Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
DTAFast standalone engine management
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Changes from revision 2 to revision 3

Removed text is struck through; added text is highlighted.

Manufacturer product photograph: DTAFast. Permission to republish confirmed by the user.

Ignition-only controller for carburetted or historic engines; supports distributor ignition on up to 12 cylinders or wasted spark on up to four. It does not control fuel injectors. DTAFast T2i product information.

Features and application

Wideband lambda monitoring and logging, launch, closed-loop flat shift, boost and electric fuel-pump relay control are listed by DTAFast. The fuel pump can be commanded off when the engine stops. All T-series units use the T-Series PC software; DTAFast describes configurable inputs and outputs, integrated Bosch wideband measurement, logging, firmware updates and a built-in trigger oscilloscope. Available functions and channel limits depend on the exact model and firmware. Manufacturer specification.

Identification and wiring

Identify the printed model including any “+” or “i” suffix, hardware revision, connector and firmware before allocating pins. Configurable functions may differ from defaults. Manufacturer T2i wiring diagram and connector pinout contains connector orientation, cavity functions, power, earth and sensor examples. Follow its fuse and load requirements; do not interchange pin numbering with another T-series controller.

Complete connector pin assignmentsThe following tables reproduce the pin positions and labels in the DTAFast T2I wiring diagram. The manufacturer's drawing shows the pin-insertion side. A dash is shown where the drawing has no function assigned; analogue, digital and PWM functions may be configured in software. Verify actual hardware revision, wiring and electrical limits against the source.Connector 1 — pinout version 1.03PinFunction in manufacturer diagram1PWM 12Lambda Nernst Voltage3Coil 14Lambda VGND5Lambda Pump Current6Coil 27Lambda Trim Resistor8-9-10PWM 211Digital 112Wheel 113Power Ground 114Power Ground 215Lambda Heater Negative16CAN High17CAN Low18PWM 319Crank20Analogue 121Permanent 12v22Analogue 223Analogue 324Thermistor 125Analogue 426PWM 4275v Out28Sensor Ground29Sensor Ground30Digital 231Ignition 12v In32Thermistor 233Analogue 534Analogue 6

Software and related information

DTAFast provides model-specific wiring diagrams, firmware, manuals and PC software via its downloads section. Capture the existing calibration and firmware identifiers before making changes. See the DTAFast family overview for earlier S and E series models.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 2: DTAFast T2i
DTAFast T2i engine management unit
Manufacturer product photograph: DTAFast. Permission to republish confirmed by the user.

Ignition-only controller for carburetted or historic engines; supports distributor ignition on up to 12 cylinders or wasted spark on up to four. It does not control fuel injectors. DTAFast T2i product information.

Features and application

Wideband lambda monitoring and logging, launch, closed-loop flat shift, boost and electric fuel-pump relay control are listed by DTAFast. The fuel pump can be commanded off when the engine stops. All T-series units use the T-Series PC software; DTAFast describes configurable inputs and outputs, integrated Bosch wideband measurement, logging, firmware updates and a built-in trigger oscilloscope. Available functions and channel limits depend on the exact model and firmware. Manufacturer specification.

Identification and wiring

Identify the printed model including any “+” or “i” suffix, hardware revision, connector and firmware before allocating pins. Configurable functions may differ from defaults. Manufacturer T2i wiring diagram and connector pinout contains connector orientation, cavity functions, power, earth and sensor examples. Follow its fuse and load requirements; do not interchange pin numbering with another T-series controller.

Software and related information

DTAFast provides model-specific wiring diagrams, firmware, manuals and PC software via its downloads section. Capture the existing calibration and firmware identifiers before making changes. See the DTAFast family overview for earlier S and E series models.

Revision 3: DTAFast T2i
DTAFast T2i engine management unit
Manufacturer product photograph: DTAFast. Permission to republish confirmed by the user.

Ignition-only controller for carburetted or historic engines; supports distributor ignition on up to 12 cylinders or wasted spark on up to four. It does not control fuel injectors. DTAFast T2i product information.

Features and application

Wideband lambda monitoring and logging, launch, closed-loop flat shift, boost and electric fuel-pump relay control are listed by DTAFast. The fuel pump can be commanded off when the engine stops. All T-series units use the T-Series PC software; DTAFast describes configurable inputs and outputs, integrated Bosch wideband measurement, logging, firmware updates and a built-in trigger oscilloscope. Available functions and channel limits depend on the exact model and firmware. Manufacturer specification.

Identification and wiring

Identify the printed model including any “+” or “i” suffix, hardware revision, connector and firmware before allocating pins. Configurable functions may differ from defaults. Manufacturer T2i wiring diagram and connector pinout contains connector orientation, cavity functions, power, earth and sensor examples. Follow its fuse and load requirements; do not interchange pin numbering with another T-series controller.

Complete connector pin assignments

The following tables reproduce the pin positions and labels in the DTAFast T2I wiring diagram. The manufacturer's drawing shows the pin-insertion side. A dash is shown where the drawing has no function assigned; analogue, digital and PWM functions may be configured in software. Verify actual hardware revision, wiring and electrical limits against the source.

Connector 1 — pinout version 1.03

PinFunction in manufacturer diagram
1PWM 1
2Lambda Nernst Voltage
3Coil 1
4Lambda VGND
5Lambda Pump Current
6Coil 2
7Lambda Trim Resistor
8-
9-
10PWM 2
11Digital 1
12Wheel 1
13Power Ground 1
14Power Ground 2
15Lambda Heater Negative
16CAN High
17CAN Low
18PWM 3
19Crank
20Analogue 1
21Permanent 12v
22Analogue 2
23Analogue 3
24Thermistor 1
25Analogue 4
26PWM 4
275v Out
28Sensor Ground
29Sensor Ground
30Digital 2
31Ignition 12v In
32Thermistor 2
33Analogue 5
34Analogue 6

Software and related information

DTAFast provides model-specific wiring diagrams, firmware, manuals and PC software via its downloads section. Capture the existing calibration and firmware identifiers before making changes. See the DTAFast family overview for earlier S and E series models.