EVO 4
4G63T
1996 - 1998
External LSU needed
Mitsubishi EVO 5
4G63T
1998 - 1999
External LSU needed
Mitsubishi EVO 6
4G63T
1999 - 2001
External LSU needed
Mitsubishi EVO 7
4G63T
2001 - 2003
External LSU needed
Mitsubishi EVO 8
4G63T
2003 - 2005
External LSU needed
Vehicle and ECU functions
Manufacturer's mapping and availability for this particular adapter; a yes or no applies only to the configuration named in the table. Confirm adapter revision, hardware and calibration with the original guide.
EVO 4,5,6
EVO 7,8
MaxxECU IO
V1/RACE/PRO
Note
AC clutch
Fuel pump (main)
GPO 3
Yes
Fuel pump (stage 2)
-
GPO 5
Yes
Lower the fuel pump capacity on EVO VIII...
Tachometer
Tachometer
GPO 8
Yes
Check engine light
Check engine light
GPO 2
Yes
Idle stepper
Idle stepper
INJ 5,6,7,8
Yes
Boost solenoid
Boost solenoid
GPO 4
Yes
Uses stock solenoid
Engine FANs (high + low)
Engine fan (PWM)
GPO 6
Yes
Vehicle speed
Vehicle speed
DIN 1
Yes
Fuel pump (stage 1)
AC clutch + AC FAN
GPO 1
Yes
AC request
AC request
DIN 2
Yes
-
EVAP valve
GPO 7
Yes
Also connected to extra 16-pin connector
-
Clutch switch
-
No
-
Intercooler sprayer
-
No
-
Sec air system solenoid
-
No
-
Evap vent solenoid
-
No
Idle position switch
AYC/ACD signal
-
No
-
EGR
-
No
Bluetooth ( MDash)
Bluetooth ( MDash)
-
Yes
Knock sensor(s)
Knock sensor(s)
-
No
EGT option
EGT option
-
Yes, direct
Additional connector
The following is the extra connector table in the model-specific guide. Refer to its illustrated connector and installation notes for view, cable colours, electrical limits and revision; these positions are not the factory ECU connector.
Pin
Description
Usage
Note
1
Wide band (VREF)
2
Wide band (VS)
3
Wide band (shield)
4
Wide band (H-)
5
6
-
7
-
8
GPO 7 / DIN 3
Output or digital input
Parallel connected to stock EVAP solenoid, to use this, EVAP solenoid connector MUST be disconnected
9
Wide band (IP)
10
Wide band (RCAL)
11
+12V
Output
12
+12V
Output
13
Engine GND
14
AIN 3
0-5V analog input
15
AIN 1
temperature input
16
AIN 2
temperature input
Installation and verification
The adapter may require an external wideband sensor, a MAP hose, additional connectors, or other changes depending on the application and kit. Do not assume that every factory function, emissions device, dashboard feature, air-conditioning function or transmission is supported. Check the model-specific tables, base configuration and full manufacturer installation guide for the exact unit before connection and calibration.