
Image: Canems, Injection ECU manual, release 2.03, reproduced from The Wedge Shop mirror with permission.
Canems engine management includes a programmable Injection ECU for fuel and ignition control. The historical release 2.03 guide describes up to eight cylinders with wasted spark and four injector drivers; this information does not establish a complete model catalogue.
Individual ECU reference
Canems Injection ECU contains model details, revision comparisons, applications and the full sourced 30-way table. A separate 6- and 8-cylinder ignition-only ECU is documented in its own manual. The full range of Canems hardware and historic variants is not established by the available sources.
Known systems and applications
- Canems Injection ECU, documented in releases 2.03 and 2.17 of the installation manual.
- Rover V8 conversion kit — an application package using a Canems ECU, rather than a separately verified ECU model name.
See Canems Injection ECU manual, release 2.03 and Rover V8 installation guide. A Rover V8 kit page shows the installation.
Injection ECU: hardware and operating scope
The Canems release 2.03 manual describes a programmable ECU with four high-current injector and four ignition outputs for up to eight-cylinder applications using wasted spark. Four-cylinder injection is described as semi-sequential. Ignition can be used without injection on carburetted engines. The manual describes software-selectable MAP or throttle-based load and 1, 2 or 3 bar MAP sensors.
The 2.03 release describes two fuel and ignition maps with 180 sites each; a later Canems release 2.17 manual describes 252 sites. These are manual/software releases, not verified separate ECU model names. Confirm firmware and installation details with the supplier rather than assuming every unit has every feature in the later manual.
Documented features and tuning
- Two switchable fuel and ignition maps, programmable speed and load sites and real-time mapping.
- Crank/cam input, injector phasing, staging, transient enrichment and battery-voltage compensation. Staged injector wiring can depend on the firmware file.
- Programmable dwell, soft and hard speed limiting, main relay and auxiliary outputs; refer to the ECU's actual output ratings.
- Release 2.17 lists optional knock control and internal data logging; those options should not be assumed fitted to all units.
Canems' release 2.17 manual specifies an ABS housing, 30-way connector, RS232 with optional USB, a 7–18 V negative-earth supply and four high-current injector and ignition outputs. It quotes 10 A per injector and ignition output, but its wiring chapter says low-impedance injectors require suitable series ballast resistors. The source also explains RPM signal, throttle, temperatures, relay control and wiring tests. Release 2.17 manual.
Applications and identification
The 14CUX Rover V8 package and pre-serpentine Rover V8 package are conversion kits with application-specific looms, sensors and base maps. Their names describe applications; they are not established here as separate ECU hardware model names. The 2.03 manual also documents development for siamese-port multi-point injection; that claim does not make a generic map suitable for every A-series installation.
Canems has also documented an ignition ECU for six- and eight-cylinder engines. It is a related ignition-only controller, not evidence that the fuel-and-ignition pinout below can be transferred to it.
Injection ECU pinout — manual release 2.03
Thirty-way connector, positions 1A–3K. Use the numbered connector diagram in the manual to establish viewing orientation; this table is for the specific documented ECU and release. Serial connections are preconnected from the factory in this guide.
| Pin | Function |
|---|---|
| 1A | Injector earth |
| 1B | Injector bank 1 |
| 1C | Injector bank 2 |
| 1D | Injector bank 3 |
| 1E | Injector bank 4 |
| 1F | Ignition output 4 |
| 1G | Ignition output 3 |
| 1H | Ignition output 2 |
| 1J | Ignition output 1 |
| 1K | Ignition earth |
| 2A | Map switching input |
| 2B | Air temperature |
| 2C | Coolant temperature |
| 2D | Throttle position |
| 2E | MAP signal |
| 2F | Oxygen sensor 1 |
| 2G | Oxygen sensor 2 |
| 2H | 5 V reference |
| 2J | Main relay output |
| 2K | Output 2 (PWM capable) |
| 3A | ECU earth |
| 3B | 12 V supply |
| 3C | Crank sensor earth and shielding |
| 3D | Crank sensor signal |
| 3E | Cam / road speed signal |
| 3F | Serial ground |
| 3G | Serial receive |
| 3H | Serial transmit |
| 3J | Output 1 |
| 3K | Tachometer |
Confirm the exact ECU, hardware revision and connector orientation before wiring. Configurable functions and electrical limits are model-dependent; consult the linked original diagrams.