Removed text is struck through; added text is highlighted.
MaxxECU Audi S4/RS4 2.7 biturbo (ME 7.1) plug-in product image. Source: MaxxECU; used with permission. Illustrative kit; confirm included hardware for the particular package.
MaxxECU Audi S4/RS4 2.7 biturbo (ME 7.1) plug-in adapter connects a compatible MaxxECU to an application-specific factory wiring loom. It is an adapter and installation package rather than a new universal ECU architecture. The published MaxxECU application guide identifies its intended configuration and connector details.
Identification and scope
Match the vehicle, engine, original ECU and connector, transmission, adapter revision and the MaxxECU unit to the guide. GEN1 adapters and earlier V1-specific adapters are not automatically interchangeable. The manufacturer's GEN1 adapter index separates the vehicle-specific instructions.
Manufacturer-listed examples
These examples and qualifications are transcribed from the manufacturer's adapter guide. A listed platform is not proof that every market or hardware combination is compatible; check the exact ECU, loom and transmission.
Manufacturer's mapping and availability for this particular adapter; a yes or no applies only to the configuration named in the table. Confirm adapter revision, hardware and calibration with the original guide.
OptionsOEM ECU PINMaxxECU IORACENoteVVT solenoid115GPO 1YesCheck engine light48GPO 2 + Audi ME 7.5 CANYesBoost solenoid (OEM)104GPO 4YesOnly on turbo enginesVariable intake valve121GPO 4YesOnly on Golf R32. Can be used to control the variable intake, or for boosted applications the boost solenoid (requires a solenoid to be wired to the valve solenoid connector)Fuel pump relay65GPO 5YesVVT exhaust solenoid120GPO 6YesParallel connected to extra 16-pin connector also if not used.Tachometer37GPO 8 + Audi ME 7.5 CANYesE-Throttle117/118GPO 11/12YesSequential injectionINJ 1 - 6YesIAC cutoff valve9INJ 7YesEVAP64INJ 8YesSequential ignitionIGN 1 - 6YesKnock sensors (OEM)106, 107KNOCK1, KNOCK2YesSecondary air pump44,46-NoIntake air temperature sensorIATYesParalell connected with 2-pin extra connectorCoolant temperature sensorCLTYesClutch switch39AIN 1YESBrake pedal56AIN 2YESVehicle speed (VSS)54DIN 1YesAlso from CAN, Audi ME 7.5 CANEPC light-Audi ME 7.5 CANCAN only!Instrument cluster/ABS-Audi ME 7.5 CANCAN only!Fuel consumptionNoCruise controlNoBluetooth ( MDash)YesEGT optionYes, direct6 EGT direct in harnessOEM EGT-sensorsNo
Additional connector
The following is the extra connector table in the model-specific guide. Refer to its illustrated connector and installation notes for view, cable colours, electrical limits and revision; these positions are not the factory ECU connector.
PinDescriptionUsageNote1 (H)+5V sensor supply2 (G)Sensor GND3 (F)TPS AIN0-5V analog input4 (E)AIN 40-5V analog input5 (D)DIN/VR 4Digital input6 (C)DIN/VR 5Digital input7 (B)GPO 6OutputAlso parallel connected to VVT exhaust valve (if your vehicle has one)8 (A)GPO 7 / DIN 3Output or digital input9 (S)10 (R)11 (P)12 (N)+12VOutput at ignition on13 (M)Engine GND14 (L)GPO 3Output15 (K)DIN 2Digital input16 (J)AIN 30-5V analog input
Installation and verification
The adapter may require an external wideband sensor, a MAP hose, additional connectors, or other changes depending on the application and kit. Do not assume that every factory function, emissions device, dashboard feature, air-conditioning function or transmission is supported. Check the model-specific tables, base configuration and full manufacturer installation guide for the exact unit before connection and calibration.
Documents
MaxxECU Audi S4/RS4 2.7 biturbo (ME 7.1) adapter installation and pinoutGEN1 plug-in compatibility and wiring indexMaxxECU manufacturer and universal-model index
Sources reviewed 17 November 2026.
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 2: MaxxECU Audi S4/RS4 2.7 biturbo (ME 7.1) plug-in adapterMaxxECU Audi S4/RS4 2.7 biturbo (ME 7.1) plug-in product image. Source: MaxxECU; used with permission. Illustrative kit; confirm included hardware for the particular package.
MaxxECU Audi S4/RS4 2.7 biturbo (ME 7.1) plug-in adapter connects a compatible MaxxECU to an application-specific factory wiring loom. It is an adapter and installation package rather than a new universal ECU architecture. The published MaxxECU application guide identifies its intended configuration and connector details.
Identification and scope
Match the vehicle, engine, original ECU and connector, transmission, adapter revision and the MaxxECU unit to the guide. GEN1 adapters and earlier V1-specific adapters are not automatically interchangeable. The manufacturer's GEN1 adapter index separates the vehicle-specific instructions.
Manufacturer-listed examples
These examples and qualifications are transcribed from the manufacturer's adapter guide. A listed platform is not proof that every market or hardware combination is compatible; check the exact ECU, loom and transmission.
Vehicle
Engine code
Year
LSU sensor
Note
Audi S4 B5 2.7 biturbo
AGB, AZB
1998 - 2002
External sensor needed
Only uses one WBO sensor
Audi RS4 2.7 biturbo
AZR
2001
External sensor needed
Only uses one WBO sensor
Golf R32
BDE
1997 - 2003
Uses stock LSU 4.2 sensor
Not available yet!!
Vehicle and ECU functions
Manufacturer's mapping and availability for this particular adapter; a yes or no applies only to the configuration named in the table. Confirm adapter revision, hardware and calibration with the original guide.
Options
OEM ECU PIN
MaxxECU IO
RACE
Note
VVT solenoid
115
GPO 1
Yes
Check engine light
48
GPO 2 + Audi ME 7.5 CAN
Yes
Boost solenoid (OEM)
104
GPO 4
Yes
Only on turbo engines
Variable intake valve
121
GPO 4
Yes
Only on Golf R32. Can be used to control the variable intake, or for boosted applications the boost solenoid (requires a solenoid to be wired to the valve solenoid connector)
Fuel pump relay
65
GPO 5
Yes
VVT exhaust solenoid
120
GPO 6
Yes
Parallel connected to extra 16-pin connector also if not used.
Tachometer
37
GPO 8 + Audi ME 7.5 CAN
Yes
E-Throttle
117/118
GPO 11/12
Yes
Sequential injection
INJ 1 - 6
Yes
IAC cutoff valve
9
INJ 7
Yes
EVAP
64
INJ 8
Yes
Sequential ignition
IGN 1 - 6
Yes
Knock sensors (OEM)
106, 107
KNOCK1, KNOCK2
Yes
Secondary air pump
44,46
-
No
Intake air temperature sensor
IAT
Yes
Paralell connected with 2-pin extra connector
Coolant temperature sensor
CLT
Yes
Clutch switch
39
AIN 1
YES
Brake pedal
56
AIN 2
YES
Vehicle speed (VSS)
54
DIN 1
Yes
Also from CAN, Audi ME 7.5 CAN
EPC light
-
Audi ME 7.5 CAN
CAN only!
Instrument cluster/ABS
-
Audi ME 7.5 CAN
CAN only!
Fuel consumption
No
Cruise control
No
Bluetooth ( MDash)
Yes
EGT option
Yes, direct
6 EGT direct in harness
OEM EGT-sensors
No
Additional connector
The following is the extra connector table in the model-specific guide. Refer to its illustrated connector and installation notes for view, cable colours, electrical limits and revision; these positions are not the factory ECU connector.
Pin
Description
Usage
Note
1 (H)
+5V sensor supply
2 (G)
Sensor GND
3 (F)
TPS AIN
0-5V analog input
4 (E)
AIN 4
0-5V analog input
5 (D)
DIN/VR 4
Digital input
6 (C)
DIN/VR 5
Digital input
7 (B)
GPO 6
Output
Also parallel connected to VVT exhaust valve (if your vehicle has one)
8 (A)
GPO 7 / DIN 3
Output or digital input
9 (S)
10 (R)
11 (P)
12 (N)
+12V
Output at ignition on
13 (M)
Engine GND
14 (L)
GPO 3
Output
15 (K)
DIN 2
Digital input
16 (J)
AIN 3
0-5V analog input
Installation and verification
The adapter may require an external wideband sensor, a MAP hose, additional connectors, or other changes depending on the application and kit. Do not assume that every factory function, emissions device, dashboard feature, air-conditioning function or transmission is supported. Check the model-specific tables, base configuration and full manufacturer installation guide for the exact unit before connection and calibration.
Revision 2: MaxxECU Audi S4/RS4 2.7 biturbo (ME 7.1) plug-in adapterMaxxECU Audi S4/RS4 2.7 biturbo (ME 7.1) plug-in product image. Source: MaxxECU; used with permission. Illustrative kit; confirm included hardware for the particular package.
MaxxECU Audi S4/RS4 2.7 biturbo (ME 7.1) plug-in adapter connects a compatible MaxxECU to an application-specific factory wiring loom. It is an adapter and installation package rather than a new universal ECU architecture. The published MaxxECU application guide identifies its intended configuration and connector details.
Identification and scope
Match the vehicle, engine, original ECU and connector, transmission, adapter revision and the MaxxECU unit to the guide. GEN1 adapters and earlier V1-specific adapters are not automatically interchangeable. The manufacturer's GEN1 adapter index separates the vehicle-specific instructions.
Manufacturer-listed examples
These examples and qualifications are transcribed from the manufacturer's adapter guide. A listed platform is not proof that every market or hardware combination is compatible; check the exact ECU, loom and transmission.
Vehicle
Engine code
Year
LSU sensor
Note
Audi S4 B5 2.7 biturbo
AGB, AZB
1998 - 2002
External sensor needed
Only uses one WBO sensor
Audi RS4 2.7 biturbo
AZR
2001
External sensor needed
Only uses one WBO sensor
Golf R32
BDE
1997 - 2003
Uses stock LSU 4.2 sensor
Not available yet!!
Vehicle and ECU functions
Manufacturer's mapping and availability for this particular adapter; a yes or no applies only to the configuration named in the table. Confirm adapter revision, hardware and calibration with the original guide.
Options
OEM ECU PIN
MaxxECU IO
RACE
Note
VVT solenoid
115
GPO 1
Yes
Check engine light
48
GPO 2 + Audi ME 7.5 CAN
Yes
Boost solenoid (OEM)
104
GPO 4
Yes
Only on turbo engines
Variable intake valve
121
GPO 4
Yes
Only on Golf R32. Can be used to control the variable intake, or for boosted applications the boost solenoid (requires a solenoid to be wired to the valve solenoid connector)
Fuel pump relay
65
GPO 5
Yes
VVT exhaust solenoid
120
GPO 6
Yes
Parallel connected to extra 16-pin connector also if not used.
Tachometer
37
GPO 8 + Audi ME 7.5 CAN
Yes
E-Throttle
117/118
GPO 11/12
Yes
Sequential injection
INJ 1 - 6
Yes
IAC cutoff valve
9
INJ 7
Yes
EVAP
64
INJ 8
Yes
Sequential ignition
IGN 1 - 6
Yes
Knock sensors (OEM)
106, 107
KNOCK1, KNOCK2
Yes
Secondary air pump
44,46
-
No
Intake air temperature sensor
IAT
Yes
Paralell connected with 2-pin extra connector
Coolant temperature sensor
CLT
Yes
Clutch switch
39
AIN 1
YES
Brake pedal
56
AIN 2
YES
Vehicle speed (VSS)
54
DIN 1
Yes
Also from CAN, Audi ME 7.5 CAN
EPC light
-
Audi ME 7.5 CAN
CAN only!
Instrument cluster/ABS
-
Audi ME 7.5 CAN
CAN only!
Fuel consumption
No
Cruise control
No
Bluetooth ( MDash)
Yes
EGT option
Yes, direct
6 EGT direct in harness
OEM EGT-sensors
No
Additional connector
The following is the extra connector table in the model-specific guide. Refer to its illustrated connector and installation notes for view, cable colours, electrical limits and revision; these positions are not the factory ECU connector.
Pin
Description
Usage
Note
1 (H)
+5V sensor supply
2 (G)
Sensor GND
3 (F)
TPS AIN
0-5V analog input
4 (E)
AIN 4
0-5V analog input
5 (D)
DIN/VR 4
Digital input
6 (C)
DIN/VR 5
Digital input
7 (B)
GPO 6
Output
Also parallel connected to VVT exhaust valve (if your vehicle has one)
8 (A)
GPO 7 / DIN 3
Output or digital input
9 (S)
10 (R)
11 (P)
12 (N)
+12V
Output at ignition on
13 (M)
Engine GND
14 (L)
GPO 3
Output
15 (K)
DIN 2
Digital input
16 (J)
AIN 3
0-5V analog input
Installation and verification
The adapter may require an external wideband sensor, a MAP hose, additional connectors, or other changes depending on the application and kit. Do not assume that every factory function, emissions device, dashboard feature, air-conditioning function or transmission is supported. Check the model-specific tables, base configuration and full manufacturer installation guide for the exact unit before connection and calibration.