Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
MaxxECU standalone engine management
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None
MaxxECU Mitsubishi EVO IV - VIII plug-in kit
MaxxECU Mitsubishi EVO IV - VIII plug-in product image. Source: MaxxECU; used with permission. Illustrative kit; confirm included hardware for the particular package.

MaxxECU Mitsubishi EVO IV - VIII plug-in adapter connects a compatible MaxxECU to an application-specific factory wiring loom. It is an adapter and installation package rather than a new universal ECU architecture. The published MaxxECU application guide identifies its intended configuration and connector details.

Identification and scope

Match the vehicle, engine, original ECU and connector, transmission, adapter revision and the MaxxECU unit to the guide. GEN1 adapters and earlier V1-specific adapters are not automatically interchangeable. The manufacturer's GEN1 adapter index separates the vehicle-specific instructions.

Manufacturer-listed examples

These examples and qualifications are transcribed from the manufacturer's adapter guide. A listed platform is not proof that every market or hardware combination is compatible; check the exact ECU, loom and transmission.

VehicleEngine codeYearLSU sensorNote
Mitsubishi EVO 44G63T1996 - 1998External LSU needed
Mitsubishi EVO 54G63T1998 - 1999External LSU needed
Mitsubishi EVO 64G63T1999 - 2001External LSU needed
Mitsubishi EVO 74G63T2001 - 2003External LSU needed
Mitsubishi EVO 84G63T2003 - 2005External LSU needed

Vehicle and ECU functions

Manufacturer's mapping and availability for this particular adapter; a yes or no applies only to the configuration named in the table. Confirm adapter revision, hardware and calibration with the original guide.

EVO 4,5,6EVO 7,8MaxxECU IOV1/RACE/PRONote
AC clutchFuel pump (main)GPO 3Yes
Fuel pump (stage 2)-GPO 5YesLower the fuel pump capacity on EVO VIII...
TachometerTachometerGPO 8Yes
Check engine lightCheck engine lightGPO 2Yes
Idle stepperIdle stepperINJ 5,6,7,8Yes
Boost solenoidBoost solenoidGPO 4YesUses stock solenoid
Engine FANs (high + low)Engine fan (PWM)GPO 6Yes
Vehicle speedVehicle speedDIN 1Yes
Fuel pump (stage 1)AC clutch + AC FANGPO 1Yes
AC requestAC requestDIN 2Yes
-EVAP valveGPO 7YesAlso connected to extra 16-pin connector
-Clutch switch-No
-Intercooler sprayer-No
-Sec air system solenoid-No
-Evap vent solenoid-No
Idle position switchAYC/ACD signal-No
-EGR-No
Bluetooth ( MDash)Bluetooth ( MDash)-Yes
Knock sensor(s)Knock sensor(s)-No
EGT optionEGT option-Yes, direct

Additional connector

The following is the extra connector table in the model-specific guide. Refer to its illustrated connector and installation notes for view, cable colours, electrical limits and revision; these positions are not the factory ECU connector.

PinDescriptionUsageNote
1Wide band (VREF)
2Wide band (VS)
3Wide band (shield)
4Wide band (H-)
5
6-
7-
8GPO 7 / DIN 3Output or digital inputParallel connected to stock EVAP solenoid, to use this, EVAP solenoid connector MUST be disconnected
9Wide band (IP)
10Wide band (RCAL)
11+12VOutput
12+12VOutput
13Engine GND
14AIN 30-5V analog input
15AIN 1temperature input
16AIN 2temperature input

Installation and verification

The adapter may require an external wideband sensor, a MAP hose, additional connectors, or other changes depending on the application and kit. Do not assume that every factory function, emissions device, dashboard feature, air-conditioning function or transmission is supported. Check the model-specific tables, base configuration and full manufacturer installation guide for the exact unit before connection and calibration.

Documents

Sources reviewed 17 November 2026.