Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
ECUMaster standalone ECUs
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Changes from revision 2 to revision 3

Removed text is struck through; added text is highlighted.

EMU Pro-8. Manufacturer product image: source; reproduced with permission.

Pro-8 is the smaller ECU in the EMU Pro range, aimed at up to eight-cylinder engines. ECUMaster lists eight peak-and-hold injector outputs, eight software-selectable active or passive ignition outputs, 12 low-side auxiliary outputs, three full H-bridges, two LSU 4.9 controllers, two drive-by-wire controllers, two CAN buses and one LIN bus. The IP65 enclosure measures 165 × 95 × 38 mm. Direct-injection engines need the separate GDI Driver. Manufacturer product specification · Manufacturer comparison.

Connector pinout and wiring

The linked v1.0 pinout specifies three Superseal 1.0 mating housings A 4-1437290-1, B 1473416-1 and C 4-1437290-0. CAN1 serves PC communications and requires external termination; USB is for a flash logging drive. Use the exact PDF drawings for cavity numbers, orientation and current limits. Exact-model manufacturer pinout.

Software and installation

Record the ECU serial, firmware, software and project versions and confirm assigned outputs and trigger inputs before connecting loads. The manufacturer downloads contain current software, manuals and supported base maps. Base maps do not establish the correct pinout for a particular vehicle. Compare with the ECUMaster family guide.

Connector pin tablesThe tables transcribe ECUMaster Pro-8 pinout v1.0. Use the numbered manufacturer connector drawings and mating-housing keys to establish orientation; these tables describe ECU connector positions, not sensor-side terminal numbers. Configurable and shared functions depend on software setup. Refer to the source for protection, currents, grounds, termination and sensor-wiring conditions before use.Connector APinManufacturer functionA1Ignition 8A2Injector 1A3Injector 2A4Injector 3A5Injector 4A6Injector 5A7Injector 6A8Injector 7A9Injector 8A10Ignition 7A11Power groundA12+5 V source AA13Digital 2A14Digital 4A15Digital 8A16Digital 6 (turboshaft)A17Power groundA18Ignition 6A19Power groundA20Digital groundA21Digital 1 (crank)A22Digital 3A23Digital 7A24Digital 5 (turboshaft)A25Auxiliary 9A26Ignition 5A27Ignition 4A28Ignition 3A29Ignition 2A30Ignition 1A31CAN 1 high (PC)A32CAN 1 low (PC)A33CAN 2 highA34CAN 2 lowConnector BPinManufacturer functionB1Auxiliary 1 (wideband heater option)B2Auxiliary 2 (wideband heater option)B3Auxiliary 3 (wideband heater option)B4Auxiliary 4 (wideband heater option)B5Auxiliary 5B6Auxiliary 6B7Auxiliary 7B8+12 V supplyB9Digital ground (flash drive)B10USB D− (flash drive)B11USB D+ (flash drive)B12+5 V source A (flash drive)B13Auxiliary 8B14+12 V supplyB15+12 V switchedB16Knock sensor 1B17Knock sensor 2B18Wideband 2 VGND (LSU 4.9)B19Power groundB20Wideband 1 Ip (LSU 4.9)B21Wideband 1 Vs (LSU 4.9)B22Wideband 1 Rcal (LSU 4.9)B23Wideband 1 VGND (LSU 4.9)B24Wideband 2 Ip (LSU 4.9)B25Wideband 2 Vs (LSU 4.9)B26Wideband 2 Rcal (LSU 4.9)Connector CPinManufacturer functionC1Auxiliary 10C2Auxiliary 11C3Auxiliary 12C4Analogue 7C5Analogue 10 (2.2 kΩ pull)C6H-bridge 1AC7H-bridge 2BC8H-bridge 3AC9H-bridge 2AC10Analogue 1 (MAP)C11Analogue 3C12Analogue 5C13Analogue 8C14Analogue 11 (2.2 kΩ pull)C15Analogue 13 (1 kΩ pull)C16Analogue 15 (330 Ω pull)C17H-bridge 3BC18Analogue 2C19Analogue 4C20Analogue 6C21Analogue 9 (2.2 kΩ pull)C22Analogue 12 (2.2 kΩ pull)C23Analogue 14 (1 kΩ pull)C24Analogue 16 (100 Ω pull)C25H-bridge 1BC26LINC27+5 V source BC28+5 V source BC29Analogue groundC30Power groundC31Precision analogue 1C32Precision analogue 2C33Precision analogue 3C34Precision analogue 4CAN1 carries PC communications and has no internal terminator in the cited document. B9–B12 are the flash-drive connections; they are not the tuning PC connection. All named power and sensor grounds have the specific wiring requirements described by the manufacturer.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 2: ECUMaster EMU Pro-8
EMU Pro-8 ECU
EMU Pro-8. Manufacturer product image: source; reproduced with permission.

Pro-8 is the smaller ECU in the EMU Pro range, aimed at up to eight-cylinder engines. ECUMaster lists eight peak-and-hold injector outputs, eight software-selectable active or passive ignition outputs, 12 low-side auxiliary outputs, three full H-bridges, two LSU 4.9 controllers, two drive-by-wire controllers, two CAN buses and one LIN bus. The IP65 enclosure measures 165 × 95 × 38 mm. Direct-injection engines need the separate GDI Driver. Manufacturer product specification · Manufacturer comparison.

Connector pinout and wiring

The linked v1.0 pinout specifies three Superseal 1.0 mating housings A 4-1437290-1, B 1473416-1 and C 4-1437290-0. CAN1 serves PC communications and requires external termination; USB is for a flash logging drive. Use the exact PDF drawings for cavity numbers, orientation and current limits. Exact-model manufacturer pinout.

Software and installation

Record the ECU serial, firmware, software and project versions and confirm assigned outputs and trigger inputs before connecting loads. The manufacturer downloads contain current software, manuals and supported base maps. Base maps do not establish the correct pinout for a particular vehicle. Compare with the ECUMaster family guide.

Revision 3: ECUMaster EMU Pro-8
EMU Pro-8 ECU
EMU Pro-8. Manufacturer product image: source; reproduced with permission.

Pro-8 is the smaller ECU in the EMU Pro range, aimed at up to eight-cylinder engines. ECUMaster lists eight peak-and-hold injector outputs, eight software-selectable active or passive ignition outputs, 12 low-side auxiliary outputs, three full H-bridges, two LSU 4.9 controllers, two drive-by-wire controllers, two CAN buses and one LIN bus. The IP65 enclosure measures 165 × 95 × 38 mm. Direct-injection engines need the separate GDI Driver. Manufacturer product specification · Manufacturer comparison.

Connector pinout and wiring

The linked v1.0 pinout specifies three Superseal 1.0 mating housings A 4-1437290-1, B 1473416-1 and C 4-1437290-0. CAN1 serves PC communications and requires external termination; USB is for a flash logging drive. Use the exact PDF drawings for cavity numbers, orientation and current limits. Exact-model manufacturer pinout.

Software and installation

Record the ECU serial, firmware, software and project versions and confirm assigned outputs and trigger inputs before connecting loads. The manufacturer downloads contain current software, manuals and supported base maps. Base maps do not establish the correct pinout for a particular vehicle. Compare with the ECUMaster family guide.

Connector pin tables

The tables transcribe ECUMaster Pro-8 pinout v1.0. Use the numbered manufacturer connector drawings and mating-housing keys to establish orientation; these tables describe ECU connector positions, not sensor-side terminal numbers. Configurable and shared functions depend on software setup. Refer to the source for protection, currents, grounds, termination and sensor-wiring conditions before use.

Connector A

PinManufacturer function
A1Ignition 8
A2Injector 1
A3Injector 2
A4Injector 3
A5Injector 4
A6Injector 5
A7Injector 6
A8Injector 7
A9Injector 8
A10Ignition 7
A11Power ground
A12+5 V source A
A13Digital 2
A14Digital 4
A15Digital 8
A16Digital 6 (turboshaft)
A17Power ground
A18Ignition 6
A19Power ground
A20Digital ground
A21Digital 1 (crank)
A22Digital 3
A23Digital 7
A24Digital 5 (turboshaft)
A25Auxiliary 9
A26Ignition 5
A27Ignition 4
A28Ignition 3
A29Ignition 2
A30Ignition 1
A31CAN 1 high (PC)
A32CAN 1 low (PC)
A33CAN 2 high
A34CAN 2 low

Connector B

PinManufacturer function
B1Auxiliary 1 (wideband heater option)
B2Auxiliary 2 (wideband heater option)
B3Auxiliary 3 (wideband heater option)
B4Auxiliary 4 (wideband heater option)
B5Auxiliary 5
B6Auxiliary 6
B7Auxiliary 7
B8+12 V supply
B9Digital ground (flash drive)
B10USB D− (flash drive)
B11USB D+ (flash drive)
B12+5 V source A (flash drive)
B13Auxiliary 8
B14+12 V supply
B15+12 V switched
B16Knock sensor 1
B17Knock sensor 2
B18Wideband 2 VGND (LSU 4.9)
B19Power ground
B20Wideband 1 Ip (LSU 4.9)
B21Wideband 1 Vs (LSU 4.9)
B22Wideband 1 Rcal (LSU 4.9)
B23Wideband 1 VGND (LSU 4.9)
B24Wideband 2 Ip (LSU 4.9)
B25Wideband 2 Vs (LSU 4.9)
B26Wideband 2 Rcal (LSU 4.9)

Connector C

PinManufacturer function
C1Auxiliary 10
C2Auxiliary 11
C3Auxiliary 12
C4Analogue 7
C5Analogue 10 (2.2 kΩ pull)
C6H-bridge 1A
C7H-bridge 2B
C8H-bridge 3A
C9H-bridge 2A
C10Analogue 1 (MAP)
C11Analogue 3
C12Analogue 5
C13Analogue 8
C14Analogue 11 (2.2 kΩ pull)
C15Analogue 13 (1 kΩ pull)
C16Analogue 15 (330 Ω pull)
C17H-bridge 3B
C18Analogue 2
C19Analogue 4
C20Analogue 6
C21Analogue 9 (2.2 kΩ pull)
C22Analogue 12 (2.2 kΩ pull)
C23Analogue 14 (1 kΩ pull)
C24Analogue 16 (100 Ω pull)
C25H-bridge 1B
C26LIN
C27+5 V source B
C28+5 V source B
C29Analogue ground
C30Power ground
C31Precision analogue 1
C32Precision analogue 2
C33Precision analogue 3
C34Precision analogue 4

CAN1 carries PC communications and has no internal terminator in the cited document. B9–B12 are the flash-drive connections; they are not the tuning PC connection. All named power and sensor grounds have the specific wiring requirements described by the manufacturer.