Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
DTAFast standalone engine management
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Changes from revision 2 to revision 3

Removed text is struck through; added text is highlighted.

Manufacturer product photograph: DTAFast. Permission to republish confirmed by the user.

DTAFast T4+ is a programmable T-series engine ECU. Four cylinders fully sequential or six and eight semi-sequential. One drive-by-wire throttle, one knock sensor and one variable cam control. Manufacturer specification and product photographs.

Control and software

DTAFast describes configurable inputs and outputs, Bosch wideband control, on-board logging, and a trigger oscilloscope in T-Series PC software. Capabilities, logging rates and pin usage vary by unit and firmware; confirm the exact installation and ECU specification. Product details.

Connector pinout and wiring

Use the T4+ manufacturer wiring diagram for numbered connector cavities, diagram orientation, switched and permanent supplies, grounds, actuators, sensors and hardware-revision notes. Outputs can be configurable: confirm assignments and limits in both the diagram and actual calibration. The similarly named non-plus ECU has its own separate pinout.

Complete connector pin assignmentsThese pin positions and labels are from the DTAFast T4-PLUS wiring diagram, shown from the pin-insertion side. A dash means no function is shown in the drawing. Verify the ECU version, electrical limits and configured functions before wiring.Connector 1 — pinout version 1.04PinFunction in manufacturer diagram1Coil 32-3PWM 34PWM 25PWM 16Motor 1 +7Motor 1 -8-9Injector 110Coil 111-12-13Power Ground 114Power Ground 215-16-17Injector 218Coil 219-20-21-22-23-24-25Injector 426Coil 427-28-29-30-31Ignition 12v In32-33-34Injector 3Connector 2 — pinout version 1.04PinFunction in manufacturer diagram1Analogue 22Wheel 13Analogue 104Digital 15Analogue 36Analogue 47Thermistor 18-95v Output10Analogue 111-12Crank Sensor13-14Digital 415Digital 516Analogue 1117Thermistor 318-19Analogue 620-21Sensor Ground22Cam 123-245v Output25Thermistor 226CAN High27-28CAN Low29-30-31-32-33Sensor Ground34Analogue 9Connector 3 — pinout version 1.04PinFunction in manufacturer diagram1-2-3-4-5-6-7Lambda 1 Pump Current8Lambda 1 VGND9Lambda 1 Heater Negative10PWM 811Lambda 1 Trim Resistor12Lambda 1 Nernst Voltage13-14-15-16-17Analogue 718Analogue 819-20-21-22PWM 423PWM 524PWM 625PWM 726Permanent 12v27Permanent 12v28-29-30-31Knock 132-33-34-

Identification

Record the exact model suffix, hardware revision, firmware, serial and harness before modifying wiring or calibration. Obtain software and manuals from DTAFast and see the DTAFast family reference for related models and legacy controllers.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 2: DTAFast T4 Plus
DTAFast T4 Plus engine management unit
Manufacturer product photograph: DTAFast. Permission to republish confirmed by the user.

DTAFast T4+ is a programmable T-series engine ECU. Four cylinders fully sequential or six and eight semi-sequential. One drive-by-wire throttle, one knock sensor and one variable cam control. Manufacturer specification and product photographs.

Control and software

DTAFast describes configurable inputs and outputs, Bosch wideband control, on-board logging, and a trigger oscilloscope in T-Series PC software. Capabilities, logging rates and pin usage vary by unit and firmware; confirm the exact installation and ECU specification. Product details.

Connector pinout and wiring

Use the T4+ manufacturer wiring diagram for numbered connector cavities, diagram orientation, switched and permanent supplies, grounds, actuators, sensors and hardware-revision notes. Outputs can be configurable: confirm assignments and limits in both the diagram and actual calibration. The similarly named non-plus ECU has its own separate pinout.

Identification

Record the exact model suffix, hardware revision, firmware, serial and harness before modifying wiring or calibration. Obtain software and manuals from DTAFast and see the DTAFast family reference for related models and legacy controllers.

Revision 3: DTAFast T4 Plus
DTAFast T4 Plus engine management unit
Manufacturer product photograph: DTAFast. Permission to republish confirmed by the user.

DTAFast T4+ is a programmable T-series engine ECU. Four cylinders fully sequential or six and eight semi-sequential. One drive-by-wire throttle, one knock sensor and one variable cam control. Manufacturer specification and product photographs.

Control and software

DTAFast describes configurable inputs and outputs, Bosch wideband control, on-board logging, and a trigger oscilloscope in T-Series PC software. Capabilities, logging rates and pin usage vary by unit and firmware; confirm the exact installation and ECU specification. Product details.

Connector pinout and wiring

Use the T4+ manufacturer wiring diagram for numbered connector cavities, diagram orientation, switched and permanent supplies, grounds, actuators, sensors and hardware-revision notes. Outputs can be configurable: confirm assignments and limits in both the diagram and actual calibration. The similarly named non-plus ECU has its own separate pinout.

Complete connector pin assignments

These pin positions and labels are from the DTAFast T4-PLUS wiring diagram, shown from the pin-insertion side. A dash means no function is shown in the drawing. Verify the ECU version, electrical limits and configured functions before wiring.

Connector 1 — pinout version 1.04

PinFunction in manufacturer diagram
1Coil 3
2-
3PWM 3
4PWM 2
5PWM 1
6Motor 1 +
7Motor 1 -
8-
9Injector 1
10Coil 1
11-
12-
13Power Ground 1
14Power Ground 2
15-
16-
17Injector 2
18Coil 2
19-
20-
21-
22-
23-
24-
25Injector 4
26Coil 4
27-
28-
29-
30-
31Ignition 12v In
32-
33-
34Injector 3

Connector 2 — pinout version 1.04

PinFunction in manufacturer diagram
1Analogue 2
2Wheel 1
3Analogue 10
4Digital 1
5Analogue 3
6Analogue 4
7Thermistor 1
8-
95v Output
10Analogue 1
11-
12Crank Sensor
13-
14Digital 4
15Digital 5
16Analogue 11
17Thermistor 3
18-
19Analogue 6
20-
21Sensor Ground
22Cam 1
23-
245v Output
25Thermistor 2
26CAN High
27-
28CAN Low
29-
30-
31-
32-
33Sensor Ground
34Analogue 9

Connector 3 — pinout version 1.04

PinFunction in manufacturer diagram
1-
2-
3-
4-
5-
6-
7Lambda 1 Pump Current
8Lambda 1 VGND
9Lambda 1 Heater Negative
10PWM 8
11Lambda 1 Trim Resistor
12Lambda 1 Nernst Voltage
13-
14-
15-
16-
17Analogue 7
18Analogue 8
19-
20-
21-
22PWM 4
23PWM 5
24PWM 6
25PWM 7
26Permanent 12v
27Permanent 12v
28-
29-
30-
31Knock 1
32-
33-
34-

Identification

Record the exact model suffix, hardware revision, firmware, serial and harness before modifying wiring or calibration. Obtain software and manuals from DTAFast and see the DTAFast family reference for related models and legacy controllers.