Page organisation in this revision
- Page type
- Reference hub
- Subject
- Engine ECU
- Parent
- Haltech standalone ECUs
- Applies to
- No ECU-specific applicability
- Tool groups
- None
- Manufacturers
- None
Changes from revision 1 to revision 2
Removed text is struck through; added text is highlighted.
Haltech E11V2 is a E series programmable engine-management model. The Haltech E11V2 specification lists up to 12 injector outputs, four PWM outputs, seven auxiliary analogue inputs and four auxiliary digital inputs. Injection and ignition outputs share physical resources in some configurations. Manufacturer specification or guide.
Identification and output allocation
Record the full ECU label, serial number, hardware or harness revision, software and existing calibration. These characteristics are model-specific; a superficially similar E series ECU should not be treated as a drop-in replacement. Counts can be limited by shared outputs, external modules and the engine's ignition and injection strategy.
Model-specific pinout and wiring
Consult the E11V2 wiring documentation and the historic model manuals and connector archive where applicable. Select the named model and the precise harness revision; read its numbered connector view, driver characteristics, injector supply, power and ground notes. The connector appearance alone is not proof of identical pin functions.
Software and further information
legacy software matching the model. Haltech's download centre separates software and provides a legacy section. See Haltech standalone ECUs for the other families.
Manufacturer connector schedulesFrom Haltech's E11V2 autospec main harness wiring diagram, revision A, 3 November 2008; the drawing shows the view looking into the ECU. “Not shown” means the position is not assigned on this harness drawing and does not assert it is electrically unconnected. Haltech's separately archived E11/E8 manual lists 34-way pin 2 as +5 V, but this E11V2 harness diagram does not show a connection there. Verify the specific ECU and loom before using it.34-way ECU connectorPinFunction shown on harness diagram1PWM out 22Not shown3Ignition 14Ignition 25Injector 10 / ignition 36Injector 9 / ignition 47Ignition 5 / injector 88Ignition 6 / injector 79+5 V sensor supply10Ground11ECU ground12+8 V sensor supply13+8 V sensor supply14TPS15MAP16Spare A/D 2 (trim)17Spare A/D 318PWM out 119Injector 120Injector 221Injector 322Injector 423PWM out 324Fuel pump trigger25Spare A/D 426+12 V switched ECU supply27Injector 528Injector 629Injector 12 / aux out 130Injector 11 / aux out 231IDL 132IDL 233IDL 334IDL 426-way ECU connectorPinFunction shown on harness diagram1Trigger2Home3Air temperature4Coolant temperature5Not shown6Not shown7Aux input 18Timed input 19Timed input 210Timed input 311+12 V switched12O2 sensor A13Spare A/D 114Ground15Ground16Ground17TX18RX19PWM out 420Spare A/D 521Spare A/D 622Spare A/D 723CAN high24CAN low25Not shown26Not shownJ2 PC interface on the harnessPinFunction1CAN high2TX3RX5Ground6CAN lowThe other PC connector positions are not specified on the drawing.
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 1: Haltech E11V2
Haltech E11V2 is a E series programmable engine-management model. The Haltech E11V2 specification lists up to 12 injector outputs, four PWM outputs, seven auxiliary analogue inputs and four auxiliary digital inputs. Injection and ignition outputs share physical resources in some configurations. Manufacturer specification or guide.
Identification and output allocation
Record the full ECU label, serial number, hardware or harness revision, software and existing calibration. These characteristics are model-specific; a superficially similar E series ECU should not be treated as a drop-in replacement. Counts can be limited by shared outputs, external modules and the engine's ignition and injection strategy.
Model-specific pinout and wiring
Consult the E11V2 wiring documentation and the historic model manuals and connector archive where applicable. Select the named model and the precise harness revision; read its numbered connector view, driver characteristics, injector supply, power and ground notes. The connector appearance alone is not proof of identical pin functions.
Software and further information
legacy software matching the model. Haltech's download centre separates software and provides a legacy section. See Haltech standalone ECUs for the other families.
Revision 2: Haltech E11V2
Haltech E11V2 is a E series programmable engine-management model. The Haltech E11V2 specification lists up to 12 injector outputs, four PWM outputs, seven auxiliary analogue inputs and four auxiliary digital inputs. Injection and ignition outputs share physical resources in some configurations. Manufacturer specification or guide.
Identification and output allocation
Record the full ECU label, serial number, hardware or harness revision, software and existing calibration. These characteristics are model-specific; a superficially similar E series ECU should not be treated as a drop-in replacement. Counts can be limited by shared outputs, external modules and the engine's ignition and injection strategy.
Model-specific pinout and wiring
Consult the E11V2 wiring documentation and the historic model manuals and connector archive where applicable. Select the named model and the precise harness revision; read its numbered connector view, driver characteristics, injector supply, power and ground notes. The connector appearance alone is not proof of identical pin functions.
Software and further information
legacy software matching the model. Haltech's download centre separates software and provides a legacy section. See Haltech standalone ECUs for the other families.
Manufacturer connector schedules
From Haltech's E11V2 autospec main harness wiring diagram, revision A, 3 November 2008; the drawing shows the view looking into the ECU. “Not shown” means the position is not assigned on this harness drawing and does not assert it is electrically unconnected. Haltech's separately archived E11/E8 manual lists 34-way pin 2 as +5 V, but this E11V2 harness diagram does not show a connection there. Verify the specific ECU and loom before using it.
34-way ECU connector
| Pin | Function shown on harness diagram |
|---|
| 1 | PWM out 2 |
| 2 | Not shown |
| 3 | Ignition 1 |
| 4 | Ignition 2 |
| 5 | Injector 10 / ignition 3 |
| 6 | Injector 9 / ignition 4 |
| 7 | Ignition 5 / injector 8 |
| 8 | Ignition 6 / injector 7 |
| 9 | +5 V sensor supply |
| 10 | Ground |
| 11 | ECU ground |
| 12 | +8 V sensor supply |
| 13 | +8 V sensor supply |
| 14 | TPS |
| 15 | MAP |
| 16 | Spare A/D 2 (trim) |
| 17 | Spare A/D 3 |
| 18 | PWM out 1 |
| 19 | Injector 1 |
| 20 | Injector 2 |
| 21 | Injector 3 |
| 22 | Injector 4 |
| 23 | PWM out 3 |
| 24 | Fuel pump trigger |
| 25 | Spare A/D 4 |
| 26 | +12 V switched ECU supply |
| 27 | Injector 5 |
| 28 | Injector 6 |
| 29 | Injector 12 / aux out 1 |
| 30 | Injector 11 / aux out 2 |
| 31 | IDL 1 |
| 32 | IDL 2 |
| 33 | IDL 3 |
| 34 | IDL 4 |
26-way ECU connector
| Pin | Function shown on harness diagram |
|---|
| 1 | Trigger |
| 2 | Home |
| 3 | Air temperature |
| 4 | Coolant temperature |
| 5 | Not shown |
| 6 | Not shown |
| 7 | Aux input 1 |
| 8 | Timed input 1 |
| 9 | Timed input 2 |
| 10 | Timed input 3 |
| 11 | +12 V switched |
| 12 | O2 sensor A |
| 13 | Spare A/D 1 |
| 14 | Ground |
| 15 | Ground |
| 16 | Ground |
| 17 | TX |
| 18 | RX |
| 19 | PWM out 4 |
| 20 | Spare A/D 5 |
| 21 | Spare A/D 6 |
| 22 | Spare A/D 7 |
| 23 | CAN high |
| 24 | CAN low |
| 25 | Not shown |
| 26 | Not shown |
J2 PC interface on the harness
| Pin | Function |
|---|
| 1 | CAN high |
| 2 | TX |
| 3 | RX |
| 5 | Ground |
| 6 | CAN low |
The other PC connector positions are not specified on the drawing.