Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
Link standalone ECUs
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Changes from revision 1 to revision 3

Removed text is struck through; added text is highlighted.

Manufacturer product image of NS13X application ECU: Link ECU. Permission to republish confirmed by the user.

Link G4X NS13X is a vehicle-specific programmable plug-in ECU for the Nissan S13 application application listed in Link's model-specific manuals index. It is an application board, rather than the universal wire-in ECU. Check the exact vehicle, market, engine, original ECU and board part number against the manufacturer's NS13X installation manual.

Identification and installation

Record the Link model label and revision, donor factory ECU connector and car's engine and year. Plug-in boards connect to particular factory-harness layouts; the family or vehicle name alone does not establish every model-year or transmission combination. The manufacturer manual gives the supported application and any installation or configuration notes for this board.

G4X plug-in platforms offer configurable fuel and ignition control but available channels and features depend on the original header and board. The G4X plug-in general specifications are conditional on the particular application and do not mean every input is brought out to the factory harness.

Pinout and tuning

The NS13X installation manual is the model-specific source for board pinouts, expansion connections, electrical cautions and startup configuration. Use its connector orientation and the exact board version; do not copy a wire-in ECU pinout onto a factory harness. PCLink and manual downloads; Link manufacturer overview.

S13Link header and expansion connector schedulesFrom Link’s S13Link installation manual, pages 15–17. Link views the ECU from the wire side. The cited table distinguishes S13 CA18DET and S14 SR20DET uses; confirm the exact header and engine before wiring. Only source-listed positions are shown and “nc” is reproduced from Link.PinECU channelVehicle function1Ignition 1Ignition2Ignition 2Ignition3Ignition 3Ignition4Injector 5 (Aux)ISC solenoid5Aux 1Boost solenoid S13 CA18DET only6Injector 6 (Aux)A/C out7Aux 2Tacho8Aux 3Intake runner control S13 CA18DET9Injector 6 (Aux)A/C out10Ground11Ignition 3 or 4 (via J1)Ignition12Ignition 4Ignition13nc14nc15nc16ECCS relay controlPulls to ground with ignition on17nc18Aux 4Fuel pump relay19Aux 3Engine fan low speed S14 SR20DET20Ground21nc22nc23Knock 1Knock24ncnc25Aux 6Boost solenoid S14 SR20DET26GroundAFM27An Volt 4AFM signal28An Temp 1ECT29An Volt 1Oxygen signal30Ground (signal)31nc32Aux 7CE light S14 SR20DET33Aux 8CAT light / engine fan high S14 SR20DET34DI 1Power steering switch S14 SR20DET35An Volt 2Factory MAP sensor S14 SR20DET36nc37nc38An Volt 5TPS39nc40nc41Trig 2Trig 242Trig 1Trig 143DI 3Start signal44nc4512 V ignition switch inputControls pin 1646DI 4A/C in47nc48+5 V Out49+14 V ECCS relayECU power50Ground (signal)51Trig 2Trig 252Trig 1Trig 153DI 2Vehicle speed54nc55An Temp 2Factory IAT some S13 CA18DET56nc57nc58nc59+14 V ECCS relayECU power60Ground (signal)101Injector 1Injection102nc103Injector 3Injection104nc105nc106Injector 5 (Aux)ISC solenoid107Ground108Ground109+12 V constantISC flywheeling110Injector 2Injection111nc112Injector 4Injection113Aux 5VTC cam solenoid S14 SR20DET114nc115GroundO2 heater116GroundAux 3 appears on both 8 and 19 with different vehicle functions. Ignition 3 or 4 on 11 depends on jumper J1. Injector drives 7 and 8 are not exposed and lack injector-drive hardware. On-board MAP uses An Volt 3.Expansion connectorPinECU channel1Ground (signal)2+5 V Out3DI 54DI 65DI 76An Volt 67An Temp 48An Temp 39Ignition 510Ignition 611Ignition 712Ignition 813An Volt 814An Volt 915An Volt 1016An Volt 11CAN 1 / RS232PinFunction / cable colour1Comms GND (brown)2CAN1 L (green)3CAN1 H (white)4RS232 RX (grey)5RS232 TX (yellow)CAN 2 / OBDPinFunction / cable colour1GND (brown)2CAN2 L (green)3CAN2 H (white)4NC (grey)5+14 V (yellow)Link cautions that connected serial wires can interfere with USB when CAN 1/RS232 is used for CAN.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 1: Link G4X NS13X plug-in ECU

Link G4X NS13X is a vehicle-specific programmable plug-in ECU for the Nissan S13 application application listed in Link's model-specific manuals index. It is an application board, rather than the universal wire-in ECU. Check the exact vehicle, market, engine, original ECU and board part number against the manufacturer's NS13X installation manual.

Identification and installation

Record the Link model label and revision, donor factory ECU connector and car's engine and year. Plug-in boards connect to particular factory-harness layouts; the family or vehicle name alone does not establish every model-year or transmission combination. The manufacturer manual gives the supported application and any installation or configuration notes for this board.

G4X plug-in platforms offer configurable fuel and ignition control but available channels and features depend on the original header and board. The G4X plug-in general specifications are conditional on the particular application and do not mean every input is brought out to the factory harness.

Pinout and tuning

The NS13X installation manual is the model-specific source for board pinouts, expansion connections, electrical cautions and startup configuration. Use its connector orientation and the exact board version; do not copy a wire-in ECU pinout onto a factory harness. PCLink and manual downloads; Link manufacturer overview.

Revision 3: Link G4X NS13X plug-in ECU
Link G4X NS13X plug-in ECU
Manufacturer product image of NS13X application ECU: Link ECU. Permission to republish confirmed by the user.

Link G4X NS13X is a vehicle-specific programmable plug-in ECU for the Nissan S13 application application listed in Link's model-specific manuals index. It is an application board, rather than the universal wire-in ECU. Check the exact vehicle, market, engine, original ECU and board part number against the manufacturer's NS13X installation manual.

Identification and installation

Record the Link model label and revision, donor factory ECU connector and car's engine and year. Plug-in boards connect to particular factory-harness layouts; the family or vehicle name alone does not establish every model-year or transmission combination. The manufacturer manual gives the supported application and any installation or configuration notes for this board.

G4X plug-in platforms offer configurable fuel and ignition control but available channels and features depend on the original header and board. The G4X plug-in general specifications are conditional on the particular application and do not mean every input is brought out to the factory harness.

Pinout and tuning

The NS13X installation manual is the model-specific source for board pinouts, expansion connections, electrical cautions and startup configuration. Use its connector orientation and the exact board version; do not copy a wire-in ECU pinout onto a factory harness. PCLink and manual downloads; Link manufacturer overview.

S13Link header and expansion connector schedules

From Link’s S13Link installation manual, pages 15–17. Link views the ECU from the wire side. The cited table distinguishes S13 CA18DET and S14 SR20DET uses; confirm the exact header and engine before wiring. Only source-listed positions are shown and “nc” is reproduced from Link.

PinECU channelVehicle function
1Ignition 1Ignition
2Ignition 2Ignition
3Ignition 3Ignition
4Injector 5 (Aux)ISC solenoid
5Aux 1Boost solenoid S13 CA18DET only
6Injector 6 (Aux)A/C out
7Aux 2Tacho
8Aux 3Intake runner control S13 CA18DET
9Injector 6 (Aux)A/C out
10Ground
11Ignition 3 or 4 (via J1)Ignition
12Ignition 4Ignition
13nc
14nc
15nc
16ECCS relay controlPulls to ground with ignition on
17nc
18Aux 4Fuel pump relay
19Aux 3Engine fan low speed S14 SR20DET
20Ground
21nc
22nc
23Knock 1Knock
24ncnc
25Aux 6Boost solenoid S14 SR20DET
26GroundAFM
27An Volt 4AFM signal
28An Temp 1ECT
29An Volt 1Oxygen signal
30Ground (signal)
31nc
32Aux 7CE light S14 SR20DET
33Aux 8CAT light / engine fan high S14 SR20DET
34DI 1Power steering switch S14 SR20DET
35An Volt 2Factory MAP sensor S14 SR20DET
36nc
37nc
38An Volt 5TPS
39nc
40nc
41Trig 2Trig 2
42Trig 1Trig 1
43DI 3Start signal
44nc
4512 V ignition switch inputControls pin 16
46DI 4A/C in
47nc
48+5 V Out
49+14 V ECCS relayECU power
50Ground (signal)
51Trig 2Trig 2
52Trig 1Trig 1
53DI 2Vehicle speed
54nc
55An Temp 2Factory IAT some S13 CA18DET
56nc
57nc
58nc
59+14 V ECCS relayECU power
60Ground (signal)
101Injector 1Injection
102nc
103Injector 3Injection
104nc
105nc
106Injector 5 (Aux)ISC solenoid
107Ground
108Ground
109+12 V constantISC flywheeling
110Injector 2Injection
111nc
112Injector 4Injection
113Aux 5VTC cam solenoid S14 SR20DET
114nc
115GroundO2 heater
116Ground

Aux 3 appears on both 8 and 19 with different vehicle functions. Ignition 3 or 4 on 11 depends on jumper J1. Injector drives 7 and 8 are not exposed and lack injector-drive hardware. On-board MAP uses An Volt 3.

Expansion connector

PinECU channel
1Ground (signal)
2+5 V Out
3DI 5
4DI 6
5DI 7
6An Volt 6
7An Temp 4
8An Temp 3
9Ignition 5
10Ignition 6
11Ignition 7
12Ignition 8
13An Volt 8
14An Volt 9
15An Volt 10
16An Volt 11

CAN 1 / RS232

PinFunction / cable colour
1Comms GND (brown)
2CAN1 L (green)
3CAN1 H (white)
4RS232 RX (grey)
5RS232 TX (yellow)

CAN 2 / OBD

PinFunction / cable colour
1GND (brown)
2CAN2 L (green)
3CAN2 H (white)
4NC (grey)
5+14 V (yellow)

Link cautions that connected serial wires can interfere with USB when CAN 1/RS232 is used for CAN.