Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
Omex standalone ECUs
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Changes from revision 2 to revision 4

Removed text is struck through; added text is highlighted.

Omex 710. Manufacturer product image: source; reproduced with permission.

The 710 is Omex's programmable fuel-and-ignition ECU for a broad range of two- to twelve-cylinder configurations. The manufacturer lists distributor, wasted-spark and individual-coil ignition arrangements, two-stage and compatible continuous cam control, staged injectors, boost control, launch and flat shift. Features and outputs depend on firmware, hardware and engine configuration. Model-specific Omex manual · Omex engine-management range.

Connector and pinout

The Omex 710 hardware manual 2v11 gives connector pins at page 66 and wiring from page 68. FUEL outputs can be allocated as injection or PWM outputs, while some IGN outputs have configurable alternatives. Verify output allocation, driver capability and actual loom before wiring. Open the exact-model installation or hardware manual.

710 ECU loom-plug positions — manual 2v11The table records the ECU plug on the end of the wiring harness, as described in OMEM710 hardware manual 2v11, section 29.2, page 66. Colour pairs are the manual's main colour and tracer for its described loom; confirm the actual cavity labels, loom and connector view. Functions may be configurable. A blank position in the source is not a spare assignment.PositionManual loom colourFunction1AYellow/blackIGN12AYellow/violetIGN63ABrown/pinkFUEL84ARedBattery power5ABlackPower ground 16AGreySensor ground7ABlack screened redCrank sensor8ATiming ground9AWhite/violetCoolant temperature10AWhite/yellowMAP211ARed screened redCam sensor12AYellow/greyIGN21BYellow/orangeIGN42BYellow/greenIGN53BBrown/violetFUEL64BBrown/blackFUEL15BBrown/greenFUEL56BBlue/whiteMAP17BBlackPower ground 28BBrown/greyFUEL79BWhite/greenAir temperature10BBlueKnock sensor11BWhite/orangeOxygen sensor 212BYellow/redIGN31CBlue/greyHIGHSIDE22CBrown/orangeFUEL43CBrown/yellowFUEL24CNot assigned in source5CBlue/blackHIGHSIDE16CBrown/redFUEL37CWhite/redOxygen sensor 18COrangeThrottle position9CPink5 V output10CRed/blueRoad speed sensor11CWhite/pinkALT POWER12CBlue/yellowTachoThe same 36 positions are drawn as a connector face, seen from the wiring-loom side, on Omex 710 connector pinout.

Software and setup

Omex lists MAP4000 for its current ECU range; check the exact unit, firmware and communications lead before attempting to connect. Record ECU serial and firmware, save the existing calibration, and confirm crank trigger, injector, coil, sensors and assigned outputs against the matching manual. Manufacturer startup calibrations require verification and adjustment for the actual engine.

Compare models and historical identities in the Omex family guide. Omex 710 product details.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 2: Omex 710
Omex 710 ECU
Omex 710. Manufacturer product image: source; reproduced with permission.

The 710 is Omex's programmable fuel-and-ignition ECU for a broad range of two- to twelve-cylinder configurations. The manufacturer lists distributor, wasted-spark and individual-coil ignition arrangements, two-stage and compatible continuous cam control, staged injectors, boost control, launch and flat shift. Features and outputs depend on firmware, hardware and engine configuration. Model-specific Omex manual · Omex engine-management range.

Connector and pinout

The Omex 710 hardware manual 2v11 gives connector pins at page 66 and wiring from page 68. FUEL outputs can be allocated as injection or PWM outputs, while some IGN outputs have configurable alternatives. Verify output allocation, driver capability and actual loom before wiring. Open the exact-model installation or hardware manual.

Software and setup

Omex lists MAP4000 for its current ECU range; check the exact unit, firmware and communications lead before attempting to connect. Record ECU serial and firmware, save the existing calibration, and confirm crank trigger, injector, coil, sensors and assigned outputs against the matching manual. Manufacturer startup calibrations require verification and adjustment for the actual engine.

Compare models and historical identities in the Omex family guide. Omex 710 product details.

Revision 4: Omex 710
Omex 710 ECU
Omex 710. Manufacturer product image: source; reproduced with permission.

The 710 is Omex's programmable fuel-and-ignition ECU for a broad range of two- to twelve-cylinder configurations. The manufacturer lists distributor, wasted-spark and individual-coil ignition arrangements, two-stage and compatible continuous cam control, staged injectors, boost control, launch and flat shift. Features and outputs depend on firmware, hardware and engine configuration. Model-specific Omex manual · Omex engine-management range.

Connector and pinout

The Omex 710 hardware manual 2v11 gives connector pins at page 66 and wiring from page 68. FUEL outputs can be allocated as injection or PWM outputs, while some IGN outputs have configurable alternatives. Verify output allocation, driver capability and actual loom before wiring. Open the exact-model installation or hardware manual.

710 ECU loom-plug positions — manual 2v11

The table records the ECU plug on the end of the wiring harness, as described in OMEM710 hardware manual 2v11, section 29.2, page 66. Colour pairs are the manual's main colour and tracer for its described loom; confirm the actual cavity labels, loom and connector view. Functions may be configurable. A blank position in the source is not a spare assignment.

PositionManual loom colourFunction
1AYellow/blackIGN1
2AYellow/violetIGN6
3ABrown/pinkFUEL8
4ARedBattery power
5ABlackPower ground 1
6AGreySensor ground
7ABlack screened redCrank sensor
8ATiming ground
9AWhite/violetCoolant temperature
10AWhite/yellowMAP2
11ARed screened redCam sensor
12AYellow/greyIGN2
1BYellow/orangeIGN4
2BYellow/greenIGN5
3BBrown/violetFUEL6
4BBrown/blackFUEL1
5BBrown/greenFUEL5
6BBlue/whiteMAP1
7BBlackPower ground 2
8BBrown/greyFUEL7
9BWhite/greenAir temperature
10BBlueKnock sensor
11BWhite/orangeOxygen sensor 2
12BYellow/redIGN3
1CBlue/greyHIGHSIDE2
2CBrown/orangeFUEL4
3CBrown/yellowFUEL2
4CNot assigned in source
5CBlue/blackHIGHSIDE1
6CBrown/redFUEL3
7CWhite/redOxygen sensor 1
8COrangeThrottle position
9CPink5 V output
10CRed/blueRoad speed sensor
11CWhite/pinkALT POWER
12CBlue/yellowTacho

The same 36 positions are drawn as a connector face, seen from the wiring-loom side, on Omex 710 connector pinout.

Software and setup

Omex lists MAP4000 for its current ECU range; check the exact unit, firmware and communications lead before attempting to connect. Record ECU serial and firmware, save the existing calibration, and confirm crank trigger, injector, coil, sensors and assigned outputs against the matching manual. Manufacturer startup calibrations require verification and adjustment for the actual engine.

Compare models and historical identities in the Omex family guide. Omex 710 product details.